ipq807x: add Xiaomi AX3600

Xiaomi AX3600 is a budget 802.11ax dual-band router/AP.
Specifications:
* CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz
* RAM: 512MB of DDR3
* Storage: 256MB of parallel NAND
* Ethernet: 4x1G RJ45 ports (QCA8075) with 1x status LED per port
* WLAN:
	* PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT
	* 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
	* 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate
* LED-s:
	* System (Blue and Yellow)
	* IoT (Blue)
	* Network (Blue and Yellow)
* Buttons: 1x Soft reset
* Power: 12V DC Jack

Installation instructions:

Obtaining SSH access is mandatory
https://openwrt.org/inbox/toh/xiaomi/xiaomi_ax3600#obtain_ssh_access

Installation is done by the ubiformat method, through SSH:
1. Open an SSH shell to the router
2. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi to the /tmp directory
3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1):
nvram get flag_boot_rootfs

4. Find the rootfs and rootfs_1 mtd indexes respectively:
cat /proc/mtd
Please confirm if mtd12 and mtd13 are the correct indexes from above!

5. Use the command ubiformat to flash the opposite mtd with UBI image:

If nvram get flag_boot_rootfs returned 0:
ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit

otherwise:
ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit

6. Reboot the device by:
reboot

Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step
since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages.
Continue in order to pernamently flash OpenWrt:

7. SSH into OpenWrt from one of the LAN ports
8. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin to the /tmp directory
9. Sysupgrade the device:
sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin

Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>

package/firmware/ipq-wifi/Makefile

@@ -41,6 +41,7 @@ ALLWIFIBOARDS:= \
 	qxwlan_e2600ac-c2 \
 	sony_ncp-hg100-cellular \
 	teltonika_rutx \
+	xiaomi_ax3600 \
 	zte_mf18a \
 	zte_mf289f
 
@@ -50,7 +51,7 @@ define Package/ipq-wifi-default
   SUBMENU:=ath10k Board-Specific Overrides
   SECTION:=firmware
   CATEGORY:=Firmware
-  DEPENDS:=@(TARGET_ipq40xx||TARGET_ipq806x)
+  DEPENDS:=@(TARGET_ipq40xx||TARGET_ipq806x||TARGET_ipq807x)
   TITLE:=Custom Board
 endef
 
@@ -59,17 +60,26 @@ define ipq-wifi-install-one-to
   $(INSTALL_DATA) $(1) $(2)/lib/firmware/ath10k/$(3)/board-2.bin
 endef
 
+define ipq-wifi-install-ath11-one-to
+  $(INSTALL_DIR)  $(2)/lib/firmware/ath11k/$(3)/
+  $(INSTALL_DATA) $(1) $(2)/lib/firmware/ath11k/$(3)/board-2.bin
+endef
+
 define ipq-wifi-install-one
   $(if $(filter $(suffix $(1)),.QCA4019 .qca4019),\
     $(call ipq-wifi-install-one-to,$(1),$(2),QCA4019/hw1.0),\
   $(if $(filter $(suffix $(1)),.QCA9888 .qca9888),\
     $(call ipq-wifi-install-one-to,$(1),$(2),QCA9888/hw2.0),\
+  $(if $(filter $(suffix $(1)),.QCA9889 .qca9889),\
+    $(call ipq-wifi-install-one-to,$(1),$(2),QCA9887/hw1.0),\
   $(if $(filter $(suffix $(1)),.QCA9984 .qca9984),\
     $(call ipq-wifi-install-one-to,$(1),$(2),QCA9984/hw1.0),\
   $(if $(filter $(suffix $(1)),.QCA99X0 .qca99x0),\
     $(call ipq-wifi-install-one-to,$(1),$(2),QCA99X0/hw2.0),\
+  $(if $(filter $(suffix $(1)),.IPQ8074 .ipq8074),\
+    $(call ipq-wifi-install-ath11-one-to,$(1),$(2),IPQ8074/hw2.0),\
     $(error Unrecognized board-file suffix '$(suffix $(1))' for '$(1)')\
-  ))))
+  ))))))
 
 endef
 # Blank line required at end of above define due to foreach context
@@ -102,7 +112,7 @@ Do not install it for any other device!
 endef
 
 # Add board name to ALLWIFIBOARDS
-# Place files in this directory as board-<devicename>.<qca4019|qca9888|qca9984|qca99x0>
+# Place files in this directory as board-<devicename>.<qca4019|qca9888|qca9889|qca9984|qca99x0|ipq8074>
 # Add $(eval $(call generate-ipq-wifi-package,<devicename>,<display name>))
 
 $(eval $(call generate-ipq-wifi-package,aruba_ap-365,Aruba AP-365))
@@ -121,6 +131,7 @@ $(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac-c1,Qxwlan E2600AC C1))
 $(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac-c2,Qxwlan E2600AC C2))
 $(eval $(call generate-ipq-wifi-package,sony_ncp-hg100-cellular,Sony NCP-HG100/Cellular))
 $(eval $(call generate-ipq-wifi-package,teltonika_rutx,Teltonika RUTX))
+$(eval $(call generate-ipq-wifi-package,xiaomi_ax3600,Xiaomi AX3600))
 $(eval $(call generate-ipq-wifi-package,zte_mf18a,ZTE MF18A))
 $(eval $(call generate-ipq-wifi-package,zte_mf289f,ZTE MF289F))