Initial commit

target/linux/sunxi/base-files/lib/firmware/brcm/brcmfmac4329-sdio.txt

@@ -0,0 +1,57 @@
+#AP6210_NVRAM_V1.2_03192013
+manfid=0x2d0
+prodid=0x492
+vendid=0x14e4
+devid=0x4343
+boardtype=0x0598
+
+# Board Revision is P307, same nvram file can be used for P304, P305, P306 and P307 as the tssi pa params used are same
+#Please force the automatic RX PER data to the respective board directory if not using P307 board, for e.g. for P305 boards force the data into the following directory /projects/BCM43362/a1_labdata/boardtests/results/sdg_rev0305
+boardrev=0x1307
+boardnum=777
+xtalfreq=26000
+boardflags=0x80201
+boardflags2=0x80
+sromrev=3
+wl0id=0x431b
+macaddr=00:90:4c:07:71:12
+aa2g=1
+ag0=2
+maxp2ga0=74
+cck2gpo=0x2222
+ofdm2gpo=0x44444444
+mcs2gpo0=0x6666
+mcs2gpo1=0x6666
+pa0maxpwr=56
+
+#P207 PA params
+#pa0b0=5447
+#pa0b1=-658
+#pa0b2=-175<div></div>
+
+#Same PA params for P304,P305, P306, P307
+
+pa0b0=5447
+pa0b1=-607
+pa0b2=-160
+pa0itssit=62
+pa1itssit=62
+
+
+cckPwrOffset=5
+ccode=0
+rssismf2g=0xa
+rssismc2g=0x3
+rssisav2g=0x7
+triso2g=0
+noise_cal_enable_2g=0
+noise_cal_po_2g=0
+swctrlmap_2g=0x04040404,0x02020202,0x02020202,0x010101,0x1ff
+temp_add=29767
+temp_mult=425
+
+btc_flags=0x6
+btc_params0=5000
+btc_params1=1000
+btc_params6=63
+

target/linux/sunxi/base-files/lib/firmware/brcm/brcmfmac43362-sdio.txt

@@ -0,0 +1,51 @@
+#AP6181_NVRAM_V1.1_01152013
+#adjuest PA parameter for g/n mode
+manfid=0x2d0
+prodid=0x492
+vendid=0x14e4
+devid=0x4343
+boardtype=0x0598
+
+# Board Revision is P307, same nvram file can be used for P304, P305, P306 and P307 as the tssi pa params used are same
+#Please force the automatic RX PER data to the respective board directory if not using P307 board, for e.g. for P305 boards force the data into the following directory /projects/BCM43362/a1_labdata/boardtests/results/sdg_rev0305
+boardrev=0x1307
+boardnum=777
+xtalfreq=26000
+boardflags=0xa00
+sromrev=3
+wl0id=0x431b
+macaddr=00:90:4c:07:71:12
+aa2g=1
+ag0=2
+maxp2ga0=74
+cck2gpo=0x2222
+ofdm2gpo=0x66666666
+mcs2gpo0=0x7777
+mcs2gpo1=0x7777
+pa0maxpwr=56
+
+#P207 PA params
+#pa0b0=5447
+#pa0b1=-658
+#pa0b2=-175<div></div>
+
+#Same PA params for P304,P305, P306, P307
+
+pa0b0=5447
+pa0b1=-607
+pa0b2=-160
+pa0itssit=62
+pa1itssit=62
+
+
+cckPwrOffset=5
+ccode=0
+rssismf2g=0xa
+rssismc2g=0x3
+rssisav2g=0x7
+triso2g=0
+noise_cal_enable_2g=0
+noise_cal_po_2g=0
+swctrlmap_2g=0x04040404,0x02020202,0x02020202,0x010101,0x1ff
+temp_add=29767
+temp_mult=425

target/linux/sunxi/base-files/lib/firmware/brcm/brcmfmac43430-sdio.txt

@@ -0,0 +1,53 @@
+#AP6212_NVRAM_V1.0_20140603
+# 2.4 GHz, 20 MHz BW mode
+
+# The following parameter values are just placeholders, need to be updated.
+manfid=0x2d0
+prodid=0x0726
+vendid=0x14e4
+devid=0x43e2
+boardtype=0x0726
+boardrev=0x1101
+boardnum=22
+macaddr=00:90:4c:c5:12:38
+sromrev=11
+boardflags=0x00404201
+xtalfreq=26000
+nocrc=1
+ag0=255
+aa2g=1
+ccode=ALL
+
+pa0itssit=0x20
+extpagain2g=0
+
+#PA parameters for 2.4GHz, measured at CHIP OUTPUT
+pa2ga0=-168,7161,-820
+AvVmid_c0=0x0,0xc8
+cckpwroffset0=5
+
+# PPR params
+maxp2ga0=90
+txpwrbckof=6
+cckbw202gpo=0x5555
+legofdmbw202gpo=0x77777777
+mcsbw202gpo=0xaaaaaaaa
+
+# OFDM IIR :
+ofdmdigfilttype=7
+# PAPD mode:
+papdmode=2
+
+il0macaddr=00:90:4c:c5:12:38
+wl0id=0x431b
+
+#OOB parameters
+hostwake=0x40
+hostrdy=0x41
+usbrdy=0x03
+usbrdydelay=100
+deadman_to=0xffffffff
+# muxenab: 0x1 for UART enable, 0x10 for Host awake
+muxenab=0x10
+# CLDO PWM voltage settings - 0x4 - 1.1 volt
+#cldo_pwm=0x4

target/linux/sunxi/base-files/lib/preinit/03_b53_hack.sh

@@ -0,0 +1,18 @@
+#!/bin/sh
+
+do_b53_hack() {
+	. /lib/functions.sh
+
+	# hack: enable switch on Lamobo R1 and reset counters
+	case "$(board_name)" in
+	"lamobo,lamobo-r1")
+		ifconfig eth0 up
+		sleep 1
+		swconfig dev switch0 set reset 1
+		swconfig dev switch0 set reset_mib 1
+		swconfig dev switch0 set apply 1
+		;;
+	esac
+}
+
+boot_hook_add preinit_main do_b53_hack

target/linux/sunxi/base-files/lib/preinit/79_move_config

@@ -0,0 +1,20 @@
+#!/bin/sh
+# Copyright (C) 2012-2015 OpenWrt.org
+
+move_config() {
+	local partdev
+
+	. /lib/upgrade/common.sh
+
+	if export_bootdevice && export_partdevice partdev -1; then
+		if mount -t vfat -o rw,noatime "/dev/$partdev" /mnt; then
+			if [ -f /mnt/sysupgrade.tgz ]; then
+				mv -f /mnt/sysupgrade.tgz /
+			fi
+			umount /mnt
+		fi
+	fi
+}
+
+boot_hook_add preinit_mount_root move_config
+

target/linux/sunxi/base-files/lib/upgrade/platform.sh

@@ -0,0 +1,89 @@
+platform_check_image() {
+	local diskdev partdev diff
+
+	export_bootdevice && export_partdevice diskdev -2 || {
+		echo "Unable to determine upgrade device"
+		return 1
+	}
+
+	get_partitions "/dev/$diskdev" bootdisk
+
+	#extract the boot sector from the image
+	get_image "$@" | dd of=/tmp/image.bs count=1 bs=512b 2>/dev/null
+
+	get_partitions /tmp/image.bs image
+
+	#compare tables
+	diff="$(grep -F -x -v -f /tmp/partmap.bootdisk /tmp/partmap.image)"
+
+	rm -f /tmp/image.bs /tmp/partmap.bootdisk /tmp/partmap.image
+
+	if [ -n "$diff" ]; then
+		echo "Partition layout has changed. Full image will be written."
+		ask_bool 0 "Abort" && exit 1
+		return 0
+	fi
+}
+
+platform_copy_config() {
+	local partdev
+
+	if export_partdevice partdev -1; then
+		mount -t vfat -o rw,noatime "/dev/$partdev" /mnt
+		cp -af "$CONF_TAR" /mnt/
+		umount /mnt
+	fi
+}
+
+platform_do_upgrade() {
+	local diskdev partdev diff
+
+	export_bootdevice && export_partdevice diskdev -2 || {
+		echo "Unable to determine upgrade device"
+		return 1
+	}
+
+	sync
+
+	if [ "$SAVE_PARTITIONS" = "1" ]; then
+		get_partitions "/dev/$diskdev" bootdisk
+
+		#extract the boot sector from the image
+		get_image "$@" | dd of=/tmp/image.bs count=1 bs=512b
+
+		get_partitions /tmp/image.bs image
+
+		#compare tables
+		diff="$(grep -F -x -v -f /tmp/partmap.bootdisk /tmp/partmap.image)"
+	else
+		diff=1
+	fi
+
+	if [ -n "$diff" ]; then
+		get_image "$@" | dd of="/dev/$diskdev" bs=4096 conv=fsync
+
+		# Separate removal and addtion is necessary; otherwise, partition 1
+		# will be missing if it overlaps with the old partition 2
+		partx -d - "/dev/$diskdev"
+		partx -a - "/dev/$diskdev"
+
+		return 0
+	fi
+
+	#write uboot image
+	get_image "$@" | dd of="$diskdev" bs=1024 skip=8 seek=8 count=1016 conv=fsync
+	#iterate over each partition from the image and write it to the boot disk
+	while read part start size; do
+		part="$(($part - 2))"
+		if export_partdevice partdev $part; then
+			echo "Writing image to /dev/$partdev..."
+			get_image "$@" | dd of="/dev/$partdev" ibs="512" obs=1M skip="$start" count="$size" conv=fsync
+		else
+			echo "Unable to find partition $part device, skipped."
+		fi
+	done < /tmp/partmap.image
+
+	#copy partition uuid
+	echo "Writing new UUID to /dev/$diskdev..."
+	get_image "$@" | dd of="/dev/$diskdev" bs=1 skip=440 count=4 seek=440 conv=fsync
+}