Initial commit

target/linux/ath79/nand/base-files/etc/board.d/01_leds

@@ -0,0 +1,44 @@
+
+. /lib/functions/uci-defaults.sh
+
+board_config_update
+
+board=$(board_name)
+
+case "$board" in
+dongwon,dw02-412h-64m|\
+dongwon,dw02-412h-128m)
+	ucidef_set_led_switch "wan" "WAN" "green:wan" "switch0" "0x02"
+	;;
+glinet,gl-ar300m-nand|\
+glinet,gl-ar300m-nor)
+	ucidef_set_led_netdev "lan" "LAN" "green:lan" "eth0"
+	;;
+glinet,gl-xe300)
+	ucidef_set_led_netdev "wan" "WAN" "green:wan" "eth1"
+	ucidef_set_led_switch "lan" "LAN" "green:lan" "switch0" "0x10"
+	ucidef_set_led_netdev "3gnet" "LTE" "green:lte" "wwan0"
+	;;
+netgear,pgzng1)
+	ucidef_set_led_wlan "wlan" "WLAN" "green:wlan" "phy0tpt"
+	ucidef_set_led_switch "wan" "WAN" "green:wan-1" "switch0" "0x02" "0xf" "link tx rx"
+	ucidef_set_led_switch "wan-green" "wan link" "green:wan-0" "switch0" "0x02" "0xf" "link"
+	ucidef_set_led_switch "wan-amber" "wan act" "amber:wan" "switch0" "0x02" "0xf" "tx rx"
+	ucidef_set_led_netdev "lan-green" "lan link" "green:lan" "eth1" "link"
+	ucidef_set_led_netdev "lan-amber" "lan act" "amber:lan" "eth1" "tx rx"
+	;;
+netgear,r6100)
+	ucidef_set_led_netdev "wan-green" "WAN (green)" "green:wan" "eth1"
+	;;
+netgear,wndr3700-v4|\
+netgear,wndr4300|\
+netgear,wndr4300sw|\
+netgear,wndr4300-v2|\
+netgear,wndr4500-v3)
+	ucidef_set_led_switch "wan-amber" "WAN (amber)" "amber:wan" "switch0" "0x20"
+	;;
+esac
+
+board_config_flush
+
+exit 0

target/linux/ath79/nand/base-files/etc/board.d/02_network

@@ -0,0 +1,129 @@
+
+. /lib/functions/system.sh
+. /lib/functions/uci-defaults.sh
+
+ath79_setup_interfaces()
+{
+	local board="$1"
+
+	case "$board" in
+	aerohive,hiveap-121|\
+	meraki,mr18)
+		ucidef_set_interface_lan "eth0"
+		;;
+	domywifi,dw33d)
+		ucidef_add_switch "switch0" \
+			"0@eth0" "1:wan" "2:lan" "3:lan" "4:lan" "5:lan" "6@eth1"
+		;;
+	dongwon,dw02-412h-64m|\
+	dongwon,dw02-412h-128m)
+		ucidef_add_switch "switch0" \
+			"0@eth0" "2:lan:4" "3:lan:3" "4:lan:2" "5:lan:1" "1:wan"
+		;;
+	glinet,gl-ar750s-nor|\
+	glinet,gl-ar750s-nor-nand)
+		ucidef_add_switch "switch0" \
+			"0@eth0" "2:lan:2" "3:lan:1" "1:wan"
+		;;
+	glinet,gl-e750|\
+	zte,mf282)
+		ucidef_set_interface_lan "eth0"
+		ucidef_set_interface "wan" device "/dev/cdc-wdm0" protocol "qmi"
+		;;
+	glinet,gl-xe300)
+		ucidef_set_interface_wan "eth1"
+		ucidef_add_switch "switch0" \
+			"0@eth0" "4:lan"
+		;;
+	glinet,gl-x1200-nor|\
+	glinet,gl-x1200-nor-nand)
+		ucidef_add_switch "switch0" \
+			"0@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan"
+		;;
+	linksys,ea4500-v3)
+		ucidef_add_switch "switch0" \
+			"6@eth1" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan" "0@eth0"
+		;;
+	netgear,pgzng1)
+		ucidef_set_interfaces_lan_wan "eth1" "eth0"
+		;;
+	netgear,r6100)
+		ucidef_set_interface_wan "eth1"
+		ucidef_add_switch "switch0" \
+			"0@eth0" "1:lan:4" "2:lan:1" "3:lan:2" "4:lan:3"
+		;;
+	netgear,wndr3700-v4|\
+	netgear,wndr4300|\
+	netgear,wndr4300sw|\
+	netgear,wndr4300-v2)
+		ucidef_add_switch "switch0" \
+			"0@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan"
+		;;
+	netgear,wndr4500-v3)
+		ucidef_add_switch "switch0" \
+			"0@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan"
+		;;
+	netgear,wndr4300tn)
+		ucidef_add_switch "switch0" \
+			"0@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1"
+		;;
+	zte,mf281)
+		ucidef_add_switch "switch0" \
+			"0@eth0" "5:lan"
+		;;
+	zte,mf286|\
+	zte,mf286a|\
+	zte,mf286r)
+		ucidef_add_switch "switch0" \
+			"0@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "5:lan:1"
+		;;
+	zyxel,emg2926-q10a|\
+	zyxel,nbg6716)
+		ucidef_add_switch "switch0" \
+			"0@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan" "6@eth1"
+		;;
+	*)
+		ucidef_set_interfaces_lan_wan "eth0" "eth1"
+		;;
+	esac
+}
+
+ath79_setup_macs()
+{
+	local board="$1"
+
+	case "$board" in
+	dongwon,dw02-412h-64m|\
+	dongwon,dw02-412h-128m)
+		wan_mac=$(mtd_get_mac_binary art 0x0)
+		label_mac=$wan_mac
+		;;
+	glinet,gl-x1200-nor|\
+	glinet,gl-x1200-nor-nand)
+		wan_mac=$(mtd_get_mac_binary art 0x0)
+		lan_mac=$(macaddr_add "$wan_mac" 1)
+		;;
+	meraki,mr18)
+		lan_mac=$(mtd_get_mac_binary_ubi board-config 102)
+		;;
+	netgear,wndr3700-v4|\
+	netgear,wndr4300|\
+	netgear,wndr4300sw|\
+	netgear,wndr4300-v2|\
+	netgear,wndr4500-v3)
+		wan_mac=$(mtd_get_mac_binary caldata 0x6)
+		;;
+	esac
+
+	[ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac
+	[ -n "$wan_mac" ] && ucidef_set_interface_macaddr "wan" $wan_mac
+	[ -n "$label_mac" ] && ucidef_set_label_macaddr $label_mac
+}
+
+board_config_update
+board=$(board_name)
+ath79_setup_interfaces $board
+ath79_setup_macs $board
+board_config_flush
+
+exit 0

target/linux/ath79/nand/base-files/etc/board.d/03_gpio_switches

@@ -0,0 +1,20 @@
+#
+# Copyright (C) 2022 OpenWrt.org
+#
+
+. /lib/functions/uci-defaults.sh
+
+board_config_update
+
+board=$(board_name)
+
+case "$board" in
+zte,mf286a|\
+zte,mf286r)
+	ucidef_add_gpio_switch "power_btn_block" "Power button blocker" "532" "0"
+	;;
+esac
+
+board_config_flush
+
+exit 0

target/linux/ath79/nand/base-files/etc/board.d/05_compat-version

@@ -0,0 +1,15 @@
+. /lib/functions.sh
+. /lib/functions/uci-defaults.sh
+
+board_config_update
+
+case "$(board_name)" in
+	netgear,wndr4300-v2|\
+	netgear,wndr4500-v3)
+		ucidef_set_compat_version "1.1"
+		;;
+esac
+
+board_config_flush
+
+exit 0

target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom

@@ -0,0 +1,61 @@
+#!/bin/sh
+
+[ -e /lib/firmware/$FIRMWARE ] && exit 0
+
+. /lib/functions/caldata.sh
+
+board=$(board_name)
+
+case "$FIRMWARE" in
+"ath9k-eeprom-ahb-18100000.wmac.bin")
+	case $board in
+	meraki,mr18)
+		. /lib/upgrade/nand.sh
+
+		if [ -n "$(nand_find_volume ubi0 caldata)" ]; then
+			caldata_extract_ubi "caldata" 0x1000 0x440
+		else
+			caldata_extract "odm-caldata" 0x1000 0x440
+		fi
+		ath9k_patch_mac $(macaddr_add $(mtd_get_mac_binary_ubi board-config 102) 1)
+		;;
+	*)
+		caldata_die "board $board is not supported yet"
+		;;
+	esac
+	;;
+"ath9k-eeprom-pci-0000:00:00.0.bin")
+	case $board in
+	meraki,mr18)
+		. /lib/upgrade/nand.sh
+
+		if [ -n "$(nand_find_volume ubi0 caldata)" ]; then
+			caldata_extract_ubi "caldata" 0x5000 0x440
+		else
+			caldata_extract "odm-caldata" 0x5000 0x440
+		fi
+		ath9k_patch_mac $(macaddr_add $(mtd_get_mac_binary_ubi board-config 102) 2)
+		;;
+	*)
+		caldata_die "board $board is not supported yet"
+		;;
+	esac
+	;;
+"ath9k-eeprom-pci-0000:01:00.0.bin")
+	case $board in
+	meraki,mr18)
+		. /lib/upgrade/nand.sh
+
+		if [ -n "$(nand_find_volume ubi0 caldata)" ]; then
+			caldata_extract_ubi "caldata" 0x9000 0x440
+		else
+			caldata_extract "odm-caldata" 0x9000 0x440
+		fi
+		ath9k_patch_mac $(macaddr_add $(mtd_get_mac_binary_ubi board-config 102) 3)
+		;;
+	*)
+		caldata_die "board $board is not supported yet"
+		;;
+	esac
+	;;
+esac

target/linux/ath79/nand/base-files/etc/hotplug.d/ieee80211/10-fix-wifi-mac

@@ -0,0 +1,26 @@
+[ "$ACTION" = "add" ] || exit 0
+
+PHYNBR=${DEVPATH##*/phy}
+
+[ -n $PHYNBR ] || exit 0
+
+. /lib/functions.sh
+. /lib/functions/system.sh
+
+board=$(board_name)
+
+case $board in
+	glinet,gl-e750)
+		# Set mac address for 5g device
+		[ "$PHYNBR" -eq 0 ] && \
+			macaddr_add $(mtd_get_mac_binary art 0x0) 2 > /sys${DEVPATH}/macaddress
+		;;
+	zyxel,emg2926-q10a|\
+	zyxel,nbg6716)
+		ethaddr=$(mtd_get_mac_ascii u-boot-env ethaddr)
+		[ "$PHYNBR" -eq 0 ] && \
+			macaddr_add $ethaddr 1 > /sys${DEVPATH}/macaddress
+		[ "$PHYNBR" -eq 1 ] && \
+			echo -n $ethaddr > /sys${DEVPATH}/macaddress
+		;;
+esac

target/linux/ath79/nand/base-files/etc/init.d/boot-leds

@@ -0,0 +1,17 @@
+#!/bin/sh /etc/rc.common
+# SPDX-License-Identifier: GPL-2.0-only
+
+START=11
+
+# To support LEDs on boards that have drivers loaded after rootfs, let's
+# re-run diag.sh AFTER kmodloader has finished, but before boot is complete.
+# This is useful for userspace LED drivers, LEDs that rely on i2c, etc.
+
+boot() {
+    case $(board_name) in
+    netgear,pgzng1)
+        . /etc/diag.sh
+        set_led_state preinit_regular
+        ;;
+    esac
+}

target/linux/ath79/nand/base-files/etc/init.d/bootcount

@@ -0,0 +1,16 @@
+#!/bin/sh /etc/rc.common
+# SPDX-License-Identifier: GPL-2.0-only
+
+START=99
+
+boot() {
+	case $(board_name) in
+	glinet,gl-ar300m-nand)
+		fw_setenv bootcount 0
+		;;
+	linksys,ea4500-v3)
+		[ $(fw_printenv -n auto_recovery) = yes ] && \
+			fw_setenv auto_recovery no
+		;;
+	esac
+}

target/linux/ath79/nand/base-files/etc/uci-defaults/04_led_migration

@@ -0,0 +1,13 @@
+. /lib/functions.sh
+. /lib/functions/migrations.sh
+
+board=$(board_name)
+
+case "$board" in
+esac
+
+remove_devicename_leds
+
+migrations_apply system
+
+exit 0

target/linux/ath79/nand/base-files/lib/preinit/10_fix_eth_mac.sh

@@ -0,0 +1,15 @@
+. /lib/functions.sh
+. /lib/functions/system.sh
+
+preinit_set_mac_address() {
+	case $(board_name) in
+	zyxel,emg2926-q10a|\
+	zyxel,nbg6716)
+		ethaddr=$(mtd_get_mac_ascii u-boot-env ethaddr)
+		ip link set dev eth0 address $(macaddr_add $ethaddr 2)
+		ip link set dev eth1 address $(macaddr_add $ethaddr 3)
+		;;
+	esac
+}
+
+boot_hook_add preinit_main preinit_set_mac_address

target/linux/ath79/nand/base-files/lib/upgrade/glinet.sh

@@ -0,0 +1,90 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Copyright (C) 2019 Jeff Kletsky
+#
+
+glinet_using_boot_dev_switch() {
+	if [ "$(fw_printenv -n boot_dev 2>/dev/null)" = "on" ] ; then
+		>&2 echo "NOTE: boot_dev=on; use switch to control boot partition"
+		true
+	else
+		false
+	fi
+}
+
+glinet_set_next_boot_nand() {
+	mkdir -p /var/lock
+	! glinet_using_boot_dev_switch && \
+		fw_setenv bootcount 0 &&  \
+		>&2 echo "Next boot set for NAND"
+}
+
+glinet_set_next_boot_nor() {
+	mkdir -p /var/lock
+	! glinet_using_boot_dev_switch && \
+		fw_setenv bootcount 3 &&  \
+		>&2 echo "Next boot set for NOR"
+}
+
+glinet_nand_nor_do_upgrade() {
+	set_next_boot_nand() { glinet_set_next_boot_nand; }
+	set_next_boot_nor() { glinet_set_next_boot_nor; }
+	nand_nor_do_upgrade "$1"
+}
+
+nand_nor_do_upgrade() {
+	local upgrade_file="$1"
+
+	local pn
+	local found=""
+	local err
+
+	case "$(get_magic_long "$upgrade_file")" in
+
+	"27051956")	# U-Boot Image Magic
+
+		for pn in "nor_${PART_NAME}" "$PART_NAME" ; do		# firmware
+			if [ "$(find_mtd_index "$pn")" ] ; then
+				PART_NAME="$pn"
+				found="yes"
+				break
+			fi
+		done
+		if [ "$found" = "yes" ] ; then
+			>&2 echo "Running NOR upgrade"
+			default_do_upgrade "$upgrade_file"
+			# At this time, default_do_upgrade() exits on error
+			type set_next_boot_nor >/dev/null && set_next_boot_nor
+		else
+			>&2 echo "ERROR: UPGRADE FAILED: Unable to locate '$PART_NAME' or 'nor_${PART_NAME}'"
+			exit 1
+		fi
+		;;
+
+	*)	# otherwise a file that nand_do_upgrade can process
+
+		for pn in "nand_${CI_KERNPART}" "$CI_KERNPART" ; do	# kernel
+			if [ "$(find_mtd_index "$pn")" ] ; then
+				CI_KERNPART="$pn"
+				break
+			fi
+		done
+		for pn in "nand_${CI_UBIPART}" "$CI_UBIPART" ; do	# ubi
+			if [ "$(find_mtd_index "$pn")" ] ; then
+				CI_UBIPART="$pn"
+				break
+			fi
+		done
+		for pn in "nand_${CI_ROOTPART}" "$CI_ROOTPART" ; do	#rootfs
+			if [ "$(find_mtd_index "$pn")" ] ; then
+				CI_ROOTPART="$pn"
+				break
+			fi
+		done
+		>&2 echo "Running NAND upgrade"
+		# TODO: change order when NAND upgrade offers return
+		type set_next_boot_nand >/dev/null && set_next_boot_nand
+		nand_do_upgrade "$upgrade_file"
+		;;
+	esac
+}

target/linux/ath79/nand/base-files/lib/upgrade/platform.sh

@@ -0,0 +1,33 @@
+# Copyright (C) 2011 OpenWrt.org
+
+PART_NAME=firmware
+
+REQUIRE_IMAGE_METADATA=1
+platform_check_image() {
+	return 0
+}
+
+RAMFS_COPY_BIN='fw_printenv fw_setenv nandwrite'
+RAMFS_COPY_DATA='/etc/fw_env.config /var/lock/fw_printenv.lock'
+
+platform_do_upgrade() {
+	local board=$(board_name)
+
+	case "$board" in
+	glinet,gl-ar300m-nand|\
+	glinet,gl-ar300m-nor)
+		glinet_nand_nor_do_upgrade "$1"
+		;;
+	glinet,gl-ar750s-nor|\
+	glinet,gl-ar750s-nor-nand|\
+	glinet,gl-s200-nor|\
+	glinet,gl-s200-nor-nand|\
+	glinet,gl-x1200-nor|\
+	glinet,gl-x1200-nor-nand)
+		nand_nor_do_upgrade "$1"
+		;;
+	*)
+		nand_do_upgrade "$1"
+		;;
+	esac
+}

target/linux/ath79/nand/config-default

@@ -0,0 +1,31 @@
+CONFIG_BCH=y
+CONFIG_CRC16=y
+CONFIG_CRYPTO_DEFLATE=y
+CONFIG_CRYPTO_HASH_INFO=y
+CONFIG_CRYPTO_LZO=y
+CONFIG_CRYPTO_ZSTD=y
+CONFIG_LZO_COMPRESS=y
+CONFIG_LZO_DECOMPRESS=y
+CONFIG_MTD_NAND_AR934X=y
+CONFIG_MTD_NAND_CORE=y
+CONFIG_MTD_NAND_ECC=y
+CONFIG_MTD_NAND_ECC_SW_BCH=y
+# CONFIG_MTD_NAND_RB91X is not set
+CONFIG_MTD_RAW_NAND=y
+CONFIG_MTD_SPI_NAND=y
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_BEB_LIMIT=20
+CONFIG_MTD_UBI_BLOCK=y
+CONFIG_MTD_UBI_WL_THRESHOLD=4096
+# CONFIG_PCI_AR71XX is not set
+CONFIG_PHY_AR7200_USB=y
+CONFIG_POWER_RESET=y
+CONFIG_POWER_RESET_GPIO_RESTART=y
+CONFIG_SGL_ALLOC=y
+CONFIG_UBIFS_FS=y
+CONFIG_XXHASH=y
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZSTD_COMMON=y
+CONFIG_ZSTD_COMPRESS=y
+CONFIG_ZSTD_DECOMPRESS=y

target/linux/ath79/nand/target.mk

@@ -0,0 +1,10 @@
+BOARDNAME := Generic devices with NAND flash
+
+FEATURES += nand
+
+DEFAULT_PACKAGES += wpad-basic-mbedtls
+
+define Target/Description
+	Firmware for boards using Qualcomm Atheros, MIPS-based SoCs
+	in the ar72xx and subsequent series, with support for NAND flash
+endef