Initial commit

target/linux/lantiq/files-4.14/arch/mips/boot/dts/VR200.dtsi

@@ -0,0 +1,219 @@
+#include "vr9.dtsi"
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/mips/lantiq_rcu_gphy.h>
+
+/ {
+	memory@0 {
+		reg = <0x0 0x7f00000>;
+	};
+
+	usb_vbus: regulator-usb-vbus {
+		compatible = "regulator-fixed";
+
+		regulator-name = "USB_VBUS";
+
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		gpio = <&gpio 33 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&eth0 {
+	lan: interface@0 {
+		compatible = "lantiq,xrx200-pdi";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0>;
+		mtd-mac-address = <&romfile 0xf100>;
+		lantiq,switch;
+
+		ethernet@0 {
+			compatible = "lantiq,xrx200-pdi-port";
+			reg = <0>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy0>;
+			// gpios = <&gpio 42 GPIO_ACTIVE_LOW>;
+		};
+		ethernet@5 {
+			compatible = "lantiq,xrx200-pdi-port";
+			reg = <5>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy5>;
+		};
+		ethernet@2 {
+			compatible = "lantiq,xrx200-pdi-port";
+			reg = <2>;
+			phy-mode = "gmii";
+			phy-handle = <&phy11>;
+		};
+		ethernet@3 {
+			compatible = "lantiq,xrx200-pdi-port";
+			reg = <4>;
+			phy-mode = "gmii";
+			phy-handle = <&phy13>;
+		};
+	};
+
+	mdio@0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "lantiq,xrx200-mdio";
+		reg = <0>;
+
+		phy0: ethernet-phy@0 {
+			reg = <0x0>;
+			compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
+		};
+		phy5: ethernet-phy@5 {
+			reg = <0x5>;
+			compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
+		};
+		phy11: ethernet-phy@11 {
+			reg = <0x11>;
+			compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
+		};
+		phy13: ethernet-phy@13 {
+			reg = <0x13>;
+			compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
+		};
+	};
+};
+
+&gphy0 {
+	lantiq,gphy-mode = <GPHY_MODE_GE>;
+};
+
+&gphy1 {
+	lantiq,gphy-mode = <GPHY_MODE_GE>;
+};
+
+&gpio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&state_default>;
+
+	state_default: pinmux {
+		mdio {
+			lantiq,groups = "mdio";
+			lantiq,function = "mdio";
+		};
+		gphy-leds {
+			lantiq,groups = "gphy0 led1", "gphy1 led1";
+			lantiq,function = "gphy";
+			lantiq,pull = <2>;
+			lantiq,open-drain = <0>;
+			lantiq,output = <1>;
+		};
+		phy-rst {
+			lantiq,pins = "io42";
+			lantiq,pull = <0>;
+			lantiq,open-drain = <0>;
+			lantiq,output = <1>;
+		};
+		pcie-rst {
+			lantiq,pins = "io38";
+			lantiq,pull = <0>;
+			lantiq,output = <1>;
+		};
+	};
+	pins_spi_default: pins_spi_default {
+		spi_in {
+			lantiq,groups = "spi_di";
+			lantiq,function = "spi";
+		};
+		spi_out {
+			lantiq,groups = "spi_do", "spi_clk",
+				"spi_cs4";
+			lantiq,function = "spi";
+			lantiq,output = <1>;
+		};
+	};
+};
+
+&pci0 {
+	status = "okay";
+	gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>;
+};
+
+&spi {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_spi_default>;
+
+	m25p80@4 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <4 0>;
+		spi-max-frequency = <33250000>;
+		m25p,fast-read;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				reg = <0x0 0x20000>;
+				label = "u-boot";
+				read-only;
+			};
+
+			partition@20000 {
+				reg = <0x20000 0xf90000>;
+				label = "firmware";
+			};
+
+			partition@fb0000 {
+				reg = <0xfb0000 0x10000>;
+				label = "radioDECT";
+				read-only;
+			};
+
+			partition@fc0000 {
+				reg = <0xfc0000 0x10000>;
+				label = "config";
+				read-only;
+			};
+
+			romfile: partition@fd0000 {
+				reg = <0xfd0000 0x10000>;
+				label = "romfile";
+				read-only;
+			};
+
+			partition@fe0000 {
+				reg = <0xfe0000 0x10000>;
+				label = "rom";
+				read-only;
+			};
+
+			partition@ff0000 {
+				reg = <0xff0000 0x10000>;
+				label = "radio";
+				read-only;
+			};
+		};
+	};
+};
+
+&usb_phy0 {
+	status = "okay";
+};
+
+&usb_phy1 {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+	vbus-supply = <&usb_vbus>;
+};
+
+&usb1 {
+	status = "okay";
+	vbus-supply = <&usb_vbus>;
+};