The factory image generation for the Genexis EX400 image currently fails
if CONFIG_TARGET_ROOTFS_INITRAMFS is disabled.
Create the factory image only if said config option is enabled to avoid
failing builds.
Signed-off-by: David Bauer <mail@david-bauer.net>
Move MIPS reloc patch from pending to hack and rework it to adapt to new
kernel 6.12 version.
This required an additional patch. While at it also improve the text
with the original info without cut.
Link: https://github.com/openwrt/openwrt/pull/16547
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix the resets of the GE_PHY and Uniphy found on the IPQ5018 SoC.
Bitmasks are used to perform multiple resets simultaneously, including
the RX and TX clocks. This enables the Uniphy to properly shift between
SGMII/1G and SGMII+/2.5G modes.
While at it, properly reorder the patches, and rename some to follow
naming standards.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18638
Signed-off-by: Robert Marko <robimarko@gmail.com>
Patch 620-net_sched-codel-do-not-defer-queue-length-update.patch is
actually an ancient patch that somehow manage to be ported for 7 solid
years.
This comes from [1] where a fix patch was proposed. Nobody notice that
the proposed patch was actually rejected upstream in favor of [2]. And
the upstream fix patch is present in kernel from version 4.18.
This means that we were actually fixing for a non existant bug and maybe
introducing regression down the line.
Drop the patch for good as we already have a fix for it in flace for a
long time.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=109581
[2] 35b42da69e
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
As part of the previous commit to add the #clock-cells property to the
GE PHY, the PHY was inadvertently moved under the second mdio node in
the dtsi, and therefore broke the init sequence as the driver was trying
to use the wrong mdio bus to set the init values (ex. DAC, MSE, and AZ).
So let's move it back under the right mdio node and, while at it, pad
the register addresses to 8 hex numbers and re-order properties in line
with Linux DTS coding standards.
Fixes: 6782d0e66f
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18634
Signed-off-by: Robert Marko <robimarko@gmail.com>
Drop the firmware image entry "factory.ubi" from IMAGES for ELECOM
WRC-X3000GS2.
`Device/UbiFit` is added in the early stage of working for adding
support of the device, but finally, only `KERNEL_IN_UBI` is neccesary
and factory.ubi is not. So `Device/UbiFit` should have been replaced
to `KERNEL_IN_UBI` but it was forgotten.
Fixes: 3b7d72bc2e ("qualcommax: add support for ELECOM WRC-X3000GS2")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18611
Signed-off-by: Robert Marko <robimarko@gmail.com>
Hardware
--------
SOC: MediaTek MT7981b
RAM: 256MB DDR3
FLASH: 128MB SPI-NAND (Winbond W25N01GV)
WIFI: Mediatek MT7981b DBDC 802.11ax 2.4/5 GHz
ETH: MediaTek MT7531 Switch
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)
Installation
-----------------------------------------------------------
Vendor-UI Method
-----------------------------------------------------------
1. Download the OpenWrt initramfs.trx image.
2. Connect the PC via LAN to one of the yellow router ports and wait
until your PC to get a DHCP lease.
3. Browse to http://192.168.50.1
4. If your router is brand new, finish the setup process and log into
the Web-UI.
5. Navigate to Administration -> Firmware Upgrade and upload the
downloaded OpenWrt image.
6. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
-----------------------------------------------------------
TFTP Method
-----------------------------------------------------------
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
reachable at 192.168.1.70/24. Rename the image to rtax52.bin.
2. Connect the PC with TFTP server to the RT-AX52.
Set a static ip on the ethernet interface of your PC.
(ip address: 192.168.1.70, subnet mask:255.255.255.0)
Conect to the serial console,
interrupt the autoboot process by pressing '4' when prompted.
3. Download & Boot the OpenWrt initramfs image.
$ setenv ipaddr 192.168.1.1
$ setenv serverip 192.168.1.70
$ tftpboot 0x46000000 rtax52.bin
$ bootm 0x46000000
4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
---------------------------------------------------------------------------
Revert to stock firmware:
1: Download the rt-ax52 firmware from ASUS official website. Save
the firmware to tftp server directory and rename to RT-AX52.trx
2: Connect the PC with TFTP server to the RT-AX52.
Set a static ip on the ethernet interface of your PC.
(ip address: 192.168.1.70, subnet mask:255.255.255.0)
3: Conect to the serial console, power on again, interrupt the
autoboot process by pressing '4' when prompted.
$: ubi remove linux
$: ubi remove jffs2
$: ubi remove rootfs
$: ubi remove rootfs_data
$: ubi create linux 0x45fe000
$: reset
Then the dut will reboot,interrupt the autoboot process by
pressing '2' when prompted.
2: Load System code then write to Flash via TFTP.
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
$: enter y
you will see the follow, type enter directly:
Input device IP (192.168.1.1) ==:
Input server IP (192.168.1.70) ==:
Input Linux Kernel filename (RT-AX52.trx) ==:
4: wait for the device run up
Based on support for ASUS RT-AX52 by liudongdongdong7397
and trx image generation by remittor
Signed-off-by: Christoph Krapp <achterin@gmail.com>
This commit fixes mistaken executable bit on
mt7981b-mercusys-mr80x-v3.dts file.
Fixes: 7921e48d43 ("mediatek: add support for Mercusys MR80X v3")
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Fix nand-ecc-strength property in the spi-nand node of GL-iNet GL-B3000
to 4, to solve the following ECC error on that spi-nand chip.
[ 1.551618] ubi0: attaching mtd11
[ 1.552331] ubi0 warning: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 0:0, read only 64 bytes, retry
[ 1.554455] ubi0 warning: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 0:0, read only 64 bytes, retry
[ 1.565931] ubi0 warning: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 0:0, read only 64 bytes, retry
[ 1.576568] ubi0 error: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 0:0, read 64 bytes
[ 1.587146] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.6.87 #0
[ 1.597153] Hardware name: GL.iNet GL-B3000 (DT)
[ 1.602881] Call trace:
[ 1.607739] dump_backtrace+0xa0/0xe0
[ 1.609910] show_stack+0x18/0x24
[ 1.613728] dump_stack_lvl+0x48/0x60
[ 1.617027] dump_stack+0x18/0x24
[ 1.620672] ubi_io_read+0x11c/0x32c
[ 1.623972] ubi_io_read_ec_hdr+0x50/0x1f0
[ 1.627618] ubi_attach+0x35c/0x133c
[ 1.631524] ubi_attach_mtd_dev+0x494/0xaf4
[ 1.635257] ubi_init_attach+0xac/0x2e4
[ 1.639163] do_one_initcall+0x6c/0x1fc
[ 1.642983] kernel_init_freeable+0x204/0x2e4
[ 1.646803] kernel_init+0x28/0x1dc
[ 1.651316] ret_from_fork+0x10/0x20
The GL-B3000 has a Winbond W25N01GW and the spare size (oobsize) of it
is 64. So the maximum available ECC strength with the qpic-snand driver
is 4 but not 8.
The "nand-ecc-strength" property was not used before the commit
fc3ff2af0c ("qualcommax: allow overriding ECC strength for qpic-snand")
and calculated from the registered spare size in the Linux Kernel. As a
result, we had no issues on the GL-B3000 with the wrong ECC strength
value.
Fixes: 3307fe8ee4 ("qualcommax: ipq50xx: add support for GL.iNET GL-B3000")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18595
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specification:
- MT7620A 580 MHz MIPS24KEc
- 64MB RAM
- 8MB SPI NOR
- MediaTek MT7612E 5.0GHz 802.11a/n/ac
- MediaTek MT7620 2.4GHz 802.11b/g/n
- 5 LEDs (white)
- 1 button
- 1 Gbit port Realtek RTL8211E GbE Phy
Serial Interface:
- 3 Pins GND, RX, TX
- Settings: 57600, 8N1
Based on support from edimax_ew-7476rpc/edimax_ew-747x
and netgear_ex3700/netgear_ex3x00_ex61xx
Notes:
- ATM there is no known way to revert to stock firmware
Flash instruction:
The only known way to flash OpenWrt image is to use tftp in U-Boot, with the
aid of a serial adapter for U-Boot console access:
1. Open the device and connect to the serial port. The device is very similar
to Edimax 7476RPC. See https://openwrt.org/toh/edimax/ew-7476rpc. No VCC!
2. Configure PC with static IP 192.168.1.2/24 and tftp server and
connect PC to device using an ethernet cable.
3. Power on the device and, on the serial console, as soon as U-Boot starts
loading, press "2" to interrupt loading.
4. Enter device ip address 192.168.1.1, PC ip address 192.168.1.2
and the firmware filename placed on the TFTP server.
5. Device will download file from server, write it to flash and reboot.
Signed-off-by: Hugo Monteiro <monteiro.hugo@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16956
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ELECOM WRC-X3000GS2 is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on
IPQ5018.
Specification:
- SoC : Qualcomm IPQ5018
- RAM : DDR3 256 MiB (Zentel A3T2GF40CBF-HP)
- Flash : SPI-NAND 128 MiB (Macronix MX35UF1G24AD-Z4I)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Qualcomm IPQ5018 (SoC)
- 5 GHz : Qualcomm Atheros QCN6102
- Ethernet : 5x 10/100/1000 Mbps
- wan (phy) : Qualcomm IPQ5018 (SoC)
- lan (switch) : Qualcomm Atheros QCA8337
- LEDs/Keys (GPIO): 8x/3x
- UART : through-hole on PCB, 4pins near the barcode
- assignment : 3.3V, TX, RX, NC, GND from the barcode side
- settings : 115200n8
- Power : 12 VDC, 1 A (Max. 11.5W)
Flash instruction using initramfs-factory.bin image:
1. Boot WRC-X3000GS2 normally with router mode
2. Access to the WebUI ("http://192.168.2.1/") on the device and open
the firmware update page ("ファームウェア更新")
3. Select the OpenWrt factory.bin image and click apply ("適用") button
4. Wait ~120 seconds to complete flashing
Switching to the stock firmware:
1. Load the elecom.sh script
. /lib/upgrade/elecom.sh
2. Check the current index of rootfs
bootconfig_rw_index 0:bootconfig rootfs
3. Set the index to inverted value
bootconfig_rw_index 0:bootconfig rootfs <value>
bootconfig_rw_index 0:bootconfig1 rootfs <value>
example:
- step2 returned "0":
bootconfig_rw_index 0:bootconfig rootfs 1
bootconfig_rw_index 0:bootconfig1 rootfs 1
- step2 returned "1":
bootconfig_rw_index 0:bootconfig rootfs 0
bootconfig_rw_index 0:bootconfig1 rootfs 0
4. Reboot
Partition Layout (Stock FW):
0x000000000000-0x000000080000 : "0:SBL1"
0x000000080000-0x000000100000 : "0:MIBIB"
0x000000100000-0x000000140000 : "0:BOOTCONFIG"
0x000000140000-0x000000180000 : "0:BOOTCONFIG1"
0x000000180000-0x000000280000 : "0:QSEE"
0x000000280000-0x000000380000 : "0:QSEE_1"
0x000000380000-0x0000003c0000 : "0:DEVCFG"
0x0000003c0000-0x000000400000 : "0:DEVCFG_1"
0x000000400000-0x000000440000 : "0:CDT"
0x000000440000-0x000000480000 : "0:CDT_1"
0x000000480000-0x000000500000 : "0:APPSBLENV"
0x000000500000-0x000000640000 : "0:APPSBL"
0x000000640000-0x000000780000 : "0:APPSBL_1"
0x000000780000-0x000000880000 : "0:ART"
0x000000880000-0x000000900000 : "0:TRAINING"
0x000000900000-0x000003c40000 : "rootfs"
0x000003c40000-0x000003fc0000 : "Config"
0x000003fc0000-0x000007300000 : "rootfs_1"
0x000007300000-0x000007680000 : "Config_2"
0x000007680000-0x000007b80000 : "Reserved"
0x000007b80000-0x000007c00000 : "FWHEADER"
0x000007c00000-0x000007c80000 : "Factory"
Known Issues:
- All Wi-Fi related peripherals are disabled.
This device has only 256 MiB RAM and it's too few for ath11k. To
prevent OOM when using LuCI or other softwares, disable Wi-Fi related
peripherals in device tree at the moment.
- This device has a Macronix MX35UF1G24AD SPI-NAND chip registered as
oobsize=128 in Linux Kernel. But using BCH8 breaks I/O on the chip
with the following errors, so this support uses BCH4 instead.
root@OpenWrt:~# strings /dev/mtdblock10
[26427.133154] mtdblock: MTD device '0:appsblenv' is NAND, please consider using UBI block devices instead.
[26427.134125] I/O error, dev mtdblock10, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 2
[26427.142240] I/O error, dev mtdblock10, sector 8 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 2
[26427.151427] I/O error, dev mtdblock10, sector 16 op 0x0:(READ) flags 0x80700 phys_seg 2 prio class 2
[26427.160440] I/O error, dev mtdblock10, sector 24 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2
[26427.169619] I/O error, dev mtdblock10, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[26427.178083] Buffer I/O error on dev mtdblock10, logical block 0, async page read
Notes:
- This device has dual-boot feature and it's managed by the index in the
0:bootconfig and 0:bootconfig1 partitions.
MAC Addresses:
LAN : 38:97:A4:xx:xx:60 (0:APPSBLENV, "eth1addr"/"ethaddr" (text))
WAN : 38:97:A4:xx:xx:63 (0:APPSBLENV, "eth0addr" (text))
2.4 GHz: 38:97:A4:xx:xx:61 (0:APPSBLENV, "wifi0" (text))
5 GHz : 38:97:A4:xx:xx:62 (0:APPSBLENV, "wifi1" (text))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18543
Signed-off-by: Robert Marko <robimarko@gmail.com>
To further improve cleanup and maintenance usage, move the kernel
version files to target/linux/generic directory. This permits to self
contain any change to the specific generic directory instead of having
to bload the include directory of periodic changes.
In kernel-version.mk we now use GENERIC_PLATFORM_DIR provided by
target.mk. To make this work, we need to move the inclusion of
kernel-version.mk in target.mk right after GENERIC_PLATFORM_DIR is
defined.
This also comes to permit downstream project to provide a custom generic
directory and specify the kernel version complete of the hash and the
minor version without having to affect other feeds.
In such case both generic and the target directory are provided as feeds
and OpenWrt reference these specific one instead of the generic one.
For downstream it's still suggested and preferable to all match the
shipped generic kernel minor version but this change permits to at least
enforce good practice instead of having to bloat OpenWrt include file of
all kind of downstream changes (making porting to OpenWrt mainline even
more difficult)
Link: https://github.com/openwrt/openwrt/pull/18537
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
