Correctly load the list of basic_rates from UCI. basic-rates shall be
stored as a option-list. The current code did not retrieve this list
correctly.
wpa_supplicant uses a different config option to set basic-rates
when operating in mesh-mode.
Use the correct config key and calculation for mesh-interfaces.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit a854d833ea)
For WIFI7 devices (such as mt7925e), the dev width is currently
always "20 MHz (no HT)" in monitor mode.
Add EHT and HE160 support to iw_htmode to fix this issue.
Additionally, the following changes are made:
1. Set iw_htmode to 160MHz for VHT160. The reason for the current
VHT160 setting is unclear and seems to have been in place for
over a decade (ibss_htmode [1]). If anyone knows its impact,
please inform me so I can restore it.
2. Modify MHZ to MHz. The original matching table in the current
iw tool uses MHz. Although the match is case-insensitive,
correcting this won't hurt.
[1]: 768d09be87
Signed-off-by: Ming Kuang <ming@imkuang.com>
Link: https://github.com/openwrt/openwrt/pull/18319
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 86eb1c0b5a)
Bringing up a mesh interface using wpa_supplicant already supports a
per-VIF basic rate selection. Add the same ability when creating a mesh
VIF without wpa_supplicant.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 3deeb7805f)
This can be used to configure the base mac address from which all
interface mac addresses are derived
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 00860e485b)
Simplifies setting ifname to a different pattern for all affected
interfaces.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit a9ff3ba24b)
Basic rates were not set for mesh-interfaces, resulting in the undesired
behavior where 11s frames might be sent with a rate which was not
configured.
Depending on the driver, the basic rate might also be used to determine
the beacon rate configured to the chip. One such example are MediaTek
MT7915 platforms.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 3ec7f3a512)
On some drivers, setting the tx power on the interface is not enough.
Set it for the phy as well.
Fixes: 04fb05914e ("wifi-scripts: add multi-radio config support")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit b795e5cbcf)
Regarding SAE support in wifi-station:
Important Note: Unlike PSK wifi-stations, both `mac` and `key` options are required
to make it work. With PSK, hostapd used to perform a brute-force match to find which
PSK entry to use, but with SAE this is infeasible due to SAE's design.
When `mac` is omitted, it will allow any MAC address to use the SAE password if it
didn't have a MAC address assigned to it, but this could only be done once.
The last wildcard entry would be used.
Also, unlike "hostapd: add support for SAE in PPSK option" (commit 913368a),
it is not required to set `sae_pwe` to `0`. This gives it a slight advantage
over using PPSK that goes beyond not needing RADIUS.
Example Configuration:
```
config wifi-vlan
option iface default_radio0
option name 999
option vid 999
option network management
config wifi-station
# Allow user with MAC address 00:11:22:33:44:55 and matching
# key "secretadminpass" to access the management network.
option iface default_radio0
option vid 999
option mac '00:11:22:33:44:55'
option key secretadminpass
config wifi-vlan
option iface default_radio0
option name 100
option vid 100
option network guest
config wifi-station
# With SAE, when 'mac' is omitted it will be the fallback in case no
# other MAC address matches. It won't be possible for a user that
# has a matching MAC to use this network (i.e., 00:11:22:33:44:55
# in this example).
option iface default_radio0
option vid 100
option key guestpass
```
Regarding PSK file creation optimization:
This patch now conditionally runs `hostapd_set_psk_file` depending on `auth_type`.
Previously, `hostapd_set_psk` would always execute `hostapd_set_psk_file`, which
would create a new file if `wifi-station` was in use even if PSK was not enabled.
This change checks the `auth_type` to ensure that it is appropriate to parse the
`wifi-station` entries and create those files.
Furthermore, we now only configure `wpa_psk_file` when it is a supported option
(i.e., psk or psk-sae is used). Previously, we used to configure it when it was
not necessary. While it didn't cause any issues, it would litter `/var/run` with
unnecessary files. This patch fixes that case by configuring it depending on the
`auth_type`.
The new SAE support is aligned with these PSK file changes.
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/17145
Signed-off-by: John Crispin <john@phrozen.org>
(cherry picked from commit 65a1c666f2)
Link: https://github.com/openwrt/openwrt/pull/17248
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Don't fail wireless interface bringup on empty PSK set. This is a valid
configuration, resulting in a PSK network which can't be connected to.
It does not fail the bringup of the hostapd process.
Keep failing the interface setup in case a password with invalid length
is used.
This is also beneficial when intending to configure a PPSK network. It
allows to create a network where no PPSK is yet set.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 17a71f0c154cebd2e52cd8407531a9a88c931474)
The initialization of mesh interfaces currently fail when wpa_supplicant
is not installed. This is due to the script calling the wpa_supplicant
feature indicator without verifying wpa_supplicant is installed at all.
To avoid failing, first check if wpa_supplicant is installed before
determining the available featureset.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 1be18c6daa)
Fixup capabilities parsing in iw output.
In addition to the normal capabilities iw now also outputs HE MAC, HE
PHY and EHT MAC and EHT PHY capabilities. Exclude them in the parsing.
The grep returns this with mac80211-hwsim:
```
root@OpenWrt:~# iw phy phy0 info | grep 'Capabilities:'
Capabilities: 0x107e
HE PHY Capabilities: (0x02bfce0000000000000000):
EHT PHY Capabilities: (0x7c0000feffff7f01):
HE PHY Capabilities: (0x02bfce0000000000000000):
EHT PHY Capabilities: (0x7c0000feffff7f01):
HE PHY Capabilities: (0x02bf000000000000000000):
Capabilities: 0x107e
HE PHY Capabilities: (0x1cbfce0000000000000000):
EHT PHY Capabilities: (0xfc1f3ffeffff7f37):
HE PHY Capabilities: (0x1cbfce0000000000000000):
EHT PHY Capabilities: (0xfc1f3ffeffff7f37):
HE PHY Capabilities: (0x1cbf000000000000000000):
HE PHY Capabilities: (0x1cbfce0000000000000000):
EHT PHY Capabilities: (0xfefffffeffffff7f):
HE PHY Capabilities: (0x1cbfce0000000000000000):
EHT PHY Capabilities: (0xfefffffeffffff7f):
HE PHY Capabilities: (0x1cbf000000000000000000):
Capabilities: 0x107e
```
With busybox 1.36.1 the ht_cap_mask variable will be set to
-72057598332895361. With busybox 1.37.0 it will be set to -1.
Both values are wrong, after this change it will be set to 4222
(0x107E).
Link: https://github.com/openwrt/openwrt/pull/17043
(cherry picked from commit adf958c919)
Link: https://github.com/openwrt/openwrt/pull/17055
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This allows annotating wifi interfaces in the config in a way that can be
queried through wifi status. One example use case is to mark wifi interfaces
for use with specific services without having to explicitly reference the
(often unnamed) sections from elsewhere.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit a3ec35cadb)
This patch fixes the list delimiter between 3GPP networks
passed to hostapd.
> list iw_anqp_3gpp_cell_net '262,001'
> list iw_anqp_3gpp_cell_net '262,002'
When passing a list of "iw_anqp_3gpp_cell_net" parameters via UCI,
hostapd would crash at startup:
> daemon.err hostapd: Line 73: Invalid anqp_3gpp_cell_net: 262,001:262,002
Using a semicolon as a delimiter, hostapd will start as expected.
Signed-off-by: Sarah Maedel <git@tbspace.de>
Without this configuration it is not possible to run the radio using HE160 on channels 149-177.
Fixes: #14906
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
With mac80211_hwsim I have seen such entries in OpenWrt 22.03:
HE Iftypes: managed, AP
The mac80211.sh script did not detect the entry and failed. Allow
arbitrary other entries before to fix this problem.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
