Some regression were reported with the backported upstream version. Old
kernel require an additional flush in some case and this was handled in
the old downstream patch.
Reintroduce the flush to fix the regression and refresh affected patch.
Fixes: f63d64ede0 ("generic: move patch from pending to backport")
Link: https://github.com/openwrt/openwrt/pull/18501
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The ATS SFP GT-T quirk patch was backported to stable kernel 6.6 but
was not notice while bumping the kernel version as they listed the quirk
at the bottom of the SFP quirk table while our hack patch put it at the
top.
With migrating to the upstream version, the duplication was made more
apparent.
Drop the double entry for the SFP module as it's already there and not
needed and refresh patches.
Link: https://github.com/openwrt/openwrt/pull/18484
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Replace ARM gc sections patch with upstream version. It seems this
feature is finally supported upstream with some minor difference.
In theory the upstream version should cut even more stuff, this really
needs to be evaluated if it's OK also to handle regression with the
kernel 6.12 update.
Link: https://github.com/openwrt/openwrt/pull/18464
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Move all patch that got merged upstream from pending to backport and add
related tag. This is to make it easier to update to kernel 6.12.
Patch 680 required some special care as the upstream version had to be
split in a series of 6 patch.
Referesh all affected patch.
Link: https://github.com/openwrt/openwrt/pull/18464
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
QCOM SPI NAND driver got merged upstream hence we can drop the special
patch from qualcommax and qualcommbe target and move them to the generic
backports directory to reduce patch maintenance.
While at it refresh any affected patch and target and also backport other
minor fixup for the SPI NAND driver merged upstream later.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Sync jitterentropy source code with linux-6.12 to solve the
issue of jitterentropy initialization failed:
[ 9.523489] jitterentropy: Initialization failed with host not compliant with requirements: 9
[ 9.661916] kmodloader: 1 module could not be probed
[ 9.662377] kmodloader: - jitterentropy_rng - 0
In linux upstream commit cf27d9475f37 ("crypto: jitter - use
permanent health test storage"), when FIPS crypto is disabled,
the health test results are always explicitly skipped. That means
it will never return error code 9 (health test failed) again.
Fixes: https://github.com/openwrt/openwrt/issues/16684
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18399
Signed-off-by: Robert Marko <robimarko@gmail.com>
Bridge port isolation offload support has been added to the bridge core
and many DSA drivers. mt7530 support was backported in OpenWrt commit
c4e6a147a6 ("generic: 6.6: mt7530: add support for bridge port
isolation").
Backport qca8k support as well.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Link: https://github.com/openwrt/openwrt/pull/18375
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
After booting, a "transmit queue 0 timed out" warning followed by a
register dump was observed. The dump indicates that mtk_hw_init() does
not initialize the EEECR during probe. This occurs because the
netdev is allocated in mtk_add_mac(), which is called after
mtk_hw_init(). Consequently, the EEECR register remains uninitialized
until a reset is triggered, causing mtk_hw_init() to run again with a
valid netdev, at which point the register is finally set.
To address this, instead of modifying the probe sequence, latch the Tx
LPI enable state and timer value, and move the EEECR register
initialization to mtk_mac_link_up() to ensure proper setup when the
interface comes up.
Additionally, the splat reveals that LPI functionality is controlled by
the MAC_MCR_EEE bits in the MCR register. Update mtk_set_eee() to
modify these bits accordingly.
Fixes: d8315d5358 ("kernel: backport Mediatek SoC EEE support")
Fixes: edddbaf79c ("kernel: Mediatek: set default EEE Tx LPI timer")
Signed-off-by: Qingfang Deng <dqfext@gmail.com>
Currently, if the phy driver does not implement the led_brightness_set
function, setting the LED will result in the following error message:
leds mdio-bus:*:green:lan: Setting an LED's brightness failed (-524)
Backport a patch to silence this error message.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/18080
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes the handling of some FS copper SFP modules using the RollBall
protocol and needing some extra treatment.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Due to API changes during the backport, the default value of Tx LPI
timer is accidentally left unset, breaking the network if EEE is on.
Set the default timer to 1ms on init, and fix an incorrect condition.
Fixes: d8315d5358 ("kernel: backport Mediatek SoC EEE support")
Signed-off-by: Qingfang Deng <dqfext@gmail.com>
Backport Mediatek SoC EEE support from net-next upstream.
Signed-off-by: Qingfang Deng <dqfext@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[refreshed patches]
Add missing patch description, so all generic patches can be applied
to a kernel tree using 'git am'.
Fixes: d23e0a0086 ("kernel: backport MHI patch required by an upcoming mac80211 update")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Uses upstream DSA switch modules (rtl8365mb, rtl8366), similar to
RTL8367C and rtl8366rb swconfig drivers.
The package dependencies exclude targets built without kernel CONFIG_OF.
It also fixes the rtl8366rb LED support.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
b11bff90f2ad r8169: add support for RTL8125BP rev.b
b3593df26ab1 r8169: add support for RTL8125D rev.b
b299ea006928 r8169: adjust version numbering for RTL8126
bb18265c3aba r8169: remove support for chip version 11
2e20bf8cc057 r8169: remove unused flag RTL_FLAG_TASK_RESET_NO_QUEUE_WAKE
e340bff27e63 r8169: copy vendor driver 2.5G/5G EEE advertisement constraints
The EEE advertisement patch has been reworked for linux v6.6 because
phy_set_eee_broken() is only present on linux >= v6.13 and eee_broken_modes
declaration has been converted to a bitmap, so linkmode_set_bit() can't be
used either.
e340bff27eed623fb8e3721aa69e70
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Expose the temperature sensor built-into RTL822x 2.5G and 5G PHYs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Some VRX518 modems fail to initialize properly with the error message
"dc_ep_clk_on failed". As a result, the DSL data path doesn't work.
This hack, which is based on code from the FRITZ!Box 7530 GPL archive,
fixes the issue. It changes the PCIe vendor/device ID to values matching
a Lantiq SoC. It also appears to emulate a Lantiq CPU ID register for
connected PCIe devices, by remapping the matching address area to a
specially crafted buffer using the address translation unit.
A dedicated compatible is created to activate this in
the device tree, so this shouldn't affect any devices other than
FRITZ!Box 7530/7520.
Original investigation was done in 59f5212517 which used the "avm,host_magic" property to enabled the patch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/17622
Signed-off-by: Robert Marko <robimarko@gmail.com>
The patch adding temperature sensor support for r8169 has been removed upstream
and the functionality will be added to Realtek PHY instead:
1f691a1fc4
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
7a3bcd39ae1f r8169: use helper r8169_mod_reg8_cond to simplify rtl_jumbo_config
e3e9e9039fa6 r8169: align WAKE_PHY handling with r8125/r8126 vendor drivers
330dc2297c82 r8169: improve rtl_set_d3_pll_down
c507e96b5763 r8169: improve __rtl8169_set_wol
83cb4b470c66 r8169: remove leftover locks after reverted change
2cd02f2fdd8a r8169: improve initialization of RSS registers on RTL8125/RTL8126
a3d8520e6a19 r8169: align RTL8126 EEE config with vendor driver
4af2f60bf737 r8169: align RTL8125/RTL8126 PHY config with vendor driver
eb90f876b796 r8169: align RTL8125 EEE config with vendor driver
b8bd8c44a266 r8169: fix inconsistent indenting in rtl8169_get_eth_mac_stats
f75d1fbe7809 r8169: add support for RTL8125D
c4e64095c00c r8169: enable EEE at 2.5G per default on RTL8125B
d64113c6bb5e r8169: remove rtl_dash_loop_wait_high/low
1c105bacb160 r8169: avoid duplicated messages if loading firmware fails and switch to warn level
ac48430368c1 r8169: don't take RTNL lock in rtl_task()
e3fc5139bd8f r8169: implement additional ethtool stats ops
b8bf38440ba9 r8169: enable SG/TSO on selected chip versions per default
854d71c555df r8169: remove original workaround for RTL8125 broken rx issue
1ffcc8d41306 r8169: add support for the temperature sensor being available from RTL8125B
The following patches require backporting additional linux patches:
e2015942e90a r8169: replace custom flag with disable_work() et al
e340bff27e63 r8169: copy vendor driver 2.5G/5G EEE advertisement constraints
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Conversion to DSA broke 802.2+LLC+SNAP packet processing. Frames
received by napi_complete_done with GRO and DSA have transport_header
set two bytes short, or pointing 2 bytes before network_header &
skb->data. As snap_rcv expects transport_header to point to SNAP
header (OID:PID) after LLC processing advances offset over LLC header
(llc_rcv & llc_fixup_skb), code doesn't find a match and packet is
dropped.
Image built at this commit operates properly:
86dadeba48 - generic: add patch for GPON-ONU-34-20BI quirk
Image built at following commit exhibits the issue:
337e36e0ef - ipq806x: convert each device to DSA implementation
As issue is LLC specific, to avoid impacting non-LLC traffic, and to
follow up on original assumption made on kernel commit fda55eca5a33
("net: introduce skb_transport_header_was_set()") stating "network
stacks usually reset the transport header anyway", llc_fixup_skb to
reset and advance the offset. llc_fixup_skb already assumes the LLC
header is at skb->data, and by definition SNAP header immediately
follows.
Signed-off-by: Antonio Pastor <antonio.pastor@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17220
Signed-off-by: Robert Marko <robimarko@gmail.com>
This backport patch inserted suspend/resume callbacks
for the wrong PHY driver.
The fixed patch is needed for Huawei AP5030DN
to initialize its second PHY.
Refresh all affected patch with make target/linux/refresh.
Fixes: 06cdc07f8c ("ath79: add support for Huawei AP5030DN")
Signed-off-by: Marco von Rosenberg <marcovr@selfnet.de>
Link: https://github.com/openwrt/openwrt/pull/17312
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
