Initial commit

target/linux/realtek/dts-5.15/rtl8382_panasonic_m16eg-pn28160k.dts

@@ -0,0 +1,169 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "rtl838x.dtsi"
+#include "rtl83xx_panasonic_mxxeg-pn28xx0k.dtsi"
+
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "panasonic,m16eg-pn28160k", "realtek,rtl8382-soc";
+	model = "Panasonic Switch-M16eG PN28160K";
+
+	aliases {
+		led-boot = &led_status_eco_green;
+		led-failsafe = &led_status_eco_amber;
+		led-running = &led_status_eco_green;
+		led-upgrade = &led_status_eco_green;
+	};
+
+	/*
+	 * sfp0/1 are "combo" port with each TP port (23/24), and they are
+	 * connected to the RTL8218FB. Currently, there is no support for
+	 * the chip and only TP ports work by the RTL8218D support.
+	 */
+	sfp0: sfp-p23 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c0>;
+		tx-fault-gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+		tx-disable-gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
+		los-gpio = <&gpio1 3 GPIO_ACTIVE_HIGH>;
+	};
+
+	sfp1: sfp-p24 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c1>;
+		tx-fault-gpio = <&gpio1 4 GPIO_ACTIVE_HIGH>;
+		tx-disable-gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpio = <&gpio1 6 GPIO_ACTIVE_LOW>;
+		los-gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&leds {
+	led_status_eco_amber: led-5 {
+		gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+		color = <LED_COLOR_ID_AMBER>;
+		function = LED_FUNCTION_STATUS;
+		function-enumerator = <1>;
+	};
+
+	led_status_eco_green: led-6 {
+		gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
+		color = <LED_COLOR_ID_GREEN>;
+		function = LED_FUNCTION_STATUS;
+		function-enumerator = <2>;
+	};
+};
+
+&i2c_gpio_0 {
+	scl-gpios = <&gpio0 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio0 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+};
+
+&i2c_gpio_1 {
+	scl-gpios = <&gpio0 12 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio0 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+};
+
+&gpio2 {
+	interrupt-controller;
+	#interrupt-cells = <2>;
+	interrupt-parent = <&gpio0>;
+	interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+
+	/*
+	 * GPIO12 (IO1_4): RTL8218FB
+	 *
+	 * This GPIO pin should be specified as "reset-gpio" in mdio node, but
+	 * RTL8218FB phy won't be configured on RTL8218D support in the current
+	 * phy driver. So, ethernet ports on the phy will be broken after hard-
+	 * resetting.
+	 * (RTL8218FB phy will be detected as RTL8218D by the phy driver)
+	 * At the moment, configure this GPIO pin as gpio-hog to avoid breaking
+	 * by resetting.
+	 */
+	ext_switch_reset {
+		gpio-hog;
+		gpios = <12 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "ext-switch-reset";
+	};
+};
+
+&i2c_switch {
+	i2c0: i2c@0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0>;
+	};
+
+	i2c1: i2c@1 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <1>;
+	};
+};
+
+&ethernet0 {
+	mdio-bus {
+		compatible = "realtek,rtl838x-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		INTERNAL_PHY(8)
+		INTERNAL_PHY(9)
+		INTERNAL_PHY(10)
+		INTERNAL_PHY(11)
+		INTERNAL_PHY(12)
+		INTERNAL_PHY(13)
+		INTERNAL_PHY(14)
+		INTERNAL_PHY(15)
+
+		/* RTL8218FB */
+		EXTERNAL_PHY(16)
+		EXTERNAL_PHY(17)
+		EXTERNAL_PHY(18)
+		EXTERNAL_PHY(19)
+		EXTERNAL_PHY(20)
+		EXTERNAL_PHY(21)
+		EXTERNAL_PHY(22)
+		EXTERNAL_PHY(23)
+	};
+};
+
+&switch0 {
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		SWITCH_PORT(8, 1, internal)
+		SWITCH_PORT(9, 2, internal)
+		SWITCH_PORT(10, 3, internal)
+		SWITCH_PORT(11, 4, internal)
+		SWITCH_PORT(12, 5, internal)
+		SWITCH_PORT(13, 6, internal)
+		SWITCH_PORT(14, 7, internal)
+		SWITCH_PORT(15, 8, internal)
+
+		SWITCH_PORT(16, 9, qsgmii)
+		SWITCH_PORT(17, 10, qsgmii)
+		SWITCH_PORT(18, 11, qsgmii)
+		SWITCH_PORT(19, 12, qsgmii)
+		SWITCH_PORT(20, 13, qsgmii)
+		SWITCH_PORT(21, 14, qsgmii)
+		SWITCH_PORT(22, 15, qsgmii)
+		SWITCH_PORT(23, 16, qsgmii)
+
+		port@28 {
+			ethernet = <&ethernet0>;
+			reg = <28>;
+			phy-mode = "internal";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+	};
+};