The interrupt handler reads from the mailbox if no other reason for the
interrupt is known. If a spurious interrupt is received just after a
mailbox message has been sent, this means that the response to the
previous message is read again and returned by DSL_BSP_SendCMV instead
of the actual response.
To fix this, check the status register before reading from the mailbox
in the interrupt handler.
Tested on Fritzbox 7320. Without this change, there is occasionally a
kernel panic due to an out-of-bounds memory access in the ltq-adsl
driver (in DSL_DRV_DEV_G997_SnrAllocationNscGet), as a result of an
incorrect value returned by DSL_DRV_DANUBE_CmvRead. This is reproducible
by calling "dsl_cpe_pipe.sh g997dsnrg 1 1" multiple times.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/19385
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Building perf on mips/malta fails on intel-pt-decoder due to a header issue
previously seen in f434643857 ("perf: fix build on PowerPC"):
In file included from util/intel-pt-decoder/intel-pt-insn-decoder.c:12:
util/intel-pt-decoder/../../../arch/x86/include/asm/insn.h: In function 'insn_field_set':
util/intel-pt-decoder/../../../arch/x86/include/asm/insn.h:56:21: error: implicit declaration of function '__cpu_to_le32'; did you mean 'cpu_to_le32'? [-Wimplicit-function-declaration]
56 | p->little = __cpu_to_le32(v);
| ^~~~~~~~~~~~~
| cpu_to_le32
util/intel-pt-decoder/../../../arch/x86/include/asm/insn.h: In function 'insn_set_byte':
util/intel-pt-decoder/../../../arch/x86/include/asm/insn.h:64:20: error: implicit declaration of function '__le32_to_cpu'; did you mean 'le32_to_cpu'? [-Wimplicit-function-declaration]
64 | p->value = __le32_to_cpu(p->little);
| ^~~~~~~~~~~~~
| le32_to_cpu
Extend the previous powerpc fix to mips, disabling intel-pt-decoder build.
cc: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/19426
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Package driver modules for I2C HID devices such as touchpads,
touchscreens and trackpoints found on some laptops. Only the ACPI
firmware variant of the driver is packaged for now as that's what I got
for testing.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The number of serial interfaces for the chip 8250 can be configured at
build time. This is currently not configurable and is always set to 16
interfaces. This is too little for some small embedded devices and too much
for others (x86_64). Therefore, this commit creates the possibility to set
this at compile time.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Link: https://github.com/openwrt/openwrt/pull/19217
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add new option to bootmenu which allows to boot the system from USB.
You can use dd to prepare USB with initramfs:
- dd bs=1M if=openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-factory.ubi of=/dev/sdX
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18949
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Dell/SonicWall APL27-0B1 (marketed as SonicPoint ACi) is a dual band
wireless access point. Very similar to already supported APL26-0AE,
which all antennas are external, while this variant has internal
antennas. End of life as of 2022-07-31.
Specification
SoC: QualcommAtheros QCA9550
RAM: 256 MB DDR2
Flash: 32 MB SPI NOR
WIFI: 2.4 GHz 3T3R integrated
5 GHz 3T3R QCA9890 oversized Mini PCIe card
Ethernet: 2x 10/100/1000 Mbps QCA8334
port labeled lan1 is PoE capable (802.3at)
USB: 1x 2.0
LEDs: LEDs: 6x which 5 are GPIO controlled and two of them are dual color
Buttons: 1x GPIO controlled
Serial: RJ-45 port, SonicWall pinout
baud: 115200, parity: none, flow control: none
Before flashing, be sure to have a copy of factory firmware, in case You
wish to revert to original firmware.
Installation
1. Prepare TFTP server with OpenWrt sysupgrade image and rename that
image to "ap135.bin".
2. Connect to one of LAN ports.
3. Connect to serial port.
4. Hold the reset button (small through hole on side of the unit),
power on the device and when prompted to stop autoboot, hit any key.
The held button can now be released.
5. Alter U-Boot environment with following commands:
setenv bootcmd bootm 0x9F110000
saveenv
6. Adjust "ipaddr" (access point, default is 192.168.1.1) and "serverip"
(TFTP server, default is 192.168.1.10) addresses in U-Boot
environment, then run following commands:
tftp 0x80060000 ap135.bin
erase 0x9F110000 +0x1EF0000
cp.b 0x80060000 0x9F110000 $filesize
7. After successful flashing, execute:
boot
8. The access point will boot to OpenWrt. Wait few minutes, until the
wrench LED will stop blinking, then it's ready for configuration.
Notes
By default no power is provided on USB port, so attached USB devices
won't enumerate. To change that enable regulator with:
echo "enabled" > /sys/devices/platform/output-usb-vbus/state
To disable power write "disabled" to the same file.
Ther regulator state will reset on reboot, consider running this command
on hotplug event or add it to /etc/rc.local. The hotplug event should
look like this:
if [ "${PRODUCT}" = "1d6b/2/606" ] && [ "${ACTION}" = "add" ]; then
echo "enabled" > /sys/devices/platform/output-usb-vbus/state
fi
Place it in /etc/hotplug.d/usb/10-usb-power.
Known issues
Initramfs image can't be bigger than specified kernel size, otherwise
bootloader will throw LZMA decompressing error. Switching to lzma-loader
should workaround that.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250529202033.28250-2-tmn505@terefe.re/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Upstream has disabled SHA-1 algorithms by default since version 2025.87.
SHA-1 has known weakness and most SSH implementations support alternatives.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
It's hard or even impossible to track affected sources
so it's safe to remove all built objects (if any).
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
This allows to fine-tune dropbear build options.
This change is heavily based on similar work done by Marius Dinu earlier
so I'd like to say many thanks to original author.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Correctly load the list of basic_rates from UCI. basic-rates shall be
stored as a option-list. The current code did not retrieve this list
correctly.
wpa_supplicant uses a different config option to set basic-rates
when operating in mesh-mode.
Use the correct config key and calculation for mesh-interfaces.
Signed-off-by: David Bauer <mail@david-bauer.net>
Since upstream commit:
b809fc656e763296f227b9b31e8f225e5977a8af ("perf build: Shellcheck support
for OUTPUT directory")
perf will attempt to run shellcheck on the test shell scripts, however
there is no point in doing this in OpenWrt and while perf checks for
shellcheck presence on your host it can fail to build in some cases.
So, simply disable it for now.
Link: https://github.com/openwrt/openwrt/pull/19361
Signed-off-by: Robert Marko <robimarko@gmail.com>
BUILD_BPF_SKEL was set to 1 by default in upstream commit:
9925495d96efc14d885ba66c5696f664fe0e663c ("perf build: Default
BUILD_BPF_SKEL, warn/disable for missing deps")
Prior to that, it was disabled by default and you had to enable it to
build BPF skeleton support.
So in order to fix perf compilation with kernel 6.12, lets disable
BUILD_BPF_SKEL.
Fixes: #19310
Link: https://github.com/openwrt/openwrt/pull/19361
Signed-off-by: Robert Marko <robimarko@gmail.com>
Without the newly introduced flag, building with libc ends in errors such the below.
There is an upstream fix[1], but backporting it is not straight forward.
/scratch/union/staging_dir/toolchain-x86_64_gcc-15.1.0_glibc/x86_64-openwrt-linux-gnu/include/c++/15.1.0/cstddef:81:21: error: redefinition of 'struct std::__byte_operand<unsigned char>'
81 | template<> struct __byte_operand<unsigned char> { using __type = byte; };
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
/scratch/union/staging_dir/toolchain-x86_64_gcc-15.1.0_glibc/x86_64-openwrt-linux-gnu/include/c++/15.1.0/cstddef:78:21: note: previous definition of 'struct std::__byte_operand<unsigned char>'
78 | template<> struct __byte_operand<bool> { using __type = byte; };
| ^~~~~~~~~~~~~~~~~~~~
make[4]: *** [Makefile:438: ../obj_s/cursesp.o] Error 1
1. https://ncurses.scripts.mit.edu/?p=ncurses.git;a=commit;h=394a1a6cf317912584592e33184ef550e738a4b9
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/19335
Signed-off-by: Robert Marko <robimarko@gmail.com>
Split the xcrypt package build into two Makefiles and a common part for
the version definition in order to work-around build problems when
combining VARIANT with BUILDONLY and scoped InstallDev.
This is done in order to skip build of libcrypt-compat in case we are
not building against glibc in order to prevent libcrypt.so shared
library being present in staging_dir and by that breaking multiple
packages which then will link against it.
Fixes: e3cf7088f1 ("libcrypt-compat: introduce package")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://github.com/openwrt/openwrt/pull/19353
Signed-off-by: Robert Marko <robimarko@gmail.com>
6df761e0e6c7 mt76: fix signature of platform_driver remove funtions for newer kernels
5724be1a6b12 wifi: mt76: Replace strlcpy() with strscpy()
c4a114e2b8c9 wifi: mt76: fix queue assignment for deauth packets
243e572d89fc wifi: mt76: add a wrapper for wcid access with validation
e41c7785589f wifi: mac80211: get tx power per link
d70f62b8f1c7 wifi: mt76: fix vif link allocation
7b3cd3274a24 wifi: mt76: mt7996: Fix secondary link lookup in mt7996_mcu_sta_mld_setup_tlv()
cf89b6218043 wifi: mt76: mt7996: Rely on for_each_sta_active_link() in mt7996_mcu_sta_mld_setup_tlv()
d71108eedab1 wifi: mt76: mt7996: Do not set wcid.sta to 1 in mt7996_mac_sta_event()
32f8c5849ed1 wifi: mt76: mt7996: Fix mlink lookup in mt7996_tx_prepare_skb
ffff9f71e29d wifi: mt76: mt7996: Fix possible OOB access in mt7996_tx()
afe63e758196 wifi: mt76: mt7996: Fix valid_links bitmask in mt7996_mac_sta_{add,remove}
68dd28b99dad wifi: mt76: mt7996: Add MLO support to mt7996_tx_check_aggr()
293778652452 wifi: mt76: mt7996: Move num_sta accounting in mt7996_mac_sta_{add,remove}_links
a94166b21e20 wifi: mt76: Get rid of dma_sync_single_for_device() for MMIO devices
87873d854e51 wifi: mt76: mt7925: Fix null-ptr-deref in mt7925_thermal_init()
06ba3d5e91f4 wifi: mt76: mt792x: Limit the concurrent STA and SoftAP to operate on the same channel
b9f4e0df317d wifi: mt76: mt792x: improve monitor interface handling
ec95319fd3fb wifi: mt76: mt7921s: Introduce SDIO WiFi/BT combo module card reset
dd2d862251cb firmware: add missing mt7990 eeprom files
05eaa56bc7a4 firmware: update mt7992 firmware to 20250328
32ca2b6db354 firmware: update mt7996 firmware to 20250328
Signed-off-by: Felix Fietkau <nbd@nbd.name>
