3e15a54bb0
It's a 4G Cat.20 router used by Vodafone Italy (called Vodafone FWA)
and Vodafone DE\T-Mobile PL (called GigaCube).
Modem is a MiniPCIe-to-USB based on Snapdragon X24,
it supports 4CA aggregation.
There are currently two hardware revisions, which
differ on the 5Ghz radio:
AT1 = QCA9984 5Ghz Radio on PCI-E bus
AT2 = IPQ4019 5Ghz Radio inside IPQ4019 like 2.4Ghz
Device specification
--------------------
SoC Type: Qualcomm IPQ4019
RAM: 256 MiB
Flash: 128 MiB SPI NAND (Winbond W25N01GV)
ROM: 2MiB SPI Flash (GD25Q16)
Wireless 2.4 GHz (IP4019): b/g/n, 2x2
Wireless 5 GHz:
(QCA9984): a/n/ac, 4x4 HW REV AT1
(IPA4019): a/n/ac, 2x2 HW REV AT2
Ethernet: 2xGbE (WAN/LAN1, LAN2)
USB ports: No
Button: 2 (Reset/WPS)
LEDs: 3 external leds: Network (white or red), Wifi, Power and 1 internal (blue)
Power: 12 VDC, 1 A
Connector type: Barrel
Bootloader: U-Boot
Installation
------------
1. Place OpenWrt initramfs image for the device on a TFTP
in the server's root. This example uses Server IP: 192.168.0.2
2. Connect serial console (115200,8n1) to serial connector
GND (which is right next to the thing with MF289F MIMO-V1.0), RX, TX
(refer to this image: https://ibb.co/31Gngpr).
3. Connect TFTP server to RJ-45 port (WAN/LAN1).
4. Stop in u-Boot (using ESC button) and run u-Boot commands:
setenv serverip 192.168.0.2
setenv ipaddr 192.168.0.1
set fdt_high 0x85000000
tftp openwrt-ipq40xx-generic-zte_mf289f-initramfs-fit-zImage.itb
bootm $loadaddr
5. Please make backup of original partitions, if you think about revert to
stock, specially mtd16 (Web UI) and mtd17 (rootFS).
Use /tmp as temporary storage and do:
WEB PARITION
--------------------------------------
cat /dev/mtd16 > /tmp/mtd16.bin
scp /tmp/mtd16.bin root@YOURSERVERIP:/
rm /tmp/mtd16.bin
ROOT PARITION
--------------------------------------
cat /dev/mtd17 > /tmp/mtd17.bin
scp /tmp/mtd17.bin root@YOURSERVERIP:/
rm /tmp/mtd17.bin
6. Login via ssh or serial and remove stock partitions
(default IP 192.168.0.1):
# this can return an error, if ubi was attached before
# or rootfs part was erased before.
ubiattach -m 17
# it could return error if rootfs part was erased before
ubirmvol /dev/ubi0 -N ubi_rootfs
# some devices doesn't have it
ubirmvol /dev/ubi0 -N ubi_rootfs_data
7. download and install image via sysupgrade -n
(either use wget/scp to copy the mf289f's squashfs-sysupgrade.bin
to the device's /tmp directory)
sysupgrade -n /tmp/openwrt-...-zte_mf289f-squashfs-sysupgrade.bin
Sometimes it could print ubi attach error, but please ignore it
if process goes forward.
Flash Layout
NAND:
mtd8: 000a0000 00020000 "fota-flag"
mtd9: 00080000 00020000 "0:ART"
mtd10: 00080000 00020000 "mac"
mtd11: 000c0000 00020000 "reserved2"
mtd12: 00400000 00020000 "cfg-param"
mtd13: 00400000 00020000 "log"
mtd14: 000a0000 00020000 "oops"
mtd15: 00500000 00020000 "reserved3"
mtd16: 00800000 00020000 "web"
mtd17: 01d00000 00020000 "rootfs"
mtd18: 01900000 00020000 "data"
mtd19: 03200000 00020000 "fota"
mtd20: 0041e000 0001f000 "kernel"
mtd21: 0101b000 0001f000 "ubi_rootfs"
SPI:
mtd0: 00040000 00010000 "0:SBL1"
mtd1: 00020000 00010000 "0:MIBIB"
mtd2: 00060000 00010000 "0:QSEE"
mtd3: 00010000 00010000 "0:CDT"
mtd4: 00010000 00010000 "0:DDRPARAMS"
mtd5: 00010000 00010000 "0:APPSBLENV"
mtd6: 000c0000 00010000 "0:APPSBL"
mtd7: 00050000 00010000 "0:reserved1"
Back to Stock (!!! need original dump taken from initramfs !!!)
-------------
1. Place mtd16.bin and mtd17.bin initramfs image
for the device on a TFTP in the server's root.
This example uses Server IP: 192.168.0.2
2. Connect serial console (115200,8n1) to serial console
connector (refer to the pin-out from above).
3. Connect TFTP server to RJ-45 port (WAN/LAN1).
4. rename mtd16.bin to web.img and mtd17.bin to root_uImage_s
5. Stop in u-Boot (using ESC button) and run u-Boot commands:
This will erase RootFS+Web:
nand erase 0x1000000 0x800000
nand erase 0x1800000 0x1D00000
This will restore RootFS:
tftpboot 0x84000000 ${dir}root_uImage_s
nand erase 0x1800000 0x1D00000
nand write $fileaddr 0x1800000 $filesize
This will restore Web Interface:
tftpboot 0x84000000 ${dir}web.img
nand erase 0x1000000 0x800000
nand write $fileaddr 0x1000000 $filesize
After first boot on stock firwmare, do a factory reset.
Push reset button for 5 seconds so all parameters will
be reverted to the one printed on label on bottom of the router
Signed-off-by: Giammarco Marzano <stich86@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@gmail.com>
(Warning: commit message did not conform to UTF-8 - hopefully fixed?,
added description of the pin-out if image goes down, reformatted
commit message to be hopefully somewhat readable on git-web,
redid some of the gpio-buttons & leds DT nodes, etc.)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 0de6a3339f)
[Backported to 22.03: added DTS to the makefile patch, fixed ipq-wifi
inclusion for MF286D]
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
439 lines
7.5 KiB
Plaintext
439 lines
7.5 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
// Copyright (c) 2022, Pawel Dembicki <paweldembicki@gmail.com>.
|
|
// Copyright (c) 2022, Giammarco Marzano <stich86@gmail.com>.
|
|
|
|
#include "qcom-ipq4019.dtsi"
|
|
#include <dt-bindings/soc/qcom,tcsr.h>
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
#include <dt-bindings/leds/common.h>
|
|
|
|
/ {
|
|
model = "ZTE MF289F";
|
|
compatible = "zte,mf289f";
|
|
|
|
aliases {
|
|
led-boot = &led_status;
|
|
led-failsafe = &led_status;
|
|
led-running = &led_status;
|
|
led-upgrade = &led_status;
|
|
};
|
|
|
|
chosen {
|
|
/*
|
|
* bootargs forced by u-boot bootipq command:
|
|
* 'ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait'
|
|
*/
|
|
bootargs-append = " root=/dev/ubiblock0_1";
|
|
};
|
|
|
|
/*
|
|
* This node is used to restart modem module to avoid anomalous
|
|
* behaviours on initial communication.
|
|
*/
|
|
gpio-restart {
|
|
compatible = "gpio-restart";
|
|
gpios = <&tlmm 8 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_status: led-0 {
|
|
label = "blue:power";
|
|
function = LED_FUNCTION_POWER;
|
|
color = <LED_COLOR_ID_BLUE>;
|
|
gpios = <&tlmm 10 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led-1 {
|
|
function = LED_FUNCTION_WLAN;
|
|
color = <LED_COLOR_ID_BLUE>;
|
|
gpios = <&tlmm 61 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
key-reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
key-wps {
|
|
label = "wps";
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
gpios = <&tlmm 68 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
soc {
|
|
ess-psgmii@98000 {
|
|
status = "okay";
|
|
};
|
|
|
|
tcsr@1949000 {
|
|
compatible = "qcom,tcsr";
|
|
reg = <0x1949000 0x100>;
|
|
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
|
|
};
|
|
|
|
tcsr@194b000 {
|
|
/* select hostmode */
|
|
compatible = "qcom,tcsr";
|
|
reg = <0x194b000 0x100>;
|
|
qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
|
|
status = "okay";
|
|
};
|
|
|
|
ess_tcsr@1953000 {
|
|
compatible = "qcom,tcsr";
|
|
reg = <0x1953000 0x1000>;
|
|
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
|
|
};
|
|
|
|
tcsr@1957000 {
|
|
compatible = "qcom,tcsr";
|
|
reg = <0x1957000 0x100>;
|
|
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
|
|
};
|
|
|
|
ess-switch@c000000 {
|
|
status = "okay";
|
|
};
|
|
|
|
edma@c080000 {
|
|
status = "okay";
|
|
};
|
|
};
|
|
};
|
|
|
|
&prng {
|
|
status = "okay";
|
|
};
|
|
|
|
&mdio {
|
|
status = "okay";
|
|
pinctrl-0 = <&mdio_pins>;
|
|
pinctrl-names = "default";
|
|
reset-gpios = <&tlmm 47 GPIO_ACTIVE_LOW>;
|
|
reset-delay-us = <2000>;
|
|
};
|
|
|
|
&watchdog {
|
|
status = "okay";
|
|
};
|
|
|
|
&blsp_dma {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb2 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb3 {
|
|
status = "okay";
|
|
};
|
|
|
|
&blsp1_spi1 {
|
|
pinctrl-0 = <&spi_0_pins>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>,
|
|
<&tlmm 54 GPIO_ACTIVE_HIGH>;
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
reg = <0>;
|
|
spi-max-frequency = <24000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "0:SBL1";
|
|
reg = <0x0 0x40000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "0:MIBIB";
|
|
reg = <0x40000 0x20000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@60000 {
|
|
label = "0:QSEE";
|
|
reg = <0x60000 0x60000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@c0000 {
|
|
label = "0:CDT";
|
|
reg = <0xc0000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@d0000 {
|
|
label = "0:DDRPARAMS";
|
|
reg = <0xd0000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@e0000 {
|
|
label = "0:APPSBLENV";
|
|
reg = <0xe0000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@f0000 {
|
|
label = "0:APPSBL";
|
|
reg = <0xf0000 0xc0000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@1b0000 {
|
|
label = "0:reserved1";
|
|
reg = <0x1b0000 0x50000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
|
|
spi-nand@1 { /* flash@1 ? */
|
|
compatible = "spi-nand";
|
|
reg = <1>;
|
|
spi-max-frequency = <24000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "fota-flag";
|
|
reg = <0x0 0xa0000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@a0000 {
|
|
label = "ART";
|
|
reg = <0xa0000 0x80000>;
|
|
read-only;
|
|
compatible = "nvmem-cells";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
precal_art_1000: precal@1000 {
|
|
reg = <0x1000 0x2f20>;
|
|
};
|
|
|
|
precal_art_5000: precal@5000 {
|
|
reg = <0x5000 0x2f20>;
|
|
};
|
|
};
|
|
|
|
partition@120000 {
|
|
label = "mac";
|
|
reg = <0x120000 0x80000>;
|
|
read-only;
|
|
compatible = "nvmem-cells";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
macaddr_mac_0: macaddr@0 {
|
|
reg = <0x0 0x6>;
|
|
};
|
|
};
|
|
|
|
partition@1a0000 {
|
|
label = "reserved2";
|
|
reg = <0x1a0000 0xc0000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@260000 {
|
|
label = "cfg-param";
|
|
reg = <0x260000 0x400000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@660000 {
|
|
label = "log";
|
|
reg = <0x660000 0x400000>;
|
|
};
|
|
|
|
partition@a60000 {
|
|
label = "oops";
|
|
reg = <0xa60000 0xa0000>;
|
|
};
|
|
|
|
partition@b00000 {
|
|
label = "reserved3";
|
|
reg = <0xb00000 0x500000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@1000000 {
|
|
label = "web";
|
|
reg = <0x1000000 0x800000>;
|
|
};
|
|
|
|
partition@1800000 {
|
|
label = "rootfs";
|
|
reg = <0x1800000 0x1d00000>;
|
|
};
|
|
|
|
partition@3500000 {
|
|
label = "data";
|
|
reg = <0x3500000 0x1900000>;
|
|
};
|
|
|
|
partition@4e00000 {
|
|
label = "fota";
|
|
reg = <0x4e00000 0x3200000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&blsp1_uart1 {
|
|
pinctrl-0 = <&serial_pins>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
};
|
|
|
|
&crypto {
|
|
status = "okay";
|
|
};
|
|
|
|
&cryptobam {
|
|
status = "okay";
|
|
};
|
|
|
|
&gmac0 {
|
|
nvmem-cell-names = "mac-address";
|
|
nvmem-cells = <&macaddr_mac_0>;
|
|
};
|
|
|
|
&gmac1 {
|
|
nvmem-cell-names = "mac-address";
|
|
nvmem-cells = <&macaddr_mac_0>;
|
|
mac-address-increment = <1>;
|
|
};
|
|
|
|
|
|
&qpic_bam {
|
|
status = "okay";
|
|
};
|
|
|
|
&tlmm {
|
|
i2c_0_pins: i2c_0_pinmux {
|
|
mux {
|
|
pins = "gpio20", "gpio21";
|
|
function = "blsp_i2c0";
|
|
bias-disable;
|
|
};
|
|
};
|
|
|
|
mdio_pins: mdio_pinmux {
|
|
mux_1 {
|
|
pins = "gpio6";
|
|
function = "mdio";
|
|
bias-pull-up;
|
|
};
|
|
|
|
mux_2 {
|
|
pins = "gpio7";
|
|
function = "mdc";
|
|
bias-pull-up;
|
|
};
|
|
};
|
|
|
|
serial_pins: serial_pinmux {
|
|
mux {
|
|
pins = "gpio16", "gpio17";
|
|
function = "blsp_uart0";
|
|
bias-disable;
|
|
};
|
|
};
|
|
|
|
spi_0_pins: spi_0_pinmux {
|
|
pinmux {
|
|
function = "blsp_spi0";
|
|
pins = "gpio13", "gpio14", "gpio15";
|
|
drive-strength = <12>;
|
|
bias-disable;
|
|
};
|
|
|
|
pinmux_cs {
|
|
function = "gpio";
|
|
pins = "gpio12", "gpio54";
|
|
drive-strength = <2>;
|
|
bias-disable;
|
|
output-high;
|
|
};
|
|
};
|
|
};
|
|
|
|
&usb2_hs_phy {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb3_ss_phy {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb3_hs_phy {
|
|
status = "okay";
|
|
};
|
|
|
|
&wifi0 {
|
|
status = "okay";
|
|
nvmem-cell-names = "pre-calibration", "mac-address";
|
|
nvmem-cells = <&precal_art_1000>, <&macaddr_mac_0>;
|
|
mac-address-increment = <2>;
|
|
qcom,ath10k-calibration-variant = "zte,mf289f";
|
|
};
|
|
|
|
/* This node is used only on AT2 version for 5Ghz on IPQ4019 with board-id=21 */
|
|
&wifi1 {
|
|
status = "okay";
|
|
nvmem-cell-names = "pre-calibration", "mac-address";
|
|
nvmem-cells = <&precal_art_5000>, <&macaddr_mac_0>;
|
|
mac-address-increment = <3>;
|
|
qcom,ath10k-calibration-variant = "zte,mf289f";
|
|
};
|
|
|
|
/* This node is used only on AT1 version for 5Ghz on QCA9984 */
|
|
&pcie0 {
|
|
status = "okay";
|
|
perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
|
|
wake-gpio = <&tlmm 40 GPIO_ACTIVE_LOW>;
|
|
clkreq-gpio = <&tlmm 39 GPIO_ACTIVE_LOW>;
|
|
|
|
bridge@0,0 {
|
|
reg = <0x00000000 0 0 0 0>;
|
|
#address-cells = <3>;
|
|
#size-cells = <2>;
|
|
ranges;
|
|
|
|
wifi2: wifi@1,0 {
|
|
nvmem-cell-names = "mac-address";
|
|
nvmem-cells = <&macaddr_mac_0>;
|
|
mac-address-increment = <4>;
|
|
compatible = "qcom,ath10k";
|
|
reg = <0x00010000 0 0 0 0>;
|
|
qcom,ath10k-calibration-variant = "zte,mf289f";
|
|
};
|
|
};
|
|
};
|