Since 24.10.0, eth0, used for the WAN interface, does not work. From dmesg:
...
[ 1.831126] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module
[ 1.846204] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 19
...
[ 1.933969] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module
[ 1.967668] mt7530-mdio mdio-bus:1f: configuring for fixed/rgmii link mode
[ 1.975999] mt7530-mdio mdio-bus:1f eth0 (uninitialized): PHY [mt7530-0:00] driver [MediaTek MT7530 PHY] (irq=21)
[ 1.986907] mt7530-mdio mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx
[ 1.987149] mtk_soc_eth 1e100000.ethernet eth0: error -17 registering interface eth0
[ 2.004157] mt7530-mdio mdio-bus:1f eth1 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7530 PHY] (irq=22)
[ 2.017698] mtk_soc_eth 1e100000.ethernet eth0: entered promiscuous mode
[ 2.024849] DSA: tree 0 setup
...
[ 4.249680] mtk_soc_eth 1e100000.ethernet dsa: renamed from eth0
...
Like #15865, it seems that gmac0 does not rename eth0 to dsa until after the
switch ports are initialized, leading to a name collision (error -17 = EEXIST).
This patch follows #17062 by using openwrt,netdev-name to fix the collision.
Signed-off-by: J. S. Seldenthuis <jseldenthuis@lely.com>
Link: https://github.com/openwrt/openwrt/pull/18082
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 4fed462454)
The M1200 v1 is similar to the TR1200 series from Cudy. Differences:
- Only 1 LAN port
- No USB
Specifications:
- MT7628
- MT7628AN (2.4G b/g/n) and MT7613BE (5G ac/n) wifi
- 128 MB RAM
- 16 MB flash
MAC Addresses:
- There is one on the label, e.g. xx:xx:xx:xx:xx:A4
- LAN (bottom connector) is the same as the label, e.g. xx:xx:xx:xx:xx:A4
- WAN (top connector) is label + 1, e.g. xx:xx:xx:xx:xx:A5
- WLAN (2.4G) is the same as the label, e.g. xx:xx:xx:xx:xx:A4
- WLAN (5G) is label + 2, e.g. xx:xx:xx:xx:xx:A6
UART:
- is available via the pin holes on the board
- The pinout is printed to the board: P: VCC, G: GND, R: RX, T:TX
- RX and TX require solder bridges to be installed
- Do NOT connect VCC
- Settings: 3.3V, 115200, 8N1
GPIO:
- There are two LEDs: Red (GPIO 4) and White (GPIO 0)
- There are two buttons: Reset (GPIO 11) and WPS (GPIO 5)
Migration to OpenWrt:
- Download the migration image from the Cudy website (it should be available as soon as OpenWrt officially supports the device)
- Connect computer to LAN (bottom connector) and flash the migration image via OEM web interface
- OpenWrt is now accessible via 192.168.1.1
Revert back to OEM firmware:
- Set up a TFTP server on IP 192.168.1.88 and connect to the WAN port (upper port)
- Provide the Cudy firmware as recovery.bin in the TFTP server
- Press the reset button while powering on the device
- Recovery process is started now
- When recovery process is done, OEM firmware is accessible via 192.168.10.1 again
General information:
- No possibility to load a initramfs image via U-Boot because there is no option to interrupt U-Boot
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18233
(cherry picked from commit c13a050d5a)
Link: https://github.com/openwrt/openwrt/pull/18252
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The M1300 v2 is similar to the WR1300 series from Cudy. Differences:
- Only 1 LAN port
- No USB
Specifications:
- MT7621
- MT7603E (2.4G b/g/n) and MT7613BE (5G ac/n) wifi
- 128 MB RAM
- 16 MB flash
MAC Addresses:
- There is one on the label, e.g. xx:xx:xx:xx:xx:1C
- LAN (bottom connector) is the same as the label, e.g. xx:xx:xx:xx:xx:1C
- WAN (top connector) is label +2, e.g. xx:xx:xx:xx:xx:1E
- WLAN (2.4G) is the same as the label, e.g. xx:xx:xx:xx:xx:1C
- WLAN (5G) is the same as WAN, e.g. xx:xx:xx:xx:xx:1E
UART:
- is available via the pin holes on the board
- From inner to outer pin: TX, RX, GND, VCC
- Do NOT connect VCC
- Settings: 3.3V, 115200, 8N1
GPIO:
- There are two LEDs: Red (GPIO 3) and White (GPIO 4)
- There are two buttons: Reset (GPIO 8) and WPS (GPIO 10)
Migration to OpenWrt:
- Download the migration image from the Cudy website (it should be available as soon as OpenWrt officially supports the device)
- The migration image is also available here until a image is provided by Cudy: https://github.com/RolandoMagico/openwrt-build/releases/tag/M1300_Build_20240222
- File: openwrt-ramips-mt7621-cudy_m1300-v2-squashfs-flash-signed.bin
- Connect computer to LAN (bottom connector) and flash the migration image via OEM web interface
- In the migration image, LAN and WAN are swapped. Computer must be connected to the other port after flashing
- OpenWrt is now accessible via 192.168.1.1
- After flashing an up to date OpenWrt image, LAN and WAN settings are again the same as in the OEM firmware
- So use the other connector again
Revert back to OEM firmware:
- Set up a TFTP server on IP 192.168.1.88 and connect to the LAN port (lower port)
- Provide the Cudy firmware as recovery.bin in the TFTP server
- Press the reset button while powering on the device
- Recovery process is started now
- When recovery process is done, OEM firmware is accessible via 192.168.10.1 again
General information:
- No possibility to load a initramfs image via U-Boot because there is no option to interrupt U-Boot
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18139
(cherry picked from commit 8a78637670)
Link: https://github.com/openwrt/openwrt/pull/18204
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for Genexis Pulse EX400 / Inteno Pulse EX400. A branded
variant for the Finnish ISP DNA has already been added in fea2264d9f
(ramips: mt7621: Add DNA Valokuitu Plus EX400, 2023-07-31). This commit
adds support for the generic variants with Inteno and Genexis branding.
Inteno changed its name to Genexis and both brandings exist.
In terms of electronics, there is no difference between the DNA-branded
version and other brandings. LED markings on the case are different,
though. While the DNA-version has a "software-update" LED, the other
versions have a WPS LED. To reduce user confusion, create a separate
image.
Add the different device-tree with the different LED and rename things
to work the same way for both variants.
Specifications:
- Device: Genexis Pulse EX400 / Inteno Pulse EX400
- SoC: MT7621A
- Flash: 256 MB NAND
- RAM: 256 MB
- Ethernet: Built-in, 2 x 1 GbE
- Wifi: MT7603 2.4 GHz 2x2 MIMO, MT7615 5 GHz 4x4 MU-MIMO
- USB: 1x 2.0
- LEDs (GPIO): green/red status, green WPS
- LEDs (SX9512, unsupported): Broadband, Wi-Fi 2.4G, Wi-Fi 5G
- Buttons (GPIO): Reset
- Buttons (SX9512, unsupported): Wi-Fi 2.4G, Wi-Fi 5G, WPS
MAC addresses:
- LAN: U-Boot 'ethaddr' (label)
- WAN: label + 1
- 2.4 GHz: label + 6
- 5 GHz: label + 7
Serial:
There is a black block connector next to the red ethernet connector. It
is accessible also through holes in the casing.
Pinout (TTL 3.3V)
+---+---+
|Tx |Rx |
+---+---+
|Vcc|Gnd|
+---+---+
Firmware:
The vendor firmware is a fork of OpenWrt (Reboot) with a kernel version
4.4.93. The flash is arranged as below and there is a dual boot
mechanism alternating between rootfs_0 and rootfs_1.
+-------+------+------+-----------+-----------+
| | env1 | env2 | rootfs_0 | rootfs_1 |
| +------+------+-----------+-----------+
| | UBI volumes |
+-------+-------------------------------------+
|U-Boot | UBI |
+-------+-------------------------------------+
|mtd0 | mtd1 |
+-------+-------------------------------------+
| NAND |
+---------------------------------------------+
In OpenWrt rootfs_0 will be used as a boot partition that will contain the
kernel and the dtb. The squashfs rootfs and overlay are standard OpenWrt
behaviour.
+-------+------+------+-----------+--------+------------+
| | env1 | env2 | rootfs_0 | rootfs | rootfs_data|
| +------+------+-----------+--------+------------+
| | UBI volumes |
+-------+-----------------------------------------------+
|U-Boot | UBI |
+-------+-----------------------------------------------+
|mtd0 | mtd1 |
+-------+-----------------------------------------------+
| NAND |
+-------------------------------------------------------+
U-boot:
With proper serial access, booting can be halted to U-boot by pressing
any key. TFTP and flash writes are available, but only the first one has
been tested.
NOTE: Recovery mode can be accessed by holding down the reset button while
powering on the device. The led 'Update' will show a solid green light
once ready. A web server will be running at 192.168.1.1:80 and it will
allow flashing a firmware package. You can cycle between rootfs_0 and
rootfs_1 by pressing the reset button once.
Root password:
With the vendor web UI create a backup of your settings and download the
archive to your computer. Within the archive in the file
/etc/shadow replace the password hash for root with that of a password you
know. Restore the configuration with the vendor web UI and you will have
changed the root password.
SSH access:
You might need to enable the SSH service for LAN interface as by default
it's enabled for WAN only.
Installing OpenWrt:
With the vendor web UI, or from the U-Boot recovery UI, install the
OpenWrt factory image. Alternatively, ssh to the device and use
sysupgrade -n from cli.
Finalize by installing the OpenWrt sysupgrade image to get a fully
functioning system.
Reverting to the vendor firmware:
Boot with OpenWrt initramfs image
- Remove volumes rootfs_0, rootfs and rootfs_data and create vendor
volumes.
ubirmvol /dev/ubi0 -n 2
ubirmvol /dev/ubi0 -n 3
ubirmvol /dev/ubi0 -n 4
ubimkvol /dev/ubi0 -N rootfs_0 -S 990
ubimkvol /dev/ubi0 -N rootfs_1 -S 990
Power off and enter to the U-boot recovery to install the vendor
firmware.
Signed-off-by: Andreas Gnau <andreas.gnau@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/17551
(cherry picked from commit 3e7337feea)
Link: https://github.com/openwrt/openwrt/pull/18238
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is an industrial 4G router equipped with OpenWrt 14.07 OEM
customized version
WARNING: The original firmware device tree is common to multiple
boards, and the device tree name is H9350. This submitted device
tree is a modified version, which deletes the non-this-device parts
and adds GPIO watchdog.
Specification:
- SoC: MediaTek MT7620A
- Flash: 16 MB
- RAM: 128 MB
- Power: DC 5V-36V 1.5A
- Ethernet: 1x WAN, 4x LAN (10/100 Mbps)
- Wireless radio: 802.11n 2.4g-only
- LED:
System/Power (RUN): GPIO/26 active-low
Ethernet: 1x WAN, 4x LAN
Modem 1: GPIO/66 active-low
RF 1 (Modem 1 Signal): GPIO/67 active-low
Modem 2: GPIO 71 active-low
RF 2 (Modem 2 Signal): GPIO/24 active-low
WLAN: GPIO/72 active-low
WPS: GPIO/12 active-low
- Button:
WPS / RESET: GPIO/34 active-low
- UART: 1x UART on PCB - 115200 8N1
- GPIO Watchdog: GPIO/62 mode=toggle timeout=1s
- PCIe: 2x miniPCIe for modem
- SIM Slots: 2x SIM Slots
Issue:
- No factory partition, eeprom is located
at /lib/firmware/mt7620a.eeprom
Flash instruction:
Using UART:
1. Configure PC with a static IP address and setup an TFTP server.
2. Put rootfs into the tftp directory.
3. Connect the UART line as described on the PCB.
4. Power up the device and press Ctrl+C to break auto boot.
5. Use `system 6` command and follow the instruction to set device
and tftp server IP address and input the rootfs file name.
U-boot will then load the rootfs and write it into
the flash.
6. Use `system 1` command and follow the instruction to set device
and tftp server IP address and input the firmware file name.
U-boot will then load the firmware once.
7. Login to LuCI and use LuCI upgrade firmware.
Original Firmware Dump / More details:
https://blog.gov.cooking/archives/research-hongdian-h8922-and-flash.html
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Tested-by: Coia Prant <coiaprant@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17472
Link: https://github.com/openwrt/openwrt/pull/18221
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 6a1bdcf545)
Since commit f1c9afd801 ("ramips: mt7621-dts: mux phy0/4 to gmac1") the
USW-Flex lan1 port has been attached directly to the CPU. This improves
routing performance but hinders switching.
This is a generally accepted trade-off in that commit but for USW-Flex it
is a questionable choice. This switch is designed to deliver PoE to remote
places and using it as a router is unlikely. Meanwhile, the lan1 port is
also PoE-in and will often be the uplink, carrying most of the traffic.
Reverting f1c9afd801 for USW-Flex restores full 1 Gbps switching
performance on all ports.
Signed-off-by: Anders Melchiorsen <amelchio@nogoto.net>
Link: https://github.com/openwrt/openwrt/pull/17703
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 62872f8bfd)
There are only 5 devices in mt76x8 sub-target selected the MTK SDXC
driver package. And they are all single ethernet port routers or dev
boards:
* LinkIt Smart 7688
* Onion Omega2+
* RAVPower RP-WD009
* VoCore VoCore2
* VoCore VoCore2-Lite
For these devices, they are using the ephy p1 - p4 as the SDXC IO
pins. Therefore, these GPIO pads must be configured in "digital"
IO mode.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit f5996ae947)
The Zbtlink ZBT-WE2426-B is an indoor dual band WiFi router
with 4 external non detachable antennas and 5 Fast Ethernet ports.
Hardware of ZBT-WE2426-B:
- SoC: MT7628AN
- RAM: 64 MB (Winbond W9751G6K8-25)
- Storage: 8 MB SPI flash (S25FL064K)
- Ethernet: 5x 10/100 Mbps LAN1,LAN2,LAN3,LAN4 & WAN
- Wireless: 2.4GHz: on SoC (802.11b/g/n)
- Wireless: 5GHz: Mediatek MT7612EN (802.11n/ac)
- LEDs: 8x
- Buttons: 1x reset
- USB: 1x 2.0
- MicroSD slot: 1x
- Power: 9 VDC, 1 A
- Uart: GND TX RX PWR - J1 on the PCB
- Board silkscreen: "ZBT-WE2426-C V04" "2018-02-28" "CTT" "13 18"
Backup the stock firmware, settings and calibration data:
This router comes with PandoraBox OpenWrt firmware, so it is
possible to get all MTD partitions using scp.
Installation:
- Using the bootloader web server. Hold the reset button while turning
the power on. Upload the sysupgrade image on http://192.168.1.1.
- Using the sysupgrade command in PandoraBox OpenWrt.
LEDs:
- LAN1,LAN2,LAN3,LAN4,WAN,WLAN2G use GPIO pins of the MT7628AN SoC
(GPIOs 43,42,41,40,39,44)
- WLAN5G uses pin of MT7612EN.
- The POWER LED is directly connected to the VCC. It can be reconnected to
the GPIO 37 of the MT7628AN SoC by resoldering SMD resistor on the PCB.
Buttons:
- The RESET button is connected to the GPIO 38 of the MT7628AN SoC.
MAC addresses as verified by OEM firmware:
use address source
2g *:b0 factory 0x4 (label)
5g *:b1 factory 0x8004
LAN *:b2 factory 0x28
WAN *:b3 factory 0x2e
Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
Link: https://github.com/openwrt/openwrt/pull/16927
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 3a9752ea02)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Edgerouter X currently has its eth1 port on the switch missing since there
is a naming conflict currently.
So, as the root cause is mixing kernel support for DSA interfaces having
predictable names set via "label" property vs others having it assigned
dynamically lets avoid the conflict by using our own custom property as
suggested upstream [1].
So, add support via "openwrt,netdev-name" property and use it on ERX.
Fixes: 2a25c6ace8 ("ramips: get rid of downstream network device label patch")
Fixes: #15643
Link: https://github.com/openwrt/openwrt/pull/17062
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 5695267847)
The Ralink GPIO driver supports irqchip function. Hence we need to
add "interrupt-parent" and "interrupt-controller" properties to make
sure it works properly. It is worth noting that all GPIO devices
share the same interrupt line.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16764
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Gemtek WVRTM-127ACN is an indoor dual band wifi router
with internal antennas and 3 Gigabit Ethernet ports.
The Gemtek WVRTM-130ACN is an indoor dual band wifi router
with external antennas and 5 Gigabit Ethernet ports.
Hardware of WVRTM-127ACN:
- SoC: Mediatek MT7621AT (880 MHz, dual core)
- RAM: 128 MB
- Storage: 128 MB NAND SLC flash
- Ethernet: 3x 10/100/1000 Mbps LAN1,LAN2 & WAN
- Wireless: 2.4GHz: Mediatek MT7603EN (802.11b/g/n)
- Wireless: 5GHz: Mediatek MT7612EN (802.11n/ac)
- LEDs: 11x
- Buttons: 2x WPS, reset
- USB: 1x 3.0
- Power: 56 VDC, 0.54 A, PoE+ IN (WAN)
- PoE: 1x PoE+ 802.3af/at (WAN)
- Uart: GND RX TX VCC - J2 (GND near WAN)
- Board silkscreen: "WVRTM-127ACN_V02" "19K-513-8500R" "RoHS" "1717"
Hardware of WVRTM-130ACN:
- SoC: Mediatek MT7621AT (880 MHz, dual core)
- RAM: 128 MB (Kioxia TC58BVG0S3HTA00)
- Storage: 128 MB NAND SLC (Winbond W971GG6SB-25)
- Ethernet: 5x 10/100/1000 Mbps LAN1,LAN2,LAN3,LAN4 & WAN
- Wireless: 2.4GHz and 5GHz Mediatek MT7615DN (802.11ac/b/g/n) (DBDC)
- LEDs: 10x
- Buttons: 3x Power, WPS, reset
- USB: 1x 3.0
- Power: 56 VDC, 0.54 A, PoE+ (WAN)
- PoE: 1x PoE+ 802.3af/at (WAN)
- Uart: GND RX TX VCC - J2 (GND near WAN)
- Board silkscreen: "WVRTM-130ACN_V01" "19K-515-4500R" "RoHS" "2112"
Enable access to uboot menu (needed in wvrtm-130acn):
- The access to uboot menu is blocked by `bootdelay = 0` set in ubootenv.
With stock firmware version 01.01.02.163 and previous, you can use CVE 2020-24365
command injection https://nvd.nist.gov/vuln/detail/CVE-2020-24365
python3 exploit.py -t 192.168.1.1 -c "fw_setenv bootdelay 3; fw_saveenv"
Backup the stock firmware:
- Connect via uart
- Connect via ethernet and assign your pc the address 192.168.15.x/24
- Power on the device; and start typing '4' to enter uboot menu
- Set factory mode and boot
MT7621 # setenv factory 2; saveenv
MT7621 # nand read 2800000 2000000 81000000; bootm
- Telnet and copy all mtd blocks
telnet 192.168.15.1
- Copy all mtd blocks and start webserver
for N in $(seq 0 6); do dd if=/dev/mtd$N of=/tmp/eeprom_mtd$N.bin; done
mount -o bind /tmp /www
lighttpd -f /etc/lighttpd.conf
- Backup stock rootfs_data (optional)
dd if=/dev/mtd7 of=/tmp/eeprom_mtd7.bin
dd if=/dev/mtd8 of=/tmp/eeprom_mtd8.bin
- Download to your pc from http://192.168.15.1/eeprom_mtd$N.bin
Installation:
- Connect via uart
- Connect via ethernet and assign your pc the address 10.10.10.3/24
- Start a tftp server and serve the image initramfs-kernel.bin
mkdir /tmp/ftpd;
cp initramfs-kernel.bin /tmp/ftpd/kernel.bin
dnsmasq --enable-tftp --tftp-root=/tmp/ftpd
- Power on the device; and start typing '4' to halt the bootloader
- Change the active mtd partition from mtd6 to mtd5 (needed by uboot)
MT7621 # setenv mtddevnum 5; saveenv
- Write the openwrt initramfs in ram via tftp and boot it
MT7621 # tftpboot 81000000 kernel.bin; bootm
- From the initramfs create the ubi device and install openwrt via sysupgrade
ubiformat /dev/mtd11 -y
sysupgrade -n -v /tmp/sysupgrade.bin
Recovery:
Restore the stock firmware from the backup of the mtd blocks
mtd write eeprom_mtd5.bin firmware
mtd write eeprom_mtd6.bin Kernel2
mtd write eeprom_mtd7.bin Storage1
mtd write eeprom_mtd8.bin Storage2
ubiformat /dev/mtd8 -y
reboot
Links to previous works on wvrtm-127acn:
https://github.com/digiampietro/hacking-gemtekhttps://forum.openwrt.org/t/add-support-for-gemtek-wvrtm-127acn-linkem-provider/168757
Signed-off-by: Samuele Longhi <agave@dracaena.it>
Link: https://github.com/openwrt/openwrt/pull/16685
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently eth1 (which is the first "lan" interface) doesn't work on this device.
During boot the following can be seen in logs:
```
[ 2.252804] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module
[ 2.266060] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 19
[ 2.277889] mtk_soc_eth 1e100000.ethernet eth1: mediatek frame engine at 0xbe100000, irq 19
...
[ 2.355157] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module
[ 2.390312] mt7530-mdio mdio-bus:1f: configuring for fixed/rgmii link mode
[ 2.398597] mt7530-mdio mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx
[ 2.403872] mt7530-mdio mdio-bus:1f eth1 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7530 PHY] (irq=21)
[ 2.416988] mtk_soc_eth 1e100000.ethernet eth0: error -17 registering interface eth1
[ 2.426973] mt7530-mdio mdio-bus:1f eth2 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7530 PHY] (irq=22)
[ 2.440996] mt7530-mdio mdio-bus:1f eth3 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7530 PHY] (irq=23)
[ 2.454405] mt7530-mdio mdio-bus:1f eth4 (uninitialized): PHY [mt7530-0:04] driver [MediaTek MT7530 PHY] (irq=24)
[ 2.467198] mtk_soc_eth 1e100000.ethernet eth0: entered promiscuous mode
[ 2.474117] DSA: tree 0 setup
...
[ 6.820998] mtk_soc_eth 1e100000.ethernet dsa: renamed from eth0
[ 6.919904] mtk_soc_eth 1e100000.ethernet wan: renamed from eth1
```
So the problem seems to be the fact that built-in gmacs get default
names (eth0/eth1) and are renamed after switch ports are initialized. This means
that when switch port with name `eth1` is brought up this name is still used by
gmac1 causing switch port's init to fail.
This patch just renames the ports to avoid name collision.
Note: this will break existing configs for this device because it renames all
the ports. This should not be major problem because this device doesn't have a
proper OEM image and is only flashable with serial access, meaning there should
not be many users.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15865
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware Specification:
SoC: Mediatek MT7621DAT (MIPS1004Kc 880 MHz, dual core)
RAM: 128 MB
Storage: 128 MB NAND flash
Ethernet: 5x 10/100/1000 Mbps LAN1,LAN2,LAN3,LAN4 & WAN
Wireless: 2.4GHz: Mediatek MT7603EN up to 300Mbps (802.11b/g/n MIMO 2x2)
Wireless: 5GHz: Mediatek MT7615N up to 1733Mbps (802.11n/ac MU-MIMO 4x4)
LEDs: Power (white & amber), Internet (white & amber)
LEDs: 2.4G (White), 5Ghz (White)
Buttons: WPS, Reset
USB: Front V3.0 & Rear V2.0
MAC Table
Label xx:xx:xx:xx:xx:38
LAN xx:xx:xx:xx:xx:39
2.4Ghz xx:xx:xx:xx:xx:3A
5Ghz xx:xx:xx:xx:xx:3C
WAN xx:xx:xx:xx:xx:38
Flash Instructions:
D-Link normal OEM firmware update page
1. upload OpenWRT factory.bin like any D-Link upgrade image
D-Link Fail Safe GUI:
1. Push and hold reset button (on the bottom of the device) until power led starts flashing (about 10 secs or so) while plugging in the power cable.
2. Give it ~30 seconds, to boot the fail safe GUI
3. Connect your client computer to LAN1 of the device
4. Set your client IP address manually to 192.168.0.2 / 255.255.255.0
5. Call the fail safe page for the device at http://192.168.0.1/
6. Use the provided fail safe web GUI to upload the factory.bin to the device
Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16269
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SoC: MediaTek MT7621
Flash: 16MB (Macronix MX25L12805D)
RAM: 128MB
Serial: As marked on PCB, baudrate is 57600, DO NOT CONNECT 3.3V!!!
Ethernet: 4x 10/100/1000 Mbps (3x LAN + WAN)
WIFI0: MT7615 2.4GHz 802.11b/g/n
WIFI1: MT7615 5GHz 802.11ac
Antennas: 6x external (3 per radio), non-detachable
LEDs: Programmable power-LED (blue-colored)
Buttons: Reset
INSTALLATION:
Get rootshell using insructions from https://gist.github.com/ZIKH26/18693c67ee7d2f8d2c60231b19194c37
Download and flash image
On computer:
python -m http.server
On router:
cd /tmp
wget http://:8000/factory.bin
mtd -r write factory.bin firmware
Device should reboot at this point.
Reverting to stock:
Download archive with firmware from Ruijie's site and
get .bin file from it. Then write that binary to firmware
partition. After reboot, factory-reset the router using
reset button.
Signed-off-by: Yahor Leonenka <staryjakau@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16202
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ELECOM WSC-X1800GS is a 2.4/5 GHz band 11ax (Wi-Fi 6) mesh extender,
based on MT7621A
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 512 MiB (Nanya NT5CC256M16ER-EK)
- Flash : RAW-NAND 128 MiB (Winbond W29N01HVSINF)
- WLAN : 2.4/5 GHz 2T2R (MediaTek MT7915D + MT7975D)
- Ethernet : 2x 10/100/1000 Mbps
- switch : MediaTek MT7530 (SoC)
- LEDs/Keys (GPIO): 9x/2x
- UART : through-hole on PCB ("J4")
- arrangement : 3.3V, GND, TX, RX from tri-angle marking
- settings : 115200n8
- Power : 12 VDC, 1 A (Max. 10.5 W)
Flash instruction using initramfs-factory image
1. Boot WMC-X1800GST normally
2. Access to "http://192.168.2.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt initramfs-factory image and click apply ("適用")
button
4. On initramfs image, download sysupgrade image to the device and
perform sysupgrade with that image
5. Wait ~120 seconds to complete flashing
Notes:
- The "firmware" partition on the stock image is only 0xF00000 (15 MiB)
and it's too small for the current OpenWrt firmware with UBI format.
So use the unused area at the end of NAND flash for rootfs (UBI).
MAC addresses:
LAN : 04:AB:18:xx:xx:6E (Factory, 0x3fff4 (hex))
2.4 GHz: 04:AB:18:xx:xx:6F (Factory, 0x3fffa (hex))
5 GHz : 04:AB:18:xx:xx:70 (Factory, 0x4 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16384
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ELECOM WMC-X1800GST is a 2.4/5 GHz band 11ax (Wi-Fi 6) mesh router,
based on MT7621A
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 512 MiB (Nanya NT5CC256M16ER-EK)
- Flash : RAW-NAND 128 MiB (Winbond W29N01HVSINF)
- WLAN : 2.4/5 GHz 2T2R (MediaTek MT7915D + MT7975D)
- Ethernet : 3x 10/100/1000 Mbps
- switch : MediaTek MT7530 (SoC)
- LEDs/Keys (GPIO): 9x/5x
- UART : through-hole on PCB ("J4")
- arrangement : 3.3V, GND, TX, RX from tri-angle marking
- settings : 115200n8
- Power : 12 VDC, 1 A (Max. 11.5 W)
Flash instruction using initramfs-factory image
1. Boot WMC-X1800GST normally with "Router" mode
2. Access to "http://192.168.2.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt initramfs-factory image and click apply ("適用")
button
4. On initramfs image, download sysupgrade image to the device and
perform sysupgrade with that image
5. Wait ~120 seconds to complete flashing
Notes:
- The "firmware" partition on the stock image is only 0xF00000 (15 MiB)
and it's too small for the current OpenWrt firmware with UBI format.
So use the unused area at the end of NAND flash for rootfs (UBI).
MAC addresses:
LAN : 04:AB:18:xx:xx:BF (Factory, 0x3fff4 (hex))
WAN : 04:AB:18:xx:xx:C0 (Factory, 0x3fffa (hex))
2.4 GHz: 04:AB:18:xx:xx:C1 (Factory, 0x4 (hex))
5 GHz : 04:AB:18:xx:xx:C2
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16384
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for netis N6 WiFi 6 router.
Specification
-------------
- SoC : MediaTek MT7621AT, MIPS, 880 MHz
- RAM : 256 MiB
- Flash : NAND 128 MiB (ESMT PSU1GA30DT)
- WLAN : MT7905DAN + MT7975DN
- 2.4 GHz : b/g/n/ax, 574 Mbps, MIMO 2x2
- 5 GHz : a/n/ac/ax, 1201 Mbps, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x5 (1x WAN, 4x LAN)
- USB : 1x 3.0
- UART : 3.3V, 115200n8
- Buttons : 1x Reset
1x WPS
- LEDs : 1x Power (green)
1x System (green)
1x WAN (green)
1x WiFi 2.4 GHz (green), controlled by phy
1x WiFi 5 GHz (green), controlled by phy
1x WPS (green)
1x USB (green)
5x ethernet leds (green), controlled by switch
- Power : 12 VDC, 1.5 A
Installation
------------
1. Update the router using stock firmware web interface and OpenWrt
factory.bin image.
Recovery and return to stock
----------------------------
1. Assign your PC a static IP 192.168.1.2 and connect to the router using
the ethernet cable;
2. Power off the router;
3. Press Reset button, power on the router and wait until ethernet led
start blinking;
4. Release the button;
5. Open http://192.168.1.1/ (N6 System Recovery Mode) in your browser;
6. Upload OpenWrt factory.bin (or stock firmware *.bin) image and proceed
with upgrade.
MAC addresses
-------------
+---------+-------------------+
| | MAC example |
+---------+-------------------+
| LAN | dc:xx:xx:49:xx:04 |
| WAN | dc:xx:xx:49:xx:05 |
| WLAN 2g | dc:xx:xx:19:xx:06 |
| WLAN 5g | dc:xx:xx:79:xx:06 |
+---------+-------------------+
The WLAN MAC prototype was found in 'Factory', 0x4
The LAN MAC was found in 'Factory', 0x7ef20
The WAN MAC was found in 'Factory', 0x7ef26
Known issue
-----------
2.4 GHz WLAN doesn't start with mt76 driver.
Probable reason:
Original Netis N6 EEPROM contains wrong MT_EE_WIFI_CONF value (0xd2).
Other routers with the same WLAN hardware (e.g., Routerich AX1800)
have MT_EE_WIFI_CONF = 0x92.
Workaround (already included in this commit):
Extract EEPROM to a file at the first time boot and change
MT_EE_WIFI_CONF (offset 0x190) value from 0xd2 to 0x92. See
/etc/hotplug.d/firmware/11-mt76-caldata for details.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16322
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This files are executable:
target/linux/ramips/dts/mt7621_openfi_5pro.dts
target/linux/ramips/dts/mt7621_winstars_ws-wn536p3.dts
Has to be fixed.
Fixes: 5560791 ("ramips: add support for OpenFi 5Pro Travel Router")
Fixes: 2da2705 ("ramips: add support for WINSTARS WS-WN536P3")
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16322
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specifications:
- Device: DNA Valokuitu Plus EX400
- SoC: MT7621A
- Flash: 256MB NAND
- RAM: 256MB
- Ethernet: Built-in, 2 x 1GbE
- Wifi: MT7603 2.4 GHz, MT7615 5 GHz (4x internal antennas)
- USB: 1x 3.0
- LED: 1x green/red, 1x green
- Buttons: Reset
MAC addresses:
- LAN: u-boot 'ethaddr' (label)
- WAN: label + 1
- 2.4 GHz: label + 6
- 5 GHz: label + 7
Serial:
There is a black block connector next to the red ethernet connector. It
is accessible also through holes in the casing.
Pinout (TTL 3.3V)
+---+---+
|Tx |Rx |
+---+---+
|Vcc|Gnd|
+---+---+
Firmware:
The vendor firmware is a fork of OpenWrt (Reboot) with a kernel version
4.4.93. The flash is arranged as below and there is a dual boot
mechanism alternating between rootfs_0 and rootfs_1.
+-------+------+------+-----------+-----------+
| | env1 | env2 | rootfs_0 | rootfs_1 |
| +------+------+-----------+-----------+
| | UBI volumes |
+-------+-------------------------------------+
|U-Boot | UBI |
+-------+-------------------------------------+
|mtd0 | mtd1 |
+-------+-------------------------------------+
| NAND |
+---------------------------------------------+
In OpenWrt rootfs_0 will be used as a boot partition that will contain the
kernel and the dtb. The squashfs rootfs and overlay are standard OpenWrt
behaviour.
+-------+------+------+-----------+--------+------------+
| | env1 | env2 | rootfs_0 | rootfs | rootfs_data|
| +------+------+-----------+--------+------------+
| | UBI volumes |
+-------+-----------------------------------------------+
|U-Boot | UBI |
+-------+-----------------------------------------------+
|mtd0 | mtd1 |
+-------+-----------------------------------------------+
| NAND |
+-------------------------------------------------------+
U-boot:
With proper serial access booting can be halted to U-boot by pressing any
key. TFTP and flash writes are available, but only the first one has been
tested.
NOTE: Recovery mode can be accessed by holding down the reset button while
powering on the device. The led 'Update' will show a solid green light
once ready. A web server will be running at 192.168.1.1:80 and it will
allow flashing a firmware package. You can cycle between rootfs_0 and
rootfs_1 by pressing the reset button once.
Root password:
With the vendor web UI create a backup of your settings and download the
archive to your computer. Within the archive in the file
/etc/shadow replace the password hash for root with that of a password you
know. Restore the configuration with the vendor web UI and you will have
changed the root password.
SSH access:
You might need to enable the SSH service for LAN interface as by default
it's enabled for WAN only.
Installing OpenWrt:
With the vendor web UI install the OpenWrt factory image. Alternatively,
ssh to the device and use sysupgrade -n from cli.
Finalize by installing the OpenWrt sysupgrade image to get a fully
functioning system.
Reverting to the vendor firmware:
Boot with OpenWrt initramfs image
- Remove volumes rootfs_0, rootfs and rootfs_data and create vendor
volumes.
ubirmvol /dev/ubi0 -n 2
ubirmvol /dev/ubi0 -n 3
ubirmvol /dev/ubi0 -n 4
ubimkvol /dev/ubi0 -N rootfs_0 -S 990
ubimkvol /dev/ubi0 -N rootfs_1 -S 990
Power off and enter to the U-boot recovery to install the vendor
firmware.
Known issues:
- MACs for wifi are stored in currently unknown place but it seems
to persist over power-off. They might be stored on the chip.
Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
[rmilecki: try NVMEM for MACs]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Add missing 'model' string to DT, so /tmp/sysinfo/model gets populated.
Fixes: e497c975d3 ("ramips: mt76x8: add support for Yuncore M300")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add missing 'model' string to DT, so /tmp/sysinfo/model gets populated.
Fixes: 64dae1052b ("ramips: mt76x8: add support for Yuncore CPE200")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
