Initial commit

target/linux/kirkwood/Makefile

@@ -0,0 +1,21 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Copyright (C) 2009-2015 OpenWrt.org
+
+include $(TOPDIR)/rules.mk
+
+ARCH:=arm
+BOARD:=kirkwood
+BOARDNAME:=Marvell Kirkwood
+FEATURES:=usb nand squashfs ramdisk
+CPU_TYPE:=xscale
+
+KERNEL_PATCHVER:=5.10
+
+include $(INCLUDE_DIR)/target.mk
+
+KERNELNAME:=zImage dtbs
+
+DEFAULT_PACKAGES += uboot-envtools kmod-usb2
+
+$(eval $(call BuildTarget))

target/linux/kirkwood/base-files/etc/board.d/01_leds

@@ -0,0 +1,23 @@
+#
+# Copyright (C) 2012-2015 OpenWrt.org
+#
+
+. /lib/functions/uci-defaults.sh
+
+board_config_update
+
+board=$(board_name)
+
+case "$board" in
+iom,ix2-200)
+	ucidef_set_led_timer "health" "health" "status:white:rebuild_led" "200" "800"
+	;;
+linksys,e4200-v2|\
+linksys,ea4500)
+	ucidef_set_led_default "pulse" "pulse" "viper:white:pulse" "1"
+	;;
+esac
+
+board_config_flush
+
+exit 0

target/linux/kirkwood/base-files/etc/board.d/02_network

@@ -0,0 +1,50 @@
+#
+# Copyright (C) 2012-2015 OpenWrt.org
+#
+
+. /lib/functions/uci-defaults.sh
+. /lib/functions/system.sh
+
+board_config_update
+
+board=$(board_name)
+
+case "$board" in
+checkpoint,l-50)
+	ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 lan5 lan6 lan7 lan8 dmz" "eth0"
+	;;
+cisco,on100)
+	ucidef_set_interface_lan "eth0 eth1"
+	;;
+cloudengines,pogoe02|\
+cloudengines,pogoplugv4|\
+globalscale,sheevaplug|\
+iom,iconnect-1.1|\
+iom,ix2-200|\
+raidsonic,ib-nas62x0|\
+seagate,blackarmor-nas220|\
+seagate,dockstar|\
+seagate,goflexhome|\
+seagate,goflexnet|\
+zyxel,nsa310s)
+	ucidef_set_interface_lan "eth0" "dhcp"
+	;;
+linksys,e4200-v2|\
+linksys,ea3500|\
+linksys,ea4500)
+	ucidef_set_interfaces_lan_wan "ethernet1 ethernet2 ethernet3 ethernet4" "internet"
+	ucidef_set_interface_macaddr "wan" $( mtd_get_mac_ascii u_env eth1addr )
+	;;
+zyxel,nsa310b|\
+zyxel,nsa325)
+	ucidef_set_interface_lan "eth0" "dhcp"
+	ucidef_set_interface_macaddr "lan" $( mtd_get_mac_ascii uboot_env ethaddr )
+	;;
+*)
+	ucidef_set_interface_lan "eth0"
+	;;
+esac
+
+board_config_flush
+
+exit 0

target/linux/kirkwood/base-files/etc/board.d/03_gpio_switches

@@ -0,0 +1,17 @@
+
+. /lib/functions/uci-defaults.sh
+
+board_config_update
+
+board=$(board_name)
+
+case "$board" in
+checkpoint,l-50)
+	ucidef_add_gpio_switch "mpcie-rst" "mPCIE Card reset" "502" "1"
+	ucidef_add_gpio_switch "exp-card-rst" "Express Card reset" "497" "1"
+	;;
+esac
+
+board_config_flush
+
+exit 0

target/linux/kirkwood/base-files/etc/board.d/05_compat-version

@@ -0,0 +1,20 @@
+#
+# Copyright (C) 2020 OpenWrt.org
+#
+
+. /lib/functions.sh
+. /lib/functions/uci-defaults.sh
+
+board_config_update
+
+case "$(board_name)" in
+	linksys,e4200-v2|\
+	linksys,ea3500|\
+	linksys,ea4500)
+		ucidef_set_compat_version "2.0"
+		;;
+esac
+
+board_config_flush
+
+exit 0

target/linux/kirkwood/base-files/etc/init.d/bootcount

@@ -0,0 +1,13 @@
+#!/bin/sh /etc/rc.common
+
+START=99
+
+boot() {
+	case $(board_name) in
+	linksys,e4200-v2|\
+	linksys,ea3500|\
+	linksys,ea4500)
+		mtd resetbc s_env || true
+		;;
+	esac
+}

target/linux/kirkwood/base-files/etc/init.d/hwmon_fancontrol

@@ -0,0 +1,48 @@
+#!/bin/sh /etc/rc.common
+
+START=98
+
+boot() {
+	# configuring (lm85/lm63) onboard temp/fan controller to run the fan on its own
+	# for more information, please read https://www.kernel.org/doc/Documentation/hwmon/sysfs-interface
+
+	case $(board_name) in
+	iom,ix2-200)
+		path_to_hwmon='/sys/class/hwmon/hwmon0'
+		echo 2 > "$path_to_hwmon/pwm1_enable" # fan is on pwm1
+		;;
+	seagate,blackarmor-nas220)
+		path_to_hwmon='/sys/devices/platform/ocp@f1000000/f1011000.i2c/i2c-0/0-002e/hwmon/hwmon0'
+		# adt7476 fan control chip. 3 temp sensors. Set to 1/4 speed at 35C and max speed at 48C.
+		echo 7 > "$path_to_hwmon/pwm1_auto_channels_temp"
+		echo 64 > "$path_to_hwmon/pwm1_auto_point1_pwm"
+		echo 255 > "$path_to_hwmon/pwm1_auto_point2_pwm"
+		echo 35000 > "$path_to_hwmon/temp1_auto_point1_temp"
+		echo 48000 > "$path_to_hwmon/temp1_auto_point2_temp"
+		echo 35000 > "$path_to_hwmon/temp2_auto_point1_temp"
+		echo 48000 > "$path_to_hwmon/temp2_auto_point2_temp"
+		echo 35000 > "$path_to_hwmon/temp3_auto_point1_temp"
+		echo 48000 > "$path_to_hwmon/temp3_auto_point2_temp"
+		echo 2 > "$path_to_hwmon/pwm1_enable"
+		;;
+	zyxel,nsa310b)
+		path_to_hwmon='/sys/devices/platform/ocp@f1000000/f1011000.i2c/i2c-0/0-002e/hwmon/hwmon0'
+		# use the max. value of (temp1) OR (temp2) OR (temp3) as an input
+		# for the PWM of the cooling fan
+		echo 123 > "$path_to_hwmon/pwm1_auto_channels"
+		# Temperature sensor #1 placed on mainboard
+		echo 30000 > "$path_to_hwmon/temp1_auto_temp_min"
+		echo 49600 > "$path_to_hwmon/temp1_auto_temp_max"
+		# Temperature sensor #2 placed on mainboard
+		# range: 0 to 127000 in steps of 1000 [millicelsius]
+		echo 30000 > "$path_to_hwmon/temp2_auto_temp_min"
+		# range: 0 to 127000 in steps of ???? [millicelsius]
+		echo 49600 > "$path_to_hwmon/temp2_auto_temp_max"
+		# Temperature sensor #3 placed close to a chipset
+		# range: 0 to 60000 in steps of 1000 [millicelsius]
+		echo 23000 > "$path_to_hwmon/temp3_auto_temp_min"
+		# pre-defined steps: 103000, 122000, 143300, 170000 in [millicelsius]
+		echo 103000 > "$path_to_hwmon/temp3_auto_temp_max"
+		;;
+	esac
+}

target/linux/kirkwood/base-files/lib/preinit/07_set_iface_mac

@@ -0,0 +1,25 @@
+. /lib/functions.sh
+. /lib/functions/system.sh
+
+preinit_set_mac_address() {
+	local mac
+
+	case $(board_name) in
+	checkpoint,l-50)
+		mac=$(mtd_get_mac_ascii bootldr-env lan1_mac_addr)
+
+		ip link set dev lan1 address $mac 2>/dev/null
+		ip link set dev lan2 address $(macaddr_add $mac 1) 2>/dev/null
+		ip link set dev lan3 address $(macaddr_add $mac 2) 2>/dev/null
+		ip link set dev lan4 address $(macaddr_add $mac 3) 2>/dev/null
+		ip link set dev lan5 address $(macaddr_add $mac 4) 2>/dev/null
+		ip link set dev lan6 address $(macaddr_add $mac 5) 2>/dev/null
+		ip link set dev lan7 address $(macaddr_add $mac 6) 2>/dev/null
+		ip link set dev lan8 address $(macaddr_add $mac 7) 2>/dev/null
+		ip link set dev dmz address $(macaddr_add $mac 8) 2>/dev/null
+		ip link set dev dsl address $(macaddr_add $mac 9) 2>/dev/null
+		;;
+	esac
+}
+
+boot_hook_add preinit_main preinit_set_mac_address

target/linux/kirkwood/base-files/lib/upgrade/linksys.sh

@@ -0,0 +1,93 @@
+#
+# Copyright (C) 2014 OpenWrt.org
+#
+
+linksys_get_target_firmware() {
+
+	local cur_boot_part mtd_ubi0
+
+	cur_boot_part=$(/usr/sbin/fw_printenv -n boot_part)
+	if [ -z "${cur_boot_part}" ] ; then
+		mtd_ubi0=$(cat /sys/devices/virtual/ubi/ubi0/mtd_num)
+		case $(egrep ^mtd${mtd_ubi0}: /proc/mtd | cut -d '"' -f 2) in
+		kernel|rootfs)
+			cur_boot_part=1
+			;;
+		alt_kernel|alt_rootfs)
+			cur_boot_part=2
+			;;
+		esac
+		>&2 printf "Current boot_part='%s' selected from ubi0/mtd_num='%s'" \
+			"${cur_boot_part}" "${mtd_ubi0}"
+	fi
+
+	case $cur_boot_part in
+	1)
+		fw_setenv -s - <<-EOF
+			boot_part 2
+			bootcmd "run altnandboot"
+		EOF
+		printf "kernel2"
+		return
+		;;
+	2)
+		fw_setenv -s - <<-EOF
+			boot_part 1
+			bootcmd "run nandboot"
+		EOF
+		printf "kernel1"
+		return
+		;;
+	*)
+		return
+		;;
+	esac
+}
+
+linksys_get_root_magic() {
+	(get_image "$@" | dd skip=786432 bs=4 count=1 | hexdump -v -n 4 -e '1/1 "%02x"') 2>/dev/null
+}
+
+platform_do_upgrade_linksys() {
+	local magic_long="$(get_magic_long "$1")"
+
+	mkdir -p /var/lock
+	local part_label="$(linksys_get_target_firmware)"
+	touch /var/lock/fw_printenv.lock
+
+	if [ ! -n "$part_label" ]
+	then
+		echo "cannot find target partition"
+		exit 1
+	fi
+
+	local target_mtd=$(find_mtd_part $part_label)
+
+	[ "$magic_long" = "73797375" ] && {
+		CI_KERNPART="$part_label"
+		if [ "$part_label" = "kernel1" ]
+		then
+			CI_UBIPART="rootfs1"
+		else
+			CI_UBIPART="rootfs2"
+		fi
+
+		nand_upgrade_tar "$1"
+	}
+	[ "$magic_long" = "27051956" ] && {
+		# check firmwares' rootfs types
+		local target_mtd=$(find_mtd_part $part_label)
+		local oldroot="$(linksys_get_root_magic $target_mtd)"
+		local newroot="$(linksys_get_root_magic "$1")"
+
+		if [ "$newroot" = "55424923" -a "$oldroot" = "55424923" ]
+		# we're upgrading from a firmware with UBI to one with UBI
+		then
+			# erase everything to be safe
+			mtd erase $part_label
+			get_image "$1" | mtd -n write - $part_label
+		else
+			get_image "$1" | mtd write - $part_label
+		fi
+	}
+}

target/linux/kirkwood/base-files/lib/upgrade/platform.sh

@@ -0,0 +1,23 @@
+RAMFS_COPY_BIN='fw_printenv fw_setenv'
+RAMFS_COPY_DATA='/etc/fw_env.config /var/lock/fw_printenv.lock'
+
+REQUIRE_IMAGE_METADATA=1
+
+platform_check_image() {
+	return 0
+}
+
+platform_do_upgrade() {
+	local board="$(board_name)"
+
+	case "$board" in
+	linksys,e4200-v2|\
+	linksys,ea3500|\
+	linksys,ea4500)
+		platform_do_upgrade_linksys "$1"
+		;;
+	*)
+		nand_do_upgrade "$1"
+		;;
+	esac
+}

target/linux/kirkwood/config-5.10

@@ -0,0 +1,289 @@
+CONFIG_ALIGNMENT_TRAP=y
+CONFIG_ARCH_32BIT_OFF_T=y
+CONFIG_ARCH_HIBERNATION_POSSIBLE=y
+CONFIG_ARCH_KEEP_MEMBLOCK=y
+CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y
+CONFIG_ARCH_MULTIPLATFORM=y
+CONFIG_ARCH_MULTI_CPU_AUTO=y
+# CONFIG_ARCH_MULTI_V4 is not set
+# CONFIG_ARCH_MULTI_V4T is not set
+CONFIG_ARCH_MULTI_V4_V5=y
+CONFIG_ARCH_MULTI_V5=y
+CONFIG_ARCH_MVEBU=y
+CONFIG_ARCH_NR_GPIO=0
+CONFIG_ARCH_OPTIONAL_KERNEL_RWX=y
+CONFIG_ARCH_SELECT_MEMORY_MODEL=y
+CONFIG_ARCH_SPARSEMEM_ENABLE=y
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_ARM=y
+# CONFIG_ARMADA_37XX_WATCHDOG is not set
+# CONFIG_ARMADA_THERMAL is not set
+CONFIG_ARM_APPENDED_DTB=y
+CONFIG_ARM_ATAG_DTB_COMPAT=y
+CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_FROM_BOOTLOADER=y
+CONFIG_ARM_HAS_SG_CHAIN=y
+# CONFIG_ARM_KIRKWOOD_CPUIDLE is not set
+CONFIG_ARM_L1_CACHE_SHIFT=5
+# CONFIG_ARM_MVEBU_V7_CPUIDLE is not set
+CONFIG_ARM_PATCH_PHYS_VIRT=y
+# CONFIG_ARM_THUMB is not set
+CONFIG_ARM_UNWIND=y
+CONFIG_ATA=y
+CONFIG_ATAGS=y
+CONFIG_ATA_LEDS=y
+CONFIG_AUTO_ZRELADDR=y
+CONFIG_BINFMT_FLAT_ARGVP_ENVP_ON_STACK=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_BLK_MQ_PCI=y
+CONFIG_BLK_SCSI_REQUEST=y
+CONFIG_CACHE_FEROCEON_L2=y
+# CONFIG_CACHE_FEROCEON_L2_WRITETHROUGH is not set
+CONFIG_CLKDEV_LOOKUP=y
+CONFIG_CLKSRC_MMIO=y
+CONFIG_CLONE_BACKWARDS=y
+CONFIG_COMMON_CLK=y
+CONFIG_COMPAT_32BIT_TIME=y
+CONFIG_CPU_32v5=y
+CONFIG_CPU_ABRT_EV5T=y
+CONFIG_CPU_CACHE_VIVT=y
+CONFIG_CPU_COPY_FEROCEON=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
+CONFIG_CPU_FEROCEON=y
+# CONFIG_CPU_FEROCEON_OLD_ID is not set
+CONFIG_CPU_IDLE=y
+CONFIG_CPU_IDLE_GOV_LADDER=y
+CONFIG_CPU_PABRT_LEGACY=y
+CONFIG_CPU_PM=y
+CONFIG_CPU_THERMAL=y
+CONFIG_CPU_THUMB_CAPABLE=y
+CONFIG_CPU_TLB_FEROCEON=y
+CONFIG_CPU_USE_DOMAINS=y
+CONFIG_CRC16=y
+# CONFIG_CRC32_SARWATE is not set
+CONFIG_CRC32_SLICEBY8=y
+CONFIG_CRYPTO_CRC32C=y
+CONFIG_CRYPTO_DEFLATE=y
+CONFIG_CRYPTO_DES=y
+CONFIG_CRYPTO_DEV_MARVELL=y
+CONFIG_CRYPTO_DEV_MARVELL_CESA=y
+CONFIG_CRYPTO_GF128MUL=y
+CONFIG_CRYPTO_HASH_INFO=y
+CONFIG_CRYPTO_HW=y
+CONFIG_CRYPTO_LIB_DES=y
+CONFIG_CRYPTO_LZO=y
+CONFIG_CRYPTO_NULL2=y
+CONFIG_CRYPTO_RNG2=y
+CONFIG_CRYPTO_ZSTD=y
+CONFIG_DEBUG_LL=y
+CONFIG_DEBUG_LL_INCLUDE="debug/8250.S"
+CONFIG_DEBUG_MVEBU_UART0_ALTERNATE=y
+# CONFIG_DEBUG_MVEBU_UART1_ALTERNATE is not set
+CONFIG_DEBUG_UART_8250=y
+CONFIG_DEBUG_UART_8250_SHIFT=2
+CONFIG_DEBUG_UART_PHYS=0xf1012000
+CONFIG_DEBUG_UART_VIRT=0xfed12000
+CONFIG_DEBUG_UNCOMPRESS=y
+# CONFIG_DLCI is not set
+CONFIG_DMA_OPS=y
+CONFIG_DMA_REMAP=y
+CONFIG_DNOTIFY=y
+CONFIG_DTC=y
+# CONFIG_EARLY_PRINTK is not set
+CONFIG_EDAC_ATOMIC_SCRUB=y
+CONFIG_EDAC_SUPPORT=y
+CONFIG_FIXED_PHY=y
+CONFIG_FIX_EARLYCON_MEM=y
+CONFIG_FORCE_PCI=y
+CONFIG_FW_LOADER_PAGED_BUF=y
+CONFIG_GENERIC_ALLOCATOR=y
+CONFIG_GENERIC_ATOMIC64=y
+CONFIG_GENERIC_BUG=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_CPU_AUTOPROBE=y
+CONFIG_GENERIC_EARLY_IOREMAP=y
+CONFIG_GENERIC_IDLE_POLL_SETUP=y
+CONFIG_GENERIC_IRQ_CHIP=y
+CONFIG_GENERIC_IRQ_MULTI_HANDLER=y
+CONFIG_GENERIC_IRQ_SHOW=y
+CONFIG_GENERIC_IRQ_SHOW_LEVEL=y
+CONFIG_GENERIC_PCI_IOMAP=y
+CONFIG_GENERIC_PHY=y
+CONFIG_GENERIC_PINCONF=y
+CONFIG_GENERIC_SCHED_CLOCK=y
+CONFIG_GENERIC_SMP_IDLE_THREAD=y
+CONFIG_GENERIC_STRNCPY_FROM_USER=y
+CONFIG_GENERIC_STRNLEN_USER=y
+CONFIG_GLOB=y
+CONFIG_GPIOLIB=y
+CONFIG_GPIOLIB_IRQCHIP=y
+CONFIG_GPIO_MVEBU=y
+CONFIG_GRO_CELLS=y
+CONFIG_HANDLE_DOMAIN_IRQ=y
+CONFIG_HARDIRQS_SW_RESEND=y
+CONFIG_HAS_DMA=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT_MAP=y
+CONFIG_HW_RANDOM=y
+CONFIG_HW_RANDOM_OMAP=y
+CONFIG_HZ_FIXED=0
+CONFIG_HZ_PERIODIC=y
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_MV64XXX=y
+# CONFIG_I2C_PXA is not set
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_IRQCHIP=y
+CONFIG_IRQ_DOMAIN=y
+CONFIG_IRQ_FORCED_THREADING=y
+CONFIG_IRQ_WORK=y
+CONFIG_KIRKWOOD_CLK=y
+CONFIG_KIRKWOOD_THERMAL=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_NETXBIG=y
+CONFIG_LEDS_NS2=y
+CONFIG_LIBFDT=y
+CONFIG_LLD_VERSION=0
+CONFIG_LOCK_DEBUGGING_SUPPORT=y
+CONFIG_LZO_COMPRESS=y
+CONFIG_LZO_DECOMPRESS=y
+CONFIG_MACH_KIRKWOOD=y
+CONFIG_MACH_MVEBU_ANY=y
+CONFIG_MANGLE_BOOTARGS=y
+CONFIG_MARVELL_PHY=y
+CONFIG_MDIO_BUS=y
+CONFIG_MDIO_DEVICE=y
+CONFIG_MDIO_DEVRES=y
+CONFIG_MEMFD_CREATE=y
+CONFIG_MIGRATION=y
+CONFIG_MODULES_USE_ELF_REL=y
+# CONFIG_MTD_CFI is not set
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_NAND_CORE=y
+CONFIG_MTD_NAND_ECC=y
+CONFIG_MTD_NAND_ECC_SW_HAMMING=y
+# CONFIG_MTD_NAND_MARVELL is not set
+CONFIG_MTD_NAND_ORION=y
+CONFIG_MTD_RAW_NAND=y
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_BEB_LIMIT=20
+CONFIG_MTD_UBI_BLOCK=y
+CONFIG_MTD_UBI_WL_THRESHOLD=4096
+CONFIG_MV643XX_ETH=y
+CONFIG_MVEBU_CLK_COMMON=y
+CONFIG_MVEBU_MBUS=y
+CONFIG_MVMDIO=y
+# CONFIG_MVNETA is not set
+# CONFIG_MVPP2 is not set
+CONFIG_NEED_DMA_MAP_STATE=y
+CONFIG_NEED_KUSER_HELPERS=y
+CONFIG_NEED_PER_CPU_KM=y
+CONFIG_NET_DEVLINK=y
+CONFIG_NET_DSA=y
+CONFIG_NET_DSA_MV88E6XXX=y
+CONFIG_NET_DSA_MV88E6XXX_GLOBAL2=y
+CONFIG_NET_DSA_TAG_DSA=y
+CONFIG_NET_DSA_TAG_EDSA=y
+CONFIG_NET_SWITCHDEV=y
+CONFIG_NLS=y
+CONFIG_NVMEM=y
+CONFIG_OF=y
+CONFIG_OF_ADDRESS=y
+CONFIG_OF_EARLY_FLATTREE=y
+CONFIG_OF_FLATTREE=y
+CONFIG_OF_GPIO=y
+CONFIG_OF_IRQ=y
+CONFIG_OF_KOBJ=y
+CONFIG_OF_MDIO=y
+CONFIG_OF_NET=y
+CONFIG_OLD_SIGACTION=y
+CONFIG_OLD_SIGSUSPEND3=y
+CONFIG_ORION_IRQCHIP=y
+CONFIG_ORION_TIMER=y
+CONFIG_ORION_WATCHDOG=y
+CONFIG_OUTER_CACHE=y
+CONFIG_PAGE_OFFSET=0xC0000000
+CONFIG_PCI=y
+CONFIG_PCI_BRIDGE_EMUL=y
+CONFIG_PCI_DOMAINS=y
+CONFIG_PCI_DOMAINS_GENERIC=y
+CONFIG_PCI_MVEBU=y
+CONFIG_PERF_USE_VMALLOC=y
+CONFIG_PGTABLE_LEVELS=2
+CONFIG_PHYLIB=y
+CONFIG_PHYLINK=y
+# CONFIG_PHY_MVEBU_A3700_UTMI is not set
+# CONFIG_PHY_MVEBU_A38X_COMPHY is not set
+CONFIG_PHY_MVEBU_SATA=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_KIRKWOOD=y
+CONFIG_PINCTRL_MVEBU=y
+# CONFIG_PINCTRL_SINGLE is not set
+CONFIG_PINCTRL_SX150X=y
+CONFIG_PLAT_ORION=y
+CONFIG_POWER_RESET=y
+CONFIG_POWER_RESET_GPIO=y
+# CONFIG_POWER_RESET_QNAP is not set
+CONFIG_POWER_SUPPLY=y
+CONFIG_RATIONAL=y
+CONFIG_REGMAP=y
+CONFIG_REGMAP_MMIO=y
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_MV=y
+CONFIG_RTC_I2C_AND_SPI=y
+CONFIG_RTC_MC146818_LIB=y
+CONFIG_SATA_HOST=y
+CONFIG_SATA_PMP=y
+CONFIG_SCSI=y
+CONFIG_SERIAL_8250_DEPRECATED_OPTIONS=y
+CONFIG_SERIAL_8250_FSL=y
+CONFIG_SERIAL_MCTRL_GPIO=y
+# CONFIG_SERIAL_MVEBU_UART is not set
+CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_SGL_ALLOC=y
+CONFIG_SG_POOL=y
+CONFIG_SOC_BUS=y
+CONFIG_SPARSE_IRQ=y
+CONFIG_SPI=y
+# CONFIG_SPI_ARMADA_3700 is not set
+CONFIG_SPI_MASTER=y
+CONFIG_SPI_ORION=y
+CONFIG_SPLIT_PTLOCK_CPUS=999999
+CONFIG_SRAM=y
+CONFIG_SRAM_EXEC=y
+CONFIG_SRCU=y
+CONFIG_SWPHY=y
+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+CONFIG_THERMAL=y
+CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y
+CONFIG_THERMAL_EMERGENCY_POWEROFF_DELAY_MS=0
+CONFIG_THERMAL_GOV_STEP_WISE=y
+CONFIG_THERMAL_OF=y
+CONFIG_TICK_CPU_ACCOUNTING=y
+CONFIG_TIMER_OF=y
+CONFIG_TIMER_PROBE=y
+CONFIG_TINY_SRCU=y
+CONFIG_UBIFS_FS=y
+CONFIG_UNCOMPRESS_INCLUDE="debug/uncompress.h"
+CONFIG_UNWINDER_ARM=y
+CONFIG_USB=y
+CONFIG_USB_COMMON=y
+CONFIG_USB_LED_TRIG=y
+CONFIG_USB_SUPPORT=y
+CONFIG_USE_OF=y
+# CONFIG_VFP is not set
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_WAN=y
+CONFIG_WATCHDOG_CORE=y
+CONFIG_XXHASH=y
+CONFIG_XZ_DEC_ARM=y
+CONFIG_XZ_DEC_BCJ=y
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZSTD_COMPRESS=y
+CONFIG_ZSTD_DECOMPRESS=y

target/linux/kirkwood/config-5.4

@@ -0,0 +1,281 @@
+CONFIG_ALIGNMENT_TRAP=y
+CONFIG_ARCH_32BIT_OFF_T=y
+CONFIG_ARCH_CLOCKSOURCE_DATA=y
+CONFIG_ARCH_HIBERNATION_POSSIBLE=y
+CONFIG_ARCH_KEEP_MEMBLOCK=y
+CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y
+CONFIG_ARCH_MULTIPLATFORM=y
+CONFIG_ARCH_MULTI_CPU_AUTO=y
+# CONFIG_ARCH_MULTI_V4 is not set
+# CONFIG_ARCH_MULTI_V4T is not set
+CONFIG_ARCH_MULTI_V4_V5=y
+CONFIG_ARCH_MULTI_V5=y
+CONFIG_ARCH_MVEBU=y
+CONFIG_ARCH_NR_GPIO=0
+CONFIG_ARCH_OPTIONAL_KERNEL_RWX=y
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_ARM=y
+# CONFIG_ARMADA_37XX_WATCHDOG is not set
+# CONFIG_ARMADA_THERMAL is not set
+CONFIG_ARM_APPENDED_DTB=y
+CONFIG_ARM_ATAG_DTB_COMPAT=y
+CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_FROM_BOOTLOADER=y
+CONFIG_ARM_HAS_SG_CHAIN=y
+# CONFIG_ARM_KIRKWOOD_CPUIDLE is not set
+CONFIG_ARM_L1_CACHE_SHIFT=5
+# CONFIG_ARM_MVEBU_V7_CPUIDLE is not set
+CONFIG_ARM_PATCH_PHYS_VIRT=y
+# CONFIG_ARM_THUMB is not set
+CONFIG_ARM_UNWIND=y
+CONFIG_ATA=y
+CONFIG_ATAGS=y
+CONFIG_ATA_LEDS=y
+CONFIG_AUTO_ZRELADDR=y
+CONFIG_BINFMT_FLAT_ARGVP_ENVP_ON_STACK=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_BLK_MQ_PCI=y
+CONFIG_BLK_SCSI_REQUEST=y
+CONFIG_CACHE_FEROCEON_L2=y
+# CONFIG_CACHE_FEROCEON_L2_WRITETHROUGH is not set
+CONFIG_CLKDEV_LOOKUP=y
+CONFIG_CLKSRC_MMIO=y
+CONFIG_CLONE_BACKWARDS=y
+CONFIG_COMMON_CLK=y
+CONFIG_COMPAT_32BIT_TIME=y
+CONFIG_CPU_32v5=y
+CONFIG_CPU_ABRT_EV5T=y
+CONFIG_CPU_CACHE_VIVT=y
+CONFIG_CPU_COPY_FEROCEON=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
+CONFIG_CPU_FEROCEON=y
+# CONFIG_CPU_FEROCEON_OLD_ID is not set
+CONFIG_CPU_IDLE=y
+CONFIG_CPU_IDLE_GOV_LADDER=y
+CONFIG_CPU_PABRT_LEGACY=y
+CONFIG_CPU_PM=y
+CONFIG_CPU_THUMB_CAPABLE=y
+CONFIG_CPU_TLB_FEROCEON=y
+CONFIG_CPU_USE_DOMAINS=y
+CONFIG_CRC16=y
+# CONFIG_CRC32_SARWATE is not set
+CONFIG_CRC32_SLICEBY8=y
+CONFIG_CRYPTO_ACOMP2=y
+CONFIG_CRYPTO_CRC32C=y
+CONFIG_CRYPTO_DEFLATE=y
+CONFIG_CRYPTO_DES=y
+CONFIG_CRYPTO_DEV_MARVELL_CESA=y
+CONFIG_CRYPTO_HASH=y
+CONFIG_CRYPTO_HASH2=y
+CONFIG_CRYPTO_HASH_INFO=y
+CONFIG_CRYPTO_HW=y
+CONFIG_CRYPTO_LIB_DES=y
+CONFIG_CRYPTO_LZO=y
+CONFIG_CRYPTO_RNG2=y
+CONFIG_DEBUG_LL=y
+CONFIG_DEBUG_LL_INCLUDE="debug/8250.S"
+CONFIG_DEBUG_MVEBU_UART0_ALTERNATE=y
+# CONFIG_DEBUG_MVEBU_UART1_ALTERNATE is not set
+CONFIG_DEBUG_UART_8250=y
+# CONFIG_DEBUG_UART_8250_FLOW_CONTROL is not set
+CONFIG_DEBUG_UART_8250_SHIFT=2
+# CONFIG_DEBUG_UART_8250_WORD is not set
+CONFIG_DEBUG_UART_PHYS=0xf1012000
+CONFIG_DEBUG_UART_VIRT=0xfed12000
+CONFIG_DEBUG_UNCOMPRESS=y
+# CONFIG_DLCI is not set
+CONFIG_DMA_REMAP=y
+CONFIG_DNOTIFY=y
+CONFIG_DTC=y
+# CONFIG_EARLY_PRINTK is not set
+CONFIG_EDAC_ATOMIC_SCRUB=y
+CONFIG_EDAC_SUPPORT=y
+CONFIG_FIXED_PHY=y
+CONFIG_FIX_EARLYCON_MEM=y
+CONFIG_FORCE_PCI=y
+CONFIG_FW_LOADER_PAGED_BUF=y
+CONFIG_GENERIC_ALLOCATOR=y
+CONFIG_GENERIC_ATOMIC64=y
+CONFIG_GENERIC_BUG=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_CPU_AUTOPROBE=y
+CONFIG_GENERIC_EARLY_IOREMAP=y
+CONFIG_GENERIC_IDLE_POLL_SETUP=y
+CONFIG_GENERIC_IRQ_CHIP=y
+CONFIG_GENERIC_IRQ_MULTI_HANDLER=y
+CONFIG_GENERIC_IRQ_SHOW=y
+CONFIG_GENERIC_IRQ_SHOW_LEVEL=y
+CONFIG_GENERIC_PCI_IOMAP=y
+CONFIG_GENERIC_PHY=y
+CONFIG_GENERIC_PINCONF=y
+CONFIG_GENERIC_SCHED_CLOCK=y
+CONFIG_GENERIC_SMP_IDLE_THREAD=y
+CONFIG_GENERIC_STRNCPY_FROM_USER=y
+CONFIG_GENERIC_STRNLEN_USER=y
+CONFIG_GLOB=y
+CONFIG_GPIOLIB=y
+CONFIG_GPIOLIB_IRQCHIP=y
+CONFIG_GPIO_MVEBU=y
+CONFIG_GRO_CELLS=y
+CONFIG_HANDLE_DOMAIN_IRQ=y
+CONFIG_HARDIRQS_SW_RESEND=y
+CONFIG_HAS_DMA=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT_MAP=y
+CONFIG_HW_RANDOM=y
+CONFIG_HW_RANDOM_OMAP=y
+CONFIG_HZ_FIXED=0
+CONFIG_HZ_PERIODIC=y
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_MV64XXX=y
+# CONFIG_I2C_PXA is not set
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_IRQCHIP=y
+CONFIG_IRQ_DOMAIN=y
+CONFIG_IRQ_FORCED_THREADING=y
+CONFIG_IRQ_WORK=y
+CONFIG_KIRKWOOD_CLK=y
+CONFIG_KIRKWOOD_THERMAL=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_NETXBIG=y
+CONFIG_LEDS_NS2=y
+CONFIG_LIBFDT=y
+CONFIG_LOCK_DEBUGGING_SUPPORT=y
+CONFIG_LZO_COMPRESS=y
+CONFIG_LZO_DECOMPRESS=y
+CONFIG_MACH_KIRKWOOD=y
+CONFIG_MACH_MVEBU_ANY=y
+CONFIG_MANGLE_BOOTARGS=y
+CONFIG_MARVELL_PHY=y
+CONFIG_MDIO_BUS=y
+CONFIG_MDIO_DEVICE=y
+CONFIG_MEMFD_CREATE=y
+CONFIG_MIGRATION=y
+CONFIG_MODULES_USE_ELF_REL=y
+# CONFIG_MTD_CFI is not set
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_NAND_CORE=y
+CONFIG_MTD_NAND_ECC_SW_HAMMING=y
+# CONFIG_MTD_NAND_MARVELL is not set
+CONFIG_MTD_NAND_ORION=y
+CONFIG_MTD_RAW_NAND=y
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_BEB_LIMIT=20
+CONFIG_MTD_UBI_BLOCK=y
+CONFIG_MTD_UBI_WL_THRESHOLD=4096
+CONFIG_MV643XX_ETH=y
+CONFIG_MVEBU_CLK_COMMON=y
+CONFIG_MVEBU_MBUS=y
+CONFIG_MVMDIO=y
+# CONFIG_MVNETA is not set
+# CONFIG_MVPP2 is not set
+CONFIG_NEED_DMA_MAP_STATE=y
+CONFIG_NEED_KUSER_HELPERS=y
+CONFIG_NEED_PER_CPU_KM=y
+CONFIG_NET_DEVLINK=y
+CONFIG_NET_DSA=y
+CONFIG_NET_DSA_MV88E6XXX=y
+CONFIG_NET_DSA_MV88E6XXX_GLOBAL2=y
+CONFIG_NET_DSA_TAG_DSA=y
+CONFIG_NET_DSA_TAG_EDSA=y
+CONFIG_NET_SWITCHDEV=y
+CONFIG_NLS=y
+CONFIG_NVMEM=y
+CONFIG_OF=y
+CONFIG_OF_ADDRESS=y
+CONFIG_OF_EARLY_FLATTREE=y
+CONFIG_OF_FLATTREE=y
+CONFIG_OF_GPIO=y
+CONFIG_OF_IRQ=y
+CONFIG_OF_KOBJ=y
+CONFIG_OF_MDIO=y
+CONFIG_OF_NET=y
+CONFIG_OLD_SIGACTION=y
+CONFIG_OLD_SIGSUSPEND3=y
+CONFIG_ORION_IRQCHIP=y
+CONFIG_ORION_TIMER=y
+CONFIG_ORION_WATCHDOG=y
+CONFIG_OUTER_CACHE=y
+CONFIG_PAGE_OFFSET=0xC0000000
+CONFIG_PCI=y
+CONFIG_PCI_BRIDGE_EMUL=y
+CONFIG_PCI_DOMAINS=y
+CONFIG_PCI_DOMAINS_GENERIC=y
+CONFIG_PCI_MVEBU=y
+CONFIG_PERF_USE_VMALLOC=y
+CONFIG_PGTABLE_LEVELS=2
+CONFIG_PHYLIB=y
+CONFIG_PHYLINK=y
+# CONFIG_PHY_MVEBU_A3700_UTMI is not set
+# CONFIG_PHY_MVEBU_A38X_COMPHY is not set
+CONFIG_PHY_MVEBU_SATA=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_KIRKWOOD=y
+CONFIG_PINCTRL_MVEBU=y
+# CONFIG_PINCTRL_SINGLE is not set
+CONFIG_PINCTRL_SX150X=y
+CONFIG_PLAT_ORION=y
+CONFIG_POWER_RESET=y
+CONFIG_POWER_RESET_GPIO=y
+# CONFIG_POWER_RESET_QNAP is not set
+CONFIG_POWER_SUPPLY=y
+CONFIG_RATIONAL=y
+CONFIG_REFCOUNT_FULL=y
+CONFIG_REGMAP=y
+CONFIG_REGMAP_MMIO=y
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_MV=y
+CONFIG_RTC_I2C_AND_SPI=y
+CONFIG_RTC_MC146818_LIB=y
+CONFIG_SATA_PMP=y
+CONFIG_SCSI=y
+CONFIG_SERIAL_8250_DEPRECATED_OPTIONS=y
+CONFIG_SERIAL_8250_FSL=y
+CONFIG_SERIAL_MCTRL_GPIO=y
+# CONFIG_SERIAL_MVEBU_UART is not set
+CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_SGL_ALLOC=y
+CONFIG_SG_POOL=y
+CONFIG_SOC_BUS=y
+CONFIG_SPARSE_IRQ=y
+CONFIG_SPI=y
+# CONFIG_SPI_ARMADA_3700 is not set
+CONFIG_SPI_MASTER=y
+CONFIG_SPI_ORION=y
+CONFIG_SPLIT_PTLOCK_CPUS=999999
+CONFIG_SRAM=y
+CONFIG_SRAM_EXEC=y
+CONFIG_SRCU=y
+CONFIG_SWPHY=y
+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+CONFIG_THERMAL=y
+CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y
+CONFIG_THERMAL_EMERGENCY_POWEROFF_DELAY_MS=0
+CONFIG_THERMAL_GOV_STEP_WISE=y
+CONFIG_THERMAL_OF=y
+CONFIG_TICK_CPU_ACCOUNTING=y
+CONFIG_TIMER_OF=y
+CONFIG_TIMER_PROBE=y
+CONFIG_TINY_SRCU=y
+CONFIG_UBIFS_FS=y
+CONFIG_UNCOMPRESS_INCLUDE="debug/uncompress.h"
+CONFIG_UNWINDER_ARM=y
+CONFIG_USB=y
+CONFIG_USB_COMMON=y
+CONFIG_USB_LED_TRIG=y
+CONFIG_USB_SUPPORT=y
+CONFIG_USE_OF=y
+# CONFIG_VFP is not set
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_WAN=y
+CONFIG_WATCHDOG_CORE=y
+CONFIG_XZ_DEC_ARM=y
+CONFIG_XZ_DEC_BCJ=y
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_ZLIB_INFLATE=y

target/linux/kirkwood/files/arch/arm/boot/dts/kirkwood-e4200-v2.dts

@@ -0,0 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "kirkwood-linksys-viper.dts"
+
+/ {
+	model = "Linksys E4200 v2 (Viper)";
+	compatible = "linksys,e4200-v2", "linksys,viper", "marvell,kirkwood-88f6282", "marvell,kirkwood";
+};

target/linux/kirkwood/files/arch/arm/boot/dts/kirkwood-ea3500.dts

@@ -0,0 +1,242 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * kirkwood-linksys-audi.dts - Device Tree file for Linksys EA3500
+ *
+ * (c) 2013 Jonas Gorski <jogo@openwrt.org>
+ * (c) 2013 Deutsche Telekom Innovation Laboratories
+ * (c) 2014 Luka Perkov <luka@openwrt.org>
+ * (c) 2014 Dan Walters <dan@walters.io>
+ *
+ */
+
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6282.dtsi"
+
+/ {
+	model = "Linksys EA3500 (Audi)";
+	compatible = "linksys,ea3500", "linksys,audi", "marvell,kirkwood-88f6282", "marvell,kirkwood";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x4000000>;
+	};
+
+	aliases {
+		led-boot = &led_power;
+		led-failsafe = &led_power;
+		led-running = &led_power;
+		led-upgrade = &led_power;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&pmx_btn_wps &pmx_btn_reset>;
+		pinctrl-names = "default";
+
+		wps {
+			label = "WPS Button";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+		};
+
+		reset {
+			label = "Reset Button";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		pinctrl-0 = <&pmx_led_green_power>;
+		pinctrl-names = "default";
+
+		led_power: power {
+			label = "audi:green:power";
+			gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+	};
+};
+
+&pinctrl {
+	pmx_led_green_power: pmx-led-green-power {
+		marvell,pins = "mpp7";
+		marvell,function = "gpo";
+	};
+
+	pmx_btn_wps: pmx-btn-wps {
+		marvell,pins = "mpp47";
+		marvell,function = "gpio";
+	};
+
+	pmx_btn_reset: pmx-btn-reset {
+		marvell,pins = "mpp48";
+		marvell,function = "gpio";
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	switch@10 {
+		compatible = "marvell,mv88e6085";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <16>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				label = "ethernet1";
+			};
+
+			port@1 {
+				reg = <1>;
+				label = "ethernet2";
+			};
+
+			port@2 {
+				reg = <2>;
+				label = "ethernet3";
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "ethernet4";
+			};
+
+			port@4 {
+				reg = <4>;
+				label = "internet";
+			};
+
+			port@5 {
+				reg = <5>;
+				label = "cpu";
+				ethernet = <&eth0port>;
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+		};
+	};
+};
+
+&nand {
+	status = "okay";
+
+	pinctrl-0 = <&pmx_nand>;
+	pinctrl-names = "default";
+
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			label = "u-boot";
+			reg = <0x0 0x80000>;
+			read-only;
+		};
+
+		partition@80000 {
+			label = "u_env";
+			reg = <0x80000 0x4000>;
+		};
+
+		partition@84000 {
+			label = "s_env";
+			reg = <0x84000 0x4000>;
+		};
+
+		partition@200000 {
+			label = "kernel1";
+			reg = <0x200000 0x1400000>;
+		};
+
+		partition@500000 {
+			label = "rootfs1";
+			reg = <0x500000 0x1100000>;
+		};
+
+		partition@1600000 {
+			label = "kernel2";
+			reg = <0x1600000 0x1400000>;
+		};
+
+		partition@1900000 {
+			label = "rootfs2";
+			reg = <0x1900000 0x1100000>;
+		};
+
+		partition@2a00000 {
+			label = "syscfg";
+			reg = <0x2a00000  0x1600000>;
+		};
+
+		partition@88000 {
+			label = "unused";
+			reg = <0x88000 0x178000>;
+		};
+	};
+};
+
+&pciec {
+	status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+};
+
+&mdio {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+/* eth0 is connected to a Marvell 88E6171 switch, without a PHY. So set
+ * fixed speed and duplex.
+ */
+&eth0 {
+	status = "okay";
+
+	ethernet0-port@0 {
+		speed = <1000>;
+		duplex = <1>;
+	};
+};
+
+/* eth1 is connected to the switch at port 6. However DSA only supports a
+ * single CPU port. This port is disabled to avoid confusion.
+ */
+&eth1 {
+	status = "disabled";
+};
+
+/* There is no battery on the board, so the RTC does not keep
+ * time when there is no power, making it useless.
+ */
+&rtc {
+	status = "disabled";
+};

target/linux/kirkwood/files/arch/arm/boot/dts/kirkwood-ea4500.dts

@@ -0,0 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "kirkwood-linksys-viper.dts"
+
+/ {
+	model = "Linksys EA4500 (Viper)";
+	compatible = "linksys,ea4500", "linksys,viper", "marvell,kirkwood-88f6282", "marvell,kirkwood";
+};

target/linux/kirkwood/files/arch/arm/boot/dts/kirkwood-goflexhome.dts

@@ -0,0 +1,135 @@
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+	model = "Seagate GoFlex Home";
+	compatible = "seagate,goflexhome", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+	aliases {
+		led-boot = &led_health;
+		led-failsafe = &led_fault;
+		led-running = &led_health;
+		led-upgrade = &led_fault;
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x8000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10";
+		stdout-path = &uart0;
+	};
+
+	ocp@f1000000 {
+		pinctrl: pin-controller@10000 {
+			pmx_usb_power_enable: pmx-usb-power-enable {
+				marvell,pins = "mpp29";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_white: pmx-led-white {
+				marvell,pins = "mpp40";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_green: pmx-led_green {
+				marvell,pins = "mpp46";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_orange: pmx-led-orange {
+				marvell,pins = "mpp47";
+				marvell,function = "gpio";
+			};
+		};
+
+		serial@12000 {
+			status = "okay";
+		};
+
+		sata@80000 {
+			status = "okay";
+			nr-ports = <2>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		led_health: health {
+			label = "status:green:health";
+			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+
+		led_fault: fault {
+			label = "status:orange:fault";
+			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+		};
+
+		misc {
+			label = "status:white:misc";
+			gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "disk-activity";
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pinctrl-0 = <&pmx_usb_power_enable>;
+		pinctrl-names = "default";
+
+		usb_power: regulator@1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "USB Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&nand {
+	status = "okay";
+
+	chip-delay = <40>;
+
+	partition@0 {
+		label = "u-boot";
+		reg = <0x0000000 0x0100000>;
+		read-only;
+	};
+
+	partition@100000 {
+		label = "ubi";
+		reg = <0x0100000 0xff00000>;
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};

target/linux/kirkwood/files/arch/arm/boot/dts/kirkwood-nsa310b.dts

@@ -0,0 +1,144 @@
+/dts-v1/;
+
+#include "kirkwood-nsa3x0-common.dtsi"
+
+/*
+ * There are at least two different NSA310 designs. This variant has
+ * a red/green USB Led (same as nsa310) and a lm85 temp/fan controller.
+ */
+
+/ {
+	model = "ZyXEL NSA310b";
+	compatible = "zyxel,nsa310b", "zyxel,nsa310", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+	aliases {
+		led-boot = &led_green_sys;
+		led-failsafe = &led_red_sys;
+		led-running = &led_green_sys;
+		led-upgrade = &led_red_sys;
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+		stdout-path = &uart0;
+	};
+
+	ocp@f1000000 {
+		pinctrl: pin-controller@10000 {
+			pinctrl-names = "default";
+
+			pmx_led_esata_green: pmx-led-esata-green {
+				marvell,pins = "mpp12";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_esata_red: pmx-led-esata-red {
+				marvell,pins = "mpp13";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_usb_green: pmx-led-usb-green {
+				marvell,pins = "mpp15";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_usb_red: pmx-led-usb-red {
+				marvell,pins = "mpp16";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_sys_green: pmx-led-sys-green {
+				marvell,pins = "mpp28";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_sys_red: pmx-led-sys-red {
+				marvell,pins = "mpp29";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_hdd_green: pmx-led-hdd-green {
+				marvell,pins = "mpp41";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_hdd_red: pmx-led-hdd-red {
+				marvell,pins = "mpp42";
+				marvell,function = "gpio";
+			};
+
+		};
+
+		i2c@11000 {
+			status = "okay";
+
+			lm85: lm85@2e {
+				compatible = "national,lm85";
+				reg = <0x2e>;
+			};
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		led_green_sys: green-sys {
+			label = "nsa310:green:sys";
+			gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+
+		led_red_sys: red-sys {
+			label = "nsa310:red:sys";
+			gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+		};
+
+		green-hdd {
+			label = "nsa310:green:hdd";
+			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "ata1";
+		};
+
+		red-hdd {
+			label = "nsa310:red:hdd";
+			gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+		};
+
+		green-esata {
+			label = "nsa310:green:esata";
+			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "ata2";
+		};
+
+		red-esata {
+			label = "nsa310:red:esata";
+			gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
+		};
+
+		green-usb {
+			label = "nsa310:green:usb";
+			gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "usb-host";
+		};
+
+		red-usb {
+			label = "nsa310:red:usb";
+			gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
+		};
+
+		green-copy {
+			label = "nsa310:green:copy";
+			gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+		};
+
+		red-copy {
+			label = "nsa310:red:copy";
+			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};

target/linux/kirkwood/files/arch/arm/boot/dts/kirkwood-nsa310s.dts

@@ -0,0 +1,271 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+	model = "ZyXEL NSA310S";
+	compatible = "zyxel,nsa310s", "marvell,kirkwood-88f6702", "marvell,kirkwood";
+
+	aliases {
+		led-boot = &led_green_sys;
+		led-failsafe = &led_red_sys;
+		led-running = &led_green_sys;
+		led-upgrade = &led_red_sys;
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 earlyprintk";
+		stdout-path = &uart0;
+	};
+
+	ocp@f1000000 {
+		pinctrl: pin-controller@10000 {
+			pinctrl-names = "default";
+
+			pmx_usb_power: pmx-usb-power {
+				marvell,pins = "mpp21";
+				marvell,function = "gpio";
+			};
+
+			pmx_pwr_off: pmx-pwr-off {
+				marvell,pins = "mpp27";
+				marvell,function = "gpio";
+			};
+
+			pmx_btn_reset: pmx-btn-reset {
+				marvell,pins = "mpp24";
+				marvell,function = "gpio";
+			};
+
+			pmx_btn_copy: pmx-btn-copy {
+				marvell,pins = "mpp25";
+				marvell,function = "gpio";
+			};
+
+			pmx_btn_power: pmx-btn-power {
+				marvell,pins = "mpp26";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_usb_green: pmx-led-usb-green {
+				marvell,pins = "mpp15";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_copy_green: pmx-led-copy-green {
+				marvell,pins = "mpp22";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_copy_red: pmx-led-copy-red {
+				marvell,pins = "mpp23";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_sys_green: pmx-led-sys-green {
+				marvell,pins = "mpp28";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_sys_red: pmx-led-sys-red {
+				marvell,pins = "mpp29";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_hdd1_green: pmx-led-hdd1-green {
+				marvell,pins = "mpp16";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_hdd1_red: pmx-led-hdd1-red {
+				marvell,pins = "mpp13";
+				marvell,function = "gpio";
+			};
+
+			pmx_pwr_sata1: pmx-pwr-sata1 {
+				marvell,pins = "mpp33";
+				marvell,function = "gpio";
+			};
+
+		};
+
+		i2c@11000 {
+			status = "okay";
+
+			rtc@68 {
+				compatible = "htk,ht1382";
+				reg = <0x68>;
+			};
+		};
+
+		serial@12000 {
+			status = "okay";
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = <&pmx_usb_power &pmx_pwr_sata1>;
+		pinctrl-names = "default";
+
+		usb0_power: regulator@1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "USB Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio0 21 GPIO_ACTIVE_HIGH>;
+		};
+
+		sata1_power: regulator@2 {
+			compatible = "regulator-fixed";
+			reg = <2>;
+			regulator-name = "SATA1 Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = <&pmx_btn_reset &pmx_btn_copy &pmx_btn_power>;
+		pinctrl-names = "default";
+
+		power {
+			label = "Power Button";
+			linux,code = <KEY_POWER>;
+			gpios = <&gpio0 26 GPIO_ACTIVE_HIGH>;
+		};
+
+		copy {
+			label = "Copy Button";
+			linux,code = <KEY_COPY>;
+			gpios = <&gpio0 25 GPIO_ACTIVE_LOW>;
+		};
+
+		reset {
+			label = "Reset Button";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_green_sys: green-sys {
+			label = "nsa310s:green:sys";
+			gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led_red_sys: red-sys {
+			label = "nsa310s:red:sys";
+			gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+		};
+
+		green-hdd1 {
+			label = "nsa310s:green:hdd1";
+			gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "ata1";
+		};
+
+		red-hdd1 {
+			label = "nsa310s:red:hdd1";
+			gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
+		};
+
+		green-usb {
+			label = "nsa310s:green:usb";
+			gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "usb-host";
+		};
+
+		green-copy {
+			label = "nsa310s:green:copy";
+			gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
+		};
+
+		red-copy {
+			label = "nsa310s:red:copy";
+			gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	gpio_poweroff {
+		compatible = "gpio-poweroff";
+		pinctrl-0 = <&pmx_pwr_off>;
+		pinctrl-names = "default";
+		gpios = <&gpio0 27 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+
+&eth0 {
+	status = "okay";
+
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@1 {
+		reg = <1>;
+		phy-mode = "rgmii-id";
+		marvell,reg-init = <0x1 0x16 0x0 0x3>,
+				   <0x1 0x10 0x0 0x1017>,
+				   <0x1 0x11 0x0 0x4408>,
+				   <0x1 0x16 0x0 0x0>;
+	};
+};
+
+&nand {
+	status = "okay";
+	chip-delay = <35>;
+
+	partition@0 {
+		label = "uboot";
+		reg = <0x0000000 0x00c0000>;
+		read-only;
+	};
+	partition@c0000 {
+		label = "uboot_env";
+		reg = <0x00c0000 0x0080000>;
+	};
+	partition@140000 {
+		label = "ubi";
+		reg = <0x0140000 0x7ec0000>;
+	};
+};
+
+&pciec {
+        status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+	nr-ports = <1>;
+};

target/linux/kirkwood/files/arch/arm/boot/dts/kirkwood-on100.dts

@@ -0,0 +1,165 @@
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6282.dtsi"
+
+/ {
+	model = "Cisco Systems ON100";
+	compatible = "cisco,on100", "marvell,kirkwood-88f6282", "marvell,kirkwood";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x20000000>;
+	};
+
+	aliases {
+		led-boot = &led_health_green;
+		led-failsafe = &led_health_red;
+		led-running = &led_health_green;
+		led-upgrade = &led_health_red;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 earlyprintk";
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&pmx_btn_reset>;
+		pinctrl-names = "default";
+
+		reset {
+			label = "Reset Button";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		pinctrl-0 = <&pmx_led_health_red &pmx_led_health_green>;
+		pinctrl-names = "default";
+
+		led_health_green: health-green {
+			label = "on100:green:health";
+			gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+
+		led_health_red: health-red {
+			label = "on100:red:health";
+			gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
+		};
+
+		health2-green {
+			label = "on100:green:health2";
+			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+		};
+
+		health2-red {
+			label = "on100:red:health2";
+			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&eth0 {
+	status = "okay";
+
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+		phy-connection-type = "rgmii-id";
+	};
+};
+
+&eth1 {
+	status = "okay";
+
+	ethernet1-port@0 {
+		phy-handle = <&ethphy1>;
+		phy-connection-type = "rgmii-id";
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		/* Marvell 88E1121R */
+		compatible = "ethernet-phy-id0141.0cb0",
+			     "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+
+	ethphy1: ethernet-phy@1 {
+		/* Marvell 88E1121R */
+		compatible = "ethernet-phy-id0141.0cb0",
+			     "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+&nand {
+	status = "okay";
+
+	partition@0 {
+		label = "u-boot";
+		reg = <0x00000000 0x000a0000>;
+		read-only;
+	};
+
+	partition@a0000 {
+		label = "u-boot environment";
+		reg = <0x000a0000 0x00020000>;
+		read-only;
+	};
+
+	partition@c0000 {
+		label = "kernel";
+		reg = <0x000c0000 0x00540000>;
+	};
+
+	partition@600000 {
+		label = "ubi";
+		reg = <0x00600000 0x1fa00000>;
+	};
+};
+
+&pinctrl {
+	pmx_led_health_red: pmx-led-health-red {
+		marvell,pins = "mpp45";
+		marvell,function = "gpio";
+	};
+
+	pmx_led_health_green: pmx-led-health-green {
+		marvell,pins = "mpp44";
+		marvell,function = "gpio";
+	};
+
+	pmx_led_health2_red: pmx-led-health2-red {
+		marvell,pins = "mpp47";
+		marvell,function = "gpio";
+	};
+
+	pmx_led_health2_green: pmx-led-health2-green {
+		marvell,pins = "mpp46";
+		marvell,function = "gpio";
+	};
+
+	pmx_btn_reset: pmx-btn-reset {
+		marvell,pins = "mpp31";
+		marvell,function = "gpio";
+	};
+};
+
+&sdio {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};

target/linux/kirkwood/image/Makefile

@@ -0,0 +1,215 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Copyright (C) 2009-2013 OpenWrt.org
+
+include $(TOPDIR)/rules.mk
+include $(INCLUDE_DIR)/image.mk
+
+KERNEL_LOADADDR:=0x8000
+
+define Device/kernel-size-migration
+  DEVICE_COMPAT_VERSION := 2.0
+  DEVICE_COMPAT_MESSAGE := Partition design has changed compared to \
+	older versions (up to 21.02) due to kernel size restrictions. \
+	Upgrade via sysupgrade mechanism is not possible, so new \
+	installation via factory style image is required.
+endef
+
+define Device/Default
+  PROFILES := Default
+  DEVICE_DTS = kirkwood-$(lastword $(subst _, ,$(1)))
+  KERNEL_DEPENDS = $$(wildcard $(DTS_DIR)/$$(DEVICE_DTS).dts)
+  KERNEL := kernel-bin | append-dtb | uImage none
+  KERNEL_NAME := zImage
+  KERNEL_SUFFIX  := -uImage
+  KERNEL_IN_UBI := 1
+
+  PAGESIZE := 2048
+  SUBPAGESIZE := 512
+  BLOCKSIZE := 128k
+  IMAGES := sysupgrade.bin factory.bin
+  IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+  IMAGE/factory.bin := append-ubi
+endef
+
+define Device/checkpoint_l-50
+  DEVICE_VENDOR := Check Point
+  DEVICE_MODEL := L-50
+  DEVICE_PACKAGES := kmod-ath9k kmod-gpio-button-hotplug kmod-mvsdio \
+	kmod-rtc-s35390a kmod-usb-ledtrig-usbport wpad-basic-wolfssl
+  IMAGES := sysupgrade.bin
+endef
+TARGET_DEVICES += checkpoint_l-50
+
+define Device/cisco_on100
+  DEVICE_VENDOR := Cisco Systems
+  DEVICE_MODEL := ON100
+  KERNEL_SIZE := 5376k
+  KERNEL_IN_UBI :=
+  UBINIZE_OPTS := -E 5
+  IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
+  DEVICE_PACKAGES := kmod-mvsdio
+  SUPPORTED_DEVICES += on100
+endef
+TARGET_DEVICES += cisco_on100
+
+define Device/cloudengines_pogoe02
+  DEVICE_VENDOR := Cloud Engines
+  DEVICE_MODEL := Pogoplug E02
+  DEVICE_DTS := kirkwood-pogo_e02
+  SUPPORTED_DEVICES += pogo_e02
+endef
+TARGET_DEVICES += cloudengines_pogoe02
+
+define Device/cloudengines_pogoplugv4
+  DEVICE_VENDOR := Cloud Engines
+  DEVICE_MODEL := Pogoplug V4
+  DEVICE_DTS := kirkwood-pogoplug-series-4
+  DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4 kmod-mvsdio kmod-usb3 \
+	kmod-gpio-button-hotplug
+endef
+TARGET_DEVICES += cloudengines_pogoplugv4
+
+define Device/globalscale_sheevaplug
+  DEVICE_VENDOR := Globalscale
+  DEVICE_MODEL := Sheevaplug
+  DEVICE_PACKAGES := kmod-mvsdio
+endef
+TARGET_DEVICES += globalscale_sheevaplug
+
+define Device/iom_iconnect-1.1
+  DEVICE_VENDOR := Iomega
+  DEVICE_MODEL := Iconnect
+  DEVICE_DTS := kirkwood-iconnect
+  SUPPORTED_DEVICES += iconnect
+endef
+TARGET_DEVICES += iom_iconnect-1.1
+
+define Device/iom_ix2-200
+  DEVICE_VENDOR := Iomega
+  DEVICE_MODEL := StorCenter ix2-200
+  DEVICE_DTS := kirkwood-iomega_ix2_200
+  DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4 \
+	kmod-gpio-button-hotplug kmod-hwmon-lm63
+  PAGESIZE := 512
+  SUBPAGESIZE := 256
+  BLOCKSIZE := 16k
+  KERNEL_SIZE := 3072k
+  KERNEL_IN_UBI :=
+  UBINIZE_OPTS := -E 5
+  IMAGE_SIZE := 31744k
+  IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | \
+	check-size
+endef
+TARGET_DEVICES += iom_ix2-200
+
+define Device/linksys
+  DEVICE_VENDOR := Linksys
+  DEVICE_PACKAGES := kmod-mwl8k wpad-basic-wolfssl kmod-gpio-button-hotplug
+  KERNEL_IN_UBI :=
+  UBINIZE_OPTS := -E 5
+  IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
+endef
+
+define Device/linksys_e4200-v2
+  $(Device/linksys)
+  $(Device/kernel-size-migration)
+  DEVICE_MODEL := E4200
+  DEVICE_VARIANT := v2
+  KERNEL_SIZE := 3072k
+  SUPPORTED_DEVICES += linksys,viper linksys-viper
+endef
+TARGET_DEVICES += linksys_e4200-v2
+
+define Device/linksys_ea3500
+  $(Device/linksys)
+  $(Device/kernel-size-migration)
+  DEVICE_MODEL := EA3500
+  PAGESIZE := 512
+  SUBPAGESIZE := 256
+  BLOCKSIZE := 16k
+  KERNEL_SIZE := 3072k
+  SUPPORTED_DEVICES += linksys,audi linksys-audi
+endef
+TARGET_DEVICES += linksys_ea3500
+
+define Device/linksys_ea4500
+  $(Device/linksys)
+  $(Device/kernel-size-migration)
+  DEVICE_MODEL := EA4500
+  KERNEL_SIZE := 3072k
+  SUPPORTED_DEVICES += linksys,viper linksys-viper
+endef
+TARGET_DEVICES += linksys_ea4500
+
+define Device/raidsonic_ib-nas62x0
+  DEVICE_VENDOR := RaidSonic
+  DEVICE_MODEL := ICY BOX IB-NAS62x0
+  DEVICE_DTS := kirkwood-ib62x0
+  DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4
+  SUPPORTED_DEVICES += ib62x0
+endef
+TARGET_DEVICES += raidsonic_ib-nas62x0
+
+define Device/seagate_blackarmor-nas220
+  DEVICE_VENDOR := Seagate
+  DEVICE_MODEL := Blackarmor NAS220
+  DEVICE_PACKAGES := kmod-hwmon-adt7475 kmod-fs-ext4 kmod-ata-marvell-sata \
+	mdadm kmod-gpio-button-hotplug
+  PAGESIZE := 512
+  SUBPAGESIZE := 256
+  BLOCKSIZE := 16k
+  UBINIZE_OPTS := -e 1
+endef
+TARGET_DEVICES += seagate_blackarmor-nas220
+
+define Device/seagate_dockstar
+  DEVICE_VENDOR := Seagate
+  DEVICE_MODEL := FreeAgent Dockstar
+  SUPPORTED_DEVICES += dockstar
+endef
+TARGET_DEVICES += seagate_dockstar
+
+define Device/seagate_goflexnet
+  DEVICE_VENDOR := Seagate
+  DEVICE_MODEL := GoFlexNet
+  DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4
+  SUPPORTED_DEVICES += goflexnet
+endef
+TARGET_DEVICES += seagate_goflexnet
+
+define Device/seagate_goflexhome
+  DEVICE_VENDOR := Seagate
+  DEVICE_MODEL := GoFlexHome
+  DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4
+  SUPPORTED_DEVICES += goflexhome
+endef
+TARGET_DEVICES += seagate_goflexhome
+
+define Device/zyxel_nsa310b
+  DEVICE_VENDOR := ZyXEL
+  DEVICE_MODEL := NSA310b
+  DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-r8169 kmod-fs-ext4 \
+	kmod-gpio-button-hotplug kmod-hwmon-lm85
+  SUPPORTED_DEVICES += nsa310b
+endef
+TARGET_DEVICES += zyxel_nsa310b
+
+define Device/zyxel_nsa310s
+  DEVICE_VENDOR := ZyXEL
+  DEVICE_MODEL := NSA310S
+  DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4 kmod-gpio-button-hotplug
+endef
+TARGET_DEVICES += zyxel_nsa310s
+
+define Device/zyxel_nsa325
+  DEVICE_VENDOR := ZyXEL
+  DEVICE_MODEL := NSA325
+  DEVICE_VARIANT := v1/v2
+  DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4 \
+	kmod-gpio-button-hotplug kmod-rtc-pcf8563 kmod-usb3
+  SUPPORTED_DEVICES += nsa325
+endef
+TARGET_DEVICES += zyxel_nsa325
+
+$(eval $(call BuildImage))

target/linux/kirkwood/patches-5.10/100-ib62x0.patch

@@ -0,0 +1,53 @@
+--- a/arch/arm/boot/dts/kirkwood-ib62x0.dts
++++ b/arch/arm/boot/dts/kirkwood-ib62x0.dts
+@@ -6,7 +6,14 @@
+ 
+ / {
+ 	model = "RaidSonic ICY BOX IB-NAS62x0 (Rev B)";
+-	compatible = "raidsonic,ib-nas6210-b", "raidsonic,ib-nas6220-b", "raidsonic,ib-nas6210", "raidsonic,ib-nas6220", "raidsonic,ib-nas62x0", "marvell,kirkwood-88f6281", "marvell,kirkwood";
++	compatible = "raidsonic,ib-nas62x0", "marvell,kirkwood-88f6281", "marvell,kirkwood";
++
++	aliases {
++		led-boot = &led_green_os;
++		led-failsafe = &led_red_os;
++		led-running = &led_green_os;
++		led-upgrade = &led_red_os;
++	};
+ 
+ 	memory {
+ 		device_type = "memory";
+@@ -81,12 +88,12 @@
+ 			     &pmx_led_usb_transfer>;
+ 		pinctrl-names = "default";
+ 
+-		green-os {
++		led_green_os: green-os {
+ 			label = "ib62x0:green:os";
+ 			gpios = <&gpio0 25 GPIO_ACTIVE_HIGH>;
+-			default-state = "keep";
++			default-state = "on";
+ 		};
+-		red-os {
++		led_red_os: red-os {
+ 			label = "ib62x0:red:os";
+ 			gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
+ 		};
+@@ -118,13 +125,13 @@
+ 	};
+ 
+ 	partition@100000 {
+-		label = "uImage";
+-		reg = <0x0100000 0x600000>;
++		label = "second stage u-boot";
++		reg = <0x100000 0x200000>;
+ 	};
+ 
+-	partition@700000 {
+-		label = "root";
+-		reg = <0x0700000 0xf900000>;
++	partition@200000 {
++		label = "ubi";
++		reg = <0x200000 0xfe00000>;
+ 	};
+ 
+ };

target/linux/kirkwood/patches-5.10/101-iconnect.patch

@@ -0,0 +1,80 @@
+--- a/arch/arm/boot/dts/kirkwood-iconnect.dts
++++ b/arch/arm/boot/dts/kirkwood-iconnect.dts
+@@ -8,6 +8,13 @@
+ 	model = "Iomega Iconnect";
+ 	compatible = "iom,iconnect-1.1", "iom,iconnect", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+ 
++	aliases {
++		led-boot = &led_power_blue;
++		led-failsafe = &led_power_red;
++		led-running = &led_power_blue;
++		led-upgrade = &led_power_red;
++	};
++
+ 	memory {
+ 		device_type = "memory";
+ 		reg = <0x00000000 0x10000000>;
+@@ -16,8 +23,6 @@
+ 	chosen {
+ 		bootargs = "console=ttyS0,115200n8 earlyprintk";
+ 		stdout-path = &uart0;
+-		linux,initrd-start = <0x4500040>;
+-		linux,initrd-end   = <0x4800000>;
+ 	};
+ 
+ 	ocp@f1000000 {
+@@ -89,12 +94,12 @@
+ 			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+ 			default-state = "on";
+ 		};
+-		power-blue {
++		led_power_blue: power-blue {
+ 			label = "power:blue";
+ 			gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+-			default-state = "keep";
++			default-state = "on";
+ 		};
+-		power-red {
++		led_power_red: power-red {
+ 			label = "power:red";
+ 			gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
+ 		};
+@@ -146,28 +151,23 @@
+ 	status = "okay";
+ 
+ 	partition@0 {
+-		label = "uboot";
+-		reg = <0x0000000 0xc0000>;
++		label = "u-boot";
++		reg = <0x0000000 0xe0000>;
+ 	};
+ 
+-	partition@a0000 {
+-		label = "env";
+-		reg = <0xa0000 0x20000>;
++	partition@e0000 {
++		label = "u-boot environment";
++		reg = <0xe0000 0x100000>;
+ 	};
+ 
+ 	partition@100000 {
+-		label = "zImage";
+-		reg = <0x100000 0x300000>;
+-	};
+-
+-	partition@540000 {
+-		label = "initrd";
+-		reg = <0x540000 0x300000>;
++		label = "second stage u-boot";
++		reg = <0x100000 0x200000>;
+ 	};
+ 
+-	partition@980000 {
+-		label = "boot";
+-		reg = <0x980000 0x1f400000>;
++	partition@200000 {
++		label = "ubi";
++		reg = <0x200000 0x1fe00000>;
+ 	};
+ };
+ 

target/linux/kirkwood/patches-5.10/102-dockstar.patch

@@ -0,0 +1,62 @@
+--- a/arch/arm/boot/dts/kirkwood-dockstar.dts
++++ b/arch/arm/boot/dts/kirkwood-dockstar.dts
+@@ -8,6 +8,13 @@
+ 	model = "Seagate FreeAgent Dockstar";
+ 	compatible = "seagate,dockstar", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+ 
++	aliases {
++		led-boot = &led_health;
++		led-failsafe = &led_fault;
++		led-running = &led_health;
++		led-upgrade = &led_fault;
++	};
++
+ 	memory {
+ 		device_type = "memory";
+ 		reg = <0x00000000 0x8000000>;
+@@ -42,12 +49,12 @@
+ 		pinctrl-0 = <&pmx_led_green &pmx_led_orange>;
+ 		pinctrl-names = "default";
+ 
+-		health {
++		led_health: health {
+ 			label = "status:green:health";
+ 			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+-			default-state = "keep";
++			default-state = "on";
+ 		};
+-		fault {
++		led_fault: fault {
+ 			label = "status:orange:fault";
+ 			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+ 		};
+@@ -78,18 +85,22 @@
+ 
+ 	partition@0 {
+ 		label = "u-boot";
+-		reg = <0x0000000 0x100000>;
+-		read-only;
++		reg = <0x0000000 0xe0000>;
++	};
++
++	partition@e0000 {
++		label = "u-boot environment";
++		reg = <0xe0000 0x100000>;
+ 	};
+ 
+ 	partition@100000 {
+-		label = "uImage";
+-		reg = <0x0100000 0x400000>;
++		label = "second stage u-boot";
++		reg = <0x100000 0x200000>;
+ 	};
+ 
+-	partition@500000 {
+-		label = "data";
+-		reg = <0x0500000 0xfb00000>;
++	partition@200000 {
++		label = "ubi";
++		reg = <0x200000 0xfe00000>;
+ 	};
+ };
+ 

target/linux/kirkwood/patches-5.10/103-iomega-ix2-200.patch

@@ -0,0 +1,67 @@
+--- a/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts
++++ b/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts
+@@ -8,6 +8,13 @@
+ 	model = "Iomega StorCenter ix2-200";
+ 	compatible = "iom,ix2-200", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+ 
++	aliases {
++		led-boot = &led_power;
++		led-failsafe = &led_health;
++		led-running = &led_power;
++		led-upgrade = &led_health;
++	};
++
+ 	memory {
+ 		device_type = "memory";
+ 		reg = <0x00000000 0x10000000>;
+@@ -127,16 +134,16 @@
+ 			      &pmx_led_rebuild &pmx_led_health >;
+ 		pinctrl-names = "default";
+ 
+-		power_led {
++		led_power: power_led {
+ 			label = "status:white:power_led";
+ 			gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
+-			default-state = "keep";
++			default-state = "on";
+ 		};
+ 		rebuild_led {
+ 			label = "status:white:rebuild_led";
+ 			gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
+ 		};
+-		health_led {
++		led_health: health_led {
+ 			label = "status:red:health_led";
+ 			gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+ 		};
+@@ -186,18 +193,18 @@
+ 	};
+ 
+ 	partition@a0000 {
+-		label = "env";
++		label = "u-boot environment";
+ 		reg = <0xa0000 0x20000>;
+ 		read-only;
+ 	};
+ 
+ 	partition@100000 {
+-		label = "uImage";
++		label = "kernel";
+ 		reg = <0x100000 0x300000>;
+ 	};
+ 
+ 	partition@400000 {
+-		label = "rootfs";
++		label = "ubi";
+ 		reg = <0x400000 0x1C00000>;
+ 	};
+ };
+@@ -211,7 +218,7 @@
+ };
+ 
+ &eth0 {
+-	status = "okay";
++	status = "disabled";
+ 	ethernet0-port@0 {
+ 		speed = <1000>;
+ 		duplex = <1>;

target/linux/kirkwood/patches-5.10/105-linksys-viper-dts.patch

@@ -0,0 +1,59 @@
+--- a/arch/arm/boot/dts/kirkwood-linksys-viper.dts
++++ b/arch/arm/boot/dts/kirkwood-linksys-viper.dts
+@@ -24,6 +24,10 @@
+ 	};
+ 
+ 	aliases {
++		led-boot = &led_white_health;
++		led-failsafe = &led_white_health;
++		led-running = &led_white_health;
++		led-upgrade = &led_white_health;
+ 		serial0 = &uart0;
+ 	};
+ 
+@@ -56,9 +60,10 @@
+ 		pinctrl-0 = < &pmx_led_white_health &pmx_led_white_pulse >;
+ 		pinctrl-names = "default";
+ 
+-		white-health {
++		led_white_health: white-health {
+ 			label = "viper:white:health";
+ 			gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
++			default-state = "on";
+ 		};
+ 
+ 		white-pulse {
+@@ -114,23 +119,23 @@
+ 		};
+ 
+ 		partition@200000 {
+-			label = "kernel";
+-			reg = <0x200000 0x2A0000>;
++			label = "kernel1";
++			reg = <0x200000 0x1A00000>;
+ 		};
+ 
+-		partition@4a0000 {
+-			label = "rootfs";
+-			reg = <0x4A0000 0x1760000>;
++		partition@500000 {
++			label = "rootfs1";
++			reg = <0x500000 0x1700000>;
+ 		};
+ 
+ 		partition@1c00000 {
+-			label = "alt_kernel";
+-			reg = <0x1C00000 0x2A0000>;
++			label = "kernel2";
++			reg = <0x1C00000 0x1A00000>;
+ 		};
+ 
+-		partition@1ea0000 {
+-			label = "alt_rootfs";
+-			reg = <0x1EA0000 0x1760000>;
++		partition@1f00000 {
++			label = "rootfs2";
++			reg = <0x1F00000 0x1700000>;
+ 		};
+ 
+ 		partition@3600000 {

target/linux/kirkwood/patches-5.10/106-goflexnet.patch

@@ -0,0 +1,53 @@
+--- a/arch/arm/boot/dts/kirkwood-goflexnet.dts
++++ b/arch/arm/boot/dts/kirkwood-goflexnet.dts
+@@ -8,6 +8,13 @@
+ 	model = "Seagate GoFlex Net";
+ 	compatible = "seagate,goflexnet", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+ 
++	aliases {
++		led-boot = &led_health;
++		led-failsafe = &led_fault;
++		led-running = &led_health;
++		led-upgrade = &led_fault;
++	};
++
+ 	memory {
+ 		device_type = "memory";
+ 		reg = <0x00000000 0x8000000>;
+@@ -85,12 +92,12 @@
+ 			    >;
+ 		pinctrl-names = "default";
+ 
+-		health {
++		led_health: health {
+ 			label = "status:green:health";
+ 			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+-			default-state = "keep";
++			default-state = "on";
+ 		};
+-		fault {
++		led_fault: fault {
+ 			label = "status:orange:fault";
+ 			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+ 		};
+@@ -159,18 +166,8 @@
+ 	};
+ 
+ 	partition@100000 {
+-		label = "uImage";
+-		reg = <0x0100000 0x400000>;
+-	};
+-
+-	partition@500000 {
+-		label = "pogoplug";
+-		reg = <0x0500000 0x2000000>;
+-	};
+-
+-	partition@2500000 {
+-		label = "root";
+-		reg = <0x02500000 0xd800000>;
++		label = "ubi";
++		reg = <0x0100000 0x0ff00000>;
+ 	};
+ };
+ 

target/linux/kirkwood/patches-5.10/107-01-zyxel-nsa3x0-common-nand-partitions.patch

@@ -0,0 +1,48 @@
+--- a/arch/arm/boot/dts/kirkwood-nsa3x0-common.dtsi
++++ b/arch/arm/boot/dts/kirkwood-nsa3x0-common.dtsi
+@@ -112,40 +112,16 @@
+ 
+ 	partition@0 {
+ 		label = "uboot";
+-		reg = <0x0000000 0x0100000>;
++		reg = <0x0000000 0x00c0000>;
+ 		read-only;
+ 	};
+ 	partition@100000 {
+ 		label = "uboot_env";
+-		reg = <0x0100000 0x0080000>;
++		reg = <0x00c0000 0x0080000>;
+ 	};
+-	partition@180000 {
+-		label = "key_store";
+-		reg = <0x0180000 0x0080000>;
+-	};
+-	partition@200000 {
+-		label = "info";
+-		reg = <0x0200000 0x0080000>;
+-	};
+-	partition@280000 {
+-		label = "etc";
+-		reg = <0x0280000 0x0a00000>;
+-	};
+-	partition@c80000 {
+-		label = "kernel_1";
+-		reg = <0x0c80000 0x0a00000>;
+-	};
+-	partition@1680000 {
+-		label = "rootfs1";
+-		reg = <0x1680000 0x2fc0000>;
+-	};
+-	partition@4640000 {
+-		label = "kernel_2";
+-		reg = <0x4640000 0x0a00000>;
+-	};
+-	partition@5040000 {
+-		label = "rootfs2";
+-		reg = <0x5040000 0x2fc0000>;
++	partition@140000 {
++		label = "ubi";
++		reg = <0x0140000 0x7ec0000>;
+ 	};
+ };
+ 

target/linux/kirkwood/patches-5.10/107-03-nsa325.patch

@@ -0,0 +1,54 @@
+--- a/arch/arm/boot/dts/kirkwood-nsa325.dts
++++ b/arch/arm/boot/dts/kirkwood-nsa325.dts
+@@ -15,6 +15,13 @@
+ 	model = "ZyXEL NSA325";
+ 	compatible = "zyxel,nsa325", "marvell,kirkwood-88f6282", "marvell,kirkwood";
+ 
++	aliases {
++		led-boot = &led_green_sys;
++		led-failsafe = &led_orange_sys;
++		led-running = &led_green_sys;
++		led-upgrade = &led_orange_sys;
++	};
++
+ 	memory {
+ 		device_type = "memory";
+ 		reg = <0x00000000 0x20000000>;
+@@ -162,17 +169,19 @@
+ 			     &pmx_led_hdd1_green &pmx_led_hdd1_red>;
+ 		pinctrl-names = "default";
+ 
+-		green-sys {
++		led_green_sys: green-sys {
+ 			label = "nsa325:green:sys";
+ 			gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
++			default-state = "on";
+ 		};
+-		orange-sys {
++		led_orange_sys: orange-sys {
+ 			label = "nsa325:orange:sys";
+ 			gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+ 		};
+ 		green-hdd1 {
+ 			label = "nsa325:green:hdd1";
+ 			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
++			linux,default-trigger = "ata1";
+ 		};
+ 		red-hdd1 {
+ 			label = "nsa325:red:hdd1";
+@@ -181,6 +190,7 @@
+ 		green-hdd2 {
+ 			label = "nsa325:green:hdd2";
+ 			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
++			linux,default-trigger = "ata2";
+ 		};
+ 		red-hdd2 {
+ 			label = "nsa325:red:hdd2";
+@@ -189,6 +199,7 @@
+ 		green-usb {
+ 			label = "nsa325:green:usb";
+ 			gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
++			linux,default-trigger = "usb-host";
+ 		};
+ 		green-copy {
+ 			label = "nsa325:green:copy";

target/linux/kirkwood/patches-5.10/109-pogoplug_v4.patch

@@ -0,0 +1,87 @@
+--- a/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts
++++ b/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts
+@@ -18,12 +18,20 @@
+ 	compatible = "cloudengines,pogoplugv4", "marvell,kirkwood-88f6192",
+ 		     "marvell,kirkwood";
+ 
++	aliases {
++		led-boot = &led_health;
++		led-failsafe = &led_fault;
++		led-running = &led_health;
++		led-upgrade = &led_fault;
++	};
++
+ 	memory {
+ 		device_type = "memory";
+ 		reg = <0x00000000 0x08000000>;
+ 	};
+ 
+ 	chosen {
++		bootargs = "console=ttyS0,115200";
+ 		stdout-path = "uart0:115200n8";
+ 	};
+ 
+@@ -37,8 +45,8 @@
+ 		eject {
+ 			debounce-interval = <50>;
+ 			wakeup-source;
+-			linux,code = <KEY_EJECTCD>;
+-			label = "Eject Button";
++			linux,code = <KEY_RESTART>;
++			label = "Reset";
+ 			gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
+ 		};
+ 	};
+@@ -48,12 +56,12 @@
+ 		pinctrl-0 = <&pmx_led_green &pmx_led_red>;
+ 		pinctrl-names = "default";
+ 
+-		health {
++		led_health: health {
+ 			label = "pogoplugv4:green:health";
+ 			gpios = <&gpio0 22 GPIO_ACTIVE_LOW>;
+ 			default-state = "on";
+ 		};
+-		fault {
++		led_fault: fault {
+ 			label = "pogoplugv4:red:fault";
+ 			gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
+ 		};
+@@ -137,29 +145,19 @@
+ 		#size-cells = <1>;
+ 
+ 		partition@0 {
+-			label = "u-boot";
+-			reg = <0x00000000 0x200000>;
++			label = "uboot";
++			reg = <0x00000000 0x1c0000>;
+ 			read-only;
+ 		};
+ 
+-		partition@200000 {
+-			label = "uImage";
+-			reg = <0x00200000 0x300000>;
+-		};
+-
+-		partition@500000 {
+-			label = "uImage2";
+-			reg = <0x00500000 0x300000>;
+-		};
+-
+-		partition@800000 {
+-			label = "failsafe";
+-			reg = <0x00800000 0x800000>;
++		partition@1c0000 {
++			label = "uboot_env";
++			reg = <0x001c0000 0x40000>;
+ 		};
+ 
+-		partition@1000000 {
+-			label = "root";
+-			reg = <0x01000000 0x7000000>;
++		partition@200000 {
++			label = "ubi";
++			reg = <0x00200000 0x7e00000>;
+ 		};
+ 	};
+ };

target/linux/kirkwood/patches-5.10/110-pogo_e02.patch

@@ -0,0 +1,68 @@
+--- a/arch/arm/boot/dts/kirkwood-pogo_e02.dts
++++ b/arch/arm/boot/dts/kirkwood-pogo_e02.dts
+@@ -20,6 +20,13 @@
+ 	compatible = "cloudengines,pogoe02", "marvell,kirkwood-88f6281",
+ 		     "marvell,kirkwood";
+ 
++	aliases {
++		led-boot = &led_health;
++		led-failsafe = &led_fault;
++		led-running = &led_health;
++		led-upgrade = &led_fault;
++	};
++
+ 	memory {
+ 		device_type = "memory";
+ 		reg = <0x00000000 0x10000000>;
+@@ -33,12 +40,12 @@
+ 	gpio-leds {
+ 		compatible = "gpio-leds";
+ 
+-		health {
++		led_health: health {
+ 			label = "pogo_e02:green:health";
+ 			gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
+-			default-state = "keep";
++			default-state = "on";
+ 		};
+-		fault {
++		led_fault: fault {
+ 			label = "pogo_e02:orange:fault";
+ 			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
+ 		};
+@@ -95,24 +102,24 @@
+ 	status = "okay";
+ 
+ 	partition@0 {
+-		label = "u-boot";
+-		reg = <0x0000000 0x100000>;
++		label = "uboot";
++		reg = <0x0 0xe0000>;
+ 		read-only;
+ 	};
+ 
+-	partition@100000 {
+-		label = "uImage";
+-		reg = <0x0100000 0x400000>;
++	partition@e0000 {
++		label = "uboot_env";
++		reg = <0xe0000 0x20000>;
+ 	};
+ 
+-	partition@500000 {
+-		label = "pogoplug";
+-		reg = <0x0500000 0x2000000>;
++	partition@100000 {
++		label = "second_stage_uboot";
++		reg = <0x100000 0x100000>;
+ 	};
+ 
+-	partition@2500000 {
+-		label = "root";
+-		reg = <0x02500000 0x5b00000>;
++	partition@200000 {
++		label = "ubi";
++		reg = <0x200000 0x7e00000>;
+ 	};
+ };
+ 

target/linux/kirkwood/patches-5.10/111-l-50.patch

@@ -0,0 +1,47 @@
+--- a/arch/arm/boot/dts/kirkwood-l-50.dts
++++ b/arch/arm/boot/dts/kirkwood-l-50.dts
+@@ -18,6 +18,13 @@
+ 		reg = <0x00000000 0x20000000>;
+ 	};
+ 
++	aliases {
++		led-boot = &led_status_green;
++		led-failsafe = &led_status_red;
++		led-running = &led_status_green;
++		led-upgrade = &led_status_red;
++	};
++
+ 	chosen {
+ 		bootargs = "console=ttyS0,115200n8";
+ 		stdout-path = &uart0;
+@@ -95,12 +102,12 @@
+ 	leds {
+ 		compatible = "gpio-leds";
+ 
+-		status_green {
++		led_status_green: status_green {
+ 			label = "l-50:green:status";
+ 			gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
+ 		};
+ 
+-		status_red {
++		led_status_red: status_red {
+ 			label = "l-50:red:status";
+ 			gpios = <&gpio3 2 GPIO_ACTIVE_LOW>;
+ 		};
+@@ -349,13 +356,8 @@
+ 	};
+ 
+ 	partition@100000 {
+-		label = "kernel-1";
+-		reg = <0x00100000 0x00800000>;
+-	};
+-
+-	partition@900000 {
+-		label = "rootfs-1";
+-		reg = <0x00900000 0x07100000>;
++		label = "ubi";
++		reg = <0x00100000 0x07900000>;
+ 	};
+ 
+ 	partition@7a00000 {

target/linux/kirkwood/patches-5.10/112-sheevaplug.patch

@@ -0,0 +1,47 @@
+--- a/arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi
++++ b/arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi
+@@ -78,13 +78,8 @@
+ 	};
+ 
+ 	partition@100000 {
+-		label = "uImage";
+-		reg = <0x0100000 0x400000>;
+-	};
+-
+-	partition@500000 {
+-		label = "root";
+-		reg = <0x0500000 0x1fb00000>;
++		label = "ubi";
++		reg = <0x0100000 0x1ff00000>;
+ 	};
+ };
+ 
+--- a/arch/arm/boot/dts/kirkwood-sheevaplug.dts
++++ b/arch/arm/boot/dts/kirkwood-sheevaplug.dts
+@@ -13,6 +13,13 @@
+ 	model = "Globalscale Technologies SheevaPlug";
+ 	compatible = "globalscale,sheevaplug", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+ 
++	aliases {
++		led-boot = &led_health;
++		led-failsafe = &led_health;
++		led-running = &led_health;
++		led-upgrade = &led_health;
++	};
++
+ 	ocp@f1000000 {
+ 		mvsdio@90000 {
+ 			pinctrl-0 = <&pmx_sdio>;
+@@ -28,10 +35,10 @@
+ 		pinctrl-0 = <&pmx_led_blue &pmx_led_red>;
+ 		pinctrl-names = "default";
+ 
+-		health {
++		led_health: health {
+ 			label = "sheevaplug:blue:health";
+ 			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
+-			default-state = "keep";
++			default-state = "on";
+ 		};
+ 
+ 		misc {

target/linux/kirkwood/patches-5.10/201-enable-sata-port-specific-led-triggers.patch

@@ -0,0 +1,10 @@
+--- a/arch/arm/mach-mvebu/Kconfig
++++ b/arch/arm/mach-mvebu/Kconfig
+@@ -116,6 +116,7 @@ config MACH_DOVE
+ config MACH_KIRKWOOD
+ 	bool "Marvell Kirkwood boards"
+ 	depends on ARCH_MULTI_V5
++	select ARCH_WANT_LIBATA_LEDS
+ 	select CPU_FEROCEON
+ 	select GPIOLIB
+ 	select KIRKWOOD_CLK

target/linux/kirkwood/patches-5.10/202-linksys-find-active-root.patch

@@ -0,0 +1,62 @@
+The WRT1900AC among other Linksys routers uses a dual-firmware layout.
+Dynamically rename the active partition to "ubi".
+
+Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
+---
+--- a/drivers/mtd/parsers/ofpart_core.c
++++ b/drivers/mtd/parsers/ofpart_core.c
+@@ -38,6 +38,8 @@ static bool node_has_compatible(struct d
+ 	return of_get_property(pp, "compatible", NULL);
+ }
+ 
++static int mangled_rootblock;
++
+ static int parse_fixed_partitions(struct mtd_info *master,
+ 				  const struct mtd_partition **pparts,
+ 				  struct mtd_part_parser_data *data)
+@@ -47,6 +49,7 @@ static int parse_fixed_partitions(struct
+ 	struct mtd_partition *parts;
+ 	struct device_node *mtd_node;
+ 	struct device_node *ofpart_node;
++	const char *owrtpart = "ubi";
+ 	const char *partname;
+ 	struct device_node *pp;
+ 	int nr_parts, i, ret = 0;
+@@ -133,9 +136,15 @@ static int parse_fixed_partitions(struct
+ 		parts[i].size = of_read_number(reg + a_cells, s_cells);
+ 		parts[i].of_node = pp;
+ 
+-		partname = of_get_property(pp, "label", &len);
+-		if (!partname)
+-			partname = of_get_property(pp, "name", &len);
++		if (mangled_rootblock && (i == mangled_rootblock)) {
++			partname = owrtpart;
++		} else {
++			partname = of_get_property(pp, "label", &len);
++
++			if (!partname)
++				partname = of_get_property(pp, "name", &len);
++		}
++
+ 		parts[i].name = partname;
+ 
+ 		if (of_get_property(pp, "read-only", &len))
+@@ -252,6 +261,18 @@ static int __init ofpart_parser_init(voi
+ 	return 0;
+ }
+ 
++static int __init active_root(char *str)
++{
++	get_option(&str, &mangled_rootblock);
++
++	if (!mangled_rootblock)
++		return 1;
++
++	return 1;
++}
++
++__setup("mangled_rootblock=", active_root);
++
+ static void __exit ofpart_parser_exit(void)
+ {
+ 	deregister_mtd_parser(&ofpart_parser);

target/linux/kirkwood/patches-5.10/203-blackarmor-nas220.patch

@@ -0,0 +1,99 @@
+--- a/arch/arm/boot/dts/kirkwood-blackarmor-nas220.dts
++++ b/arch/arm/boot/dts/kirkwood-blackarmor-nas220.dts
+@@ -17,6 +17,13 @@
+ 	compatible = "seagate,blackarmor-nas220","marvell,kirkwood-88f6192",
+ 		     "marvell,kirkwood";
+ 
++	aliases {
++		led-boot = &led_status_amber;
++		led-failsafe = &led_status_amber;
++		led-running = &led_status_blue;
++		led-upgrade = &led_status_amber;
++	};
++
+ 	memory { /* 128 MB */
+ 		device_type = "memory";
+ 		reg = <0x00000000 0x8000000>;
+@@ -36,14 +43,14 @@
+ 		compatible = "gpio-keys";
+ 
+ 		reset {
+-			label = "Reset";
+-			linux,code = <KEY_POWER>;
++			label = "Reset Button";
++			linux,code = <KEY_RESTART>;
+ 			gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+ 		};
+ 
+-		button {
+-			label = "Power";
+-			linux,code = <KEY_SLEEP>;
++		power {
++			label = "Power Button";
++			linux,code = <KEY_POWER>;
+ 			gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
+ 		};
+ 	};
+@@ -51,11 +58,27 @@
+ 	gpio-leds {
+ 		compatible = "gpio-leds";
+ 
+-		blue-power {
++		led_power_blue: power_blue {
+ 			label = "nas220:blue:power";
+ 			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+ 			linux,default-trigger = "default-on";
+ 		};
++
++		disk_blue {
++			label = "nas220:blue:disk";
++			gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
++			linux,default-trigger = "disk-activity";
++		};
++
++		led_status_blue: status_blue {
++			label = "nas220:blue:status";
++			gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>;
++		};
++
++		led_status_amber: status_amber {
++			label = "nas220:amber:status";
++			gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
++		};
+ 	};
+ 
+ 	regulators {
+@@ -153,6 +176,33 @@
+ 
+ &nand {
+ 	status = "okay";
++
++	partitions {
++		compatible = "fixed-partitions";
++
++		partition@0 {
++			label = "uboot";
++			reg = <0x0 0xa0000>;
++			read-only;
++		};
++
++		partition@a0000 {
++			label = "uboot-env";
++			reg = <0xa0000 0x10000>;
++			read-only;
++		};
++
++		partition@b0000 {
++			label = "reserved";
++			reg = <0xb0000 0x10000>;
++			read-only;
++		};
++
++		partition@c0000 {
++			label = "ubi";
++			reg = <0xc0000 0x1e80000>;
++		};
++	};
+ };
+ 
+ &mdio {

target/linux/kirkwood/patches-5.4/001-ARM-dts-kirkwood-Add-Check-Point-L-50-board.patch

@@ -0,0 +1,485 @@
+From efa968c18abab78c5e0c40a853caf286c3629a59 Mon Sep 17 00:00:00 2001
+From: Pawel Dembicki <paweldembicki@gmail.com>
+Date: Tue, 17 Mar 2020 21:28:01 +0100
+Subject: [PATCH v3] ARM: dts: kirkwood: Add Check Point L-50 board
+
+This patch adds dts for the Check Point L-50 from 600/1100 series
+routers.
+
+Specification:
+-CPU: Marvell Kirkwood 88F6821 1200MHz
+-RAM: 512MB
+-Flash: NAND 512MB
+-WiFi: mPCIe card based on Atheros AR9287 b/g/n
+-WAN: 1 Gigabit Port (Marvell 88E1116R PHY)
+-LAN: 9 Gigabit Ports (2x Marvell 88E6171(5+3))
+-USB: 2x USB2.0
+-Express card slot
+-SD card slot
+-Serial console: RJ-45 115200 8n1
+-Unsupported DSL
+
+Reviewed-by: Andrew Lunn <andrew@lunn.ch>
+Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
+---
+Changes in v3:
+- fix typo and code style issues pointed by OpenWrt guys
+Changes in v2:
+- none
+
+ arch/arm/boot/dts/Makefile          |   1 +
+ arch/arm/boot/dts/kirkwood-l-50.dts | 438 ++++++++++++++++++++++++++++
+ 2 files changed, 439 insertions(+)
+ create mode 100644 arch/arm/boot/dts/kirkwood-l-50.dts
+
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -270,6 +270,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
+ 	kirkwood-iomega_ix2_200.dtb \
+ 	kirkwood-is2.dtb \
+ 	kirkwood-km_kirkwood.dtb \
++	kirkwood-l-50.dtb \
+ 	kirkwood-laplug.dtb \
+ 	kirkwood-linkstation-lsqvl.dtb \
+ 	kirkwood-linkstation-lsvl.dtb \
+--- /dev/null
++++ b/arch/arm/boot/dts/kirkwood-l-50.dts
+@@ -0,0 +1,438 @@
++// SPDX-License-Identifier: GPL-2.0
++/*
++ * Check Point L-50 Board Description
++ * Copyright 2020 Pawel Dembicki <paweldembicki@gmail.com>
++ */
++
++/dts-v1/;
++
++#include "kirkwood.dtsi"
++#include "kirkwood-6281.dtsi"
++
++/ {
++	model = "Check Point L-50";
++	compatible = "checkpoint,l-50", "marvell,kirkwood-88f6281", "marvell,kirkwood";
++
++	memory {
++		device_type = "memory";
++		reg = <0x00000000 0x20000000>;
++	};
++
++	chosen {
++		bootargs = "console=ttyS0,115200n8";
++		stdout-path = &uart0;
++	};
++
++	ocp@f1000000 {
++		pinctrl: pin-controller@10000 {
++			pinctrl-0 = <&pmx_led38 &pmx_sysrst &pmx_button29>;
++			pinctrl-names = "default";
++
++			pmx_sysrst: pmx-sysrst {
++				marvell,pins = "mpp6";
++				marvell,function = "sysrst";
++			};
++
++			pmx_button29: pmx_button29 {
++				marvell,pins = "mpp29";
++				marvell,function = "gpio";
++			};
++
++			pmx_led38: pmx_led38 {
++				marvell,pins = "mpp38";
++				marvell,function = "gpio";
++			};
++
++			pmx_sdio_cd: pmx-sdio-cd {
++				marvell,pins = "mpp46";
++				marvell,function = "gpio";
++			};
++		};
++
++		serial@12000 {
++			status = "okay";
++		};
++
++		mvsdio@90000 {
++			status = "okay";
++			cd-gpios = <&gpio1 14 9>;
++		};
++
++		i2c@11000 {
++			status = "okay";
++			clock-frequency = <400000>;
++
++			gpio2: gpio-expander@20{
++				#gpio-cells = <2>;
++				#interrupt-cells = <2>;
++				compatible = "semtech,sx1505q";
++				reg = <0x20>;
++
++				gpio-controller;
++			};
++
++			/* Three GPIOs from 0x21 exp. are undescribed in dts:
++			 * 1: DSL module reset (active low)
++			 * 5: mPCIE reset (active low)
++			 * 6: Express card reset (active low)
++			 */
++			gpio3: gpio-expander@21{
++				#gpio-cells = <2>;
++				#interrupt-cells = <2>;
++				compatible = "semtech,sx1505q";
++				reg = <0x21>;
++
++				gpio-controller;
++			};
++
++			rtc@30 {
++				compatible = "s35390a";
++				reg = <0x30>;
++			};
++		};
++	};
++
++	leds {
++		compatible = "gpio-leds";
++
++		status_green {
++			label = "l-50:green:status";
++			gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
++		};
++
++		status_red {
++			label = "l-50:red:status";
++			gpios = <&gpio3 2 GPIO_ACTIVE_LOW>;
++		};
++
++		wifi {
++			label = "l-50:green:wifi";
++			gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
++			linux,default-trigger = "phy0tpt";
++		};
++
++		internet_green {
++			label = "l-50:green:internet";
++			gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
++		};
++
++		internet_red {
++			label = "l-50:red:internet";
++			gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
++		};
++
++		usb1_green {
++			label = "l-50:green:usb1";
++			gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
++			linux,default-trigger = "usbport";
++			trigger-sources = <&hub_port3>;
++		};
++
++		usb1_red {
++			label = "l-50:red:usb1";
++			gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
++		};
++
++		usb2_green {
++			label = "l-50:green:usb2";
++			gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
++			linux,default-trigger = "usbport";
++			trigger-sources = <&hub_port1>;
++		};
++
++		usb2_red {
++			label = "l-50:red:usb2";
++			gpios = <&gpio2 5 GPIO_ACTIVE_LOW>;
++		};
++	};
++
++	usb2_pwr {
++		compatible = "regulator-fixed";
++		regulator-name = "usb2_pwr";
++
++		regulator-min-microvolt = <5000000>;
++		regulator-max-microvolt = <5000000>;
++		gpio = <&gpio3 3 GPIO_ACTIVE_LOW>;
++		regulator-always-on;
++	};
++
++	usb1_pwr {
++		compatible = "regulator-fixed";
++		regulator-name = "usb1_pwr";
++
++		regulator-min-microvolt = <5000000>;
++		regulator-max-microvolt = <5000000>;
++		gpio = <&gpio3 4 GPIO_ACTIVE_LOW>;
++		regulator-always-on;
++	};
++
++	mpcie_pwr {
++		compatible = "regulator-fixed";
++		regulator-name = "mpcie_pwr";
++
++		regulator-min-microvolt = <3300000>;
++		regulator-max-microvolt = <3300000>;
++		gpio = <&gpio3 5 GPIO_ACTIVE_HIGH>;
++		enable-active-high;
++		regulator-always-on;
++	};
++
++	express_card_pwr {
++		compatible = "regulator-fixed";
++		regulator-name = "express_card_pwr";
++
++		regulator-min-microvolt = <3300000>;
++		regulator-max-microvolt = <3300000>;
++		gpio = <&gpio3 7 GPIO_ACTIVE_HIGH>;
++		enable-active-high;
++		regulator-always-on;
++	};
++
++	keys {
++		compatible = "gpio-keys";
++
++		factory_defaults {
++			label = "factory_defaults";
++			gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
++			linux,code = <KEY_RESTART>;
++		};
++	};
++};
++
++&mdio {
++	status = "okay";
++
++	ethphy8: ethernet-phy@8 {
++		reg = <0x08>;
++	};
++
++	switch0: switch@10 {
++		compatible = "marvell,mv88e6085";
++		#address-cells = <1>;
++		#size-cells = <0>;
++		reg = <0x10>;
++		dsa,member = <0 0>;
++
++		ports {
++			#address-cells = <1>;
++			#size-cells = <0>;
++
++			port@0 {
++				reg = <0>;
++				label = "lan5";
++			};
++
++			port@1 {
++			       reg = <1>;
++			       label = "lan1";
++			};
++
++			port@2 {
++			       reg = <2>;
++			       label = "lan6";
++			};
++
++			port@3 {
++			       reg = <3>;
++			       label = "lan2";
++			};
++
++			port@4 {
++				reg = <4>;
++				label = "lan7";
++			};
++
++			switch0port5: port@5 {
++				reg = <5>;
++				phy-mode = "rgmii-txid";
++				link = <&switch1port5>;
++				fixed-link {
++					speed = <1000>;
++					full-duplex;
++				};
++			};
++
++			port@6 {
++				reg = <6>;
++				label = "cpu";
++				phy-mode = "rgmii-id";
++				ethernet = <&eth1port>;
++				fixed-link {
++					speed = <1000>;
++					full-duplex;
++				};
++			};
++		};
++	};
++
++	switch@11 {
++		compatible = "marvell,mv88e6085";
++		#address-cells = <1>;
++		#size-cells = <0>;
++		reg = <0x11>;
++		dsa,member = <0 1>;
++
++		ports {
++			#address-cells = <1>;
++			#size-cells = <0>;
++
++			port@0 {
++				reg = <0>;
++				label = "lan3";
++			};
++
++			port@1 {
++			       reg = <1>;
++			       label = "lan8";
++			};
++
++			port@2 {
++			       reg = <2>;
++			       label = "lan4";
++			};
++
++			port@3 {
++			       reg = <3>;
++			       label = "dmz";
++			};
++
++			switch1port5: port@5 {
++				reg = <5>;
++				phy-mode = "rgmii-txid";
++				link = <&switch0port5>;
++				fixed-link {
++					speed = <1000>;
++					full-duplex;
++				};
++			};
++
++			port@6 {
++				reg = <6>;
++				label = "dsl";
++				fixed-link {
++					speed = <100>;
++					full-duplex;
++				};
++			};
++		};
++	};
++};
++
++&eth0 {
++	status = "okay";
++	ethernet0-port@0 {
++		phy-handle = <&ethphy8>;
++	};
++};
++
++&eth1 {
++	status = "okay";
++	ethernet1-port@0 {
++		speed = <1000>;
++		duplex = <1>;
++	};
++};
++
++&nand {
++	status = "okay";
++	pinctrl-0 = <&pmx_nand>;
++	pinctrl-names = "default";
++
++	partition@0 {
++		label = "u-boot";
++		reg = <0x00000000 0x000c0000>;
++	};
++
++	partition@a0000 {
++		label = "bootldr-env";
++		reg = <0x000c0000 0x00040000>;
++	};
++
++	partition@100000 {
++		label = "kernel-1";
++		reg = <0x00100000 0x00800000>;
++	};
++
++	partition@900000 {
++		label = "rootfs-1";
++		reg = <0x00900000 0x07100000>;
++	};
++
++	partition@7a00000 {
++		label = "kernel-2";
++		reg = <0x07a00000 0x00800000>;
++	};
++
++	partition@8200000 {
++		label = "rootfs-2";
++		reg = <0x08200000 0x07100000>;
++	};
++
++	partition@f300000 {
++		label = "default_sw";
++		reg = <0x0f300000 0x07900000>;
++	};
++
++	partition@16c00000 {
++		label = "logs";
++		reg = <0x16c00000 0x01800000>;
++	};
++
++	partition@18400000 {
++		label = "preset_cfg";
++		reg = <0x18400000 0x00100000>;
++	};
++
++	partition@18500000 {
++		label = "adsl";
++		reg = <0x18500000 0x00100000>;
++	};
++
++	partition@18600000 {
++		label = "storage";
++		reg = <0x18600000 0x07a00000>;
++	};
++};
++
++&rtc {
++	status = "disabled";
++};
++
++&pciec {
++	status = "okay";
++};
++
++&pcie0 {
++	status = "okay";
++};
++
++&sata_phy0 {
++	status = "disabled";
++};
++
++&sata_phy1 {
++	status = "disabled";
++};
++
++&usb0 {
++	#address-cells = <1>;
++	#size-cells = <0>;
++	status = "okay";
++
++	port@1 {
++		#address-cells = <1>;
++		#size-cells = <0>;
++		reg = <1>;
++		#trigger-source-cells = <0>;
++
++		hub_port1: port@1 {
++			reg = <1>;
++			#trigger-source-cells = <0>;
++		};
++
++		hub_port3: port@3 {
++			reg = <3>;
++			#trigger-source-cells = <0>;
++		};
++	};
++};

target/linux/kirkwood/patches-5.4/100-ib62x0.patch

@@ -0,0 +1,53 @@
+--- a/arch/arm/boot/dts/kirkwood-ib62x0.dts
++++ b/arch/arm/boot/dts/kirkwood-ib62x0.dts
+@@ -6,7 +6,14 @@
+ 
+ / {
+ 	model = "RaidSonic ICY BOX IB-NAS62x0 (Rev B)";
+-	compatible = "raidsonic,ib-nas6210-b", "raidsonic,ib-nas6220-b", "raidsonic,ib-nas6210", "raidsonic,ib-nas6220", "raidsonic,ib-nas62x0", "marvell,kirkwood-88f6281", "marvell,kirkwood";
++	compatible = "raidsonic,ib-nas62x0", "marvell,kirkwood-88f6281", "marvell,kirkwood";
++
++	aliases {
++		led-boot = &led_green_os;
++		led-failsafe = &led_red_os;
++		led-running = &led_green_os;
++		led-upgrade = &led_red_os;
++	};
+ 
+ 	memory {
+ 		device_type = "memory";
+@@ -81,12 +88,12 @@
+ 			     &pmx_led_usb_transfer>;
+ 		pinctrl-names = "default";
+ 
+-		green-os {
++		led_green_os: green-os {
+ 			label = "ib62x0:green:os";
+ 			gpios = <&gpio0 25 GPIO_ACTIVE_HIGH>;
+-			default-state = "keep";
++			default-state = "on";
+ 		};
+-		red-os {
++		led_red_os: red-os {
+ 			label = "ib62x0:red:os";
+ 			gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
+ 		};
+@@ -118,13 +125,13 @@
+ 	};
+ 
+ 	partition@100000 {
+-		label = "uImage";
+-		reg = <0x0100000 0x600000>;
++		label = "second stage u-boot";
++		reg = <0x100000 0x200000>;
+ 	};
+ 
+-	partition@700000 {
+-		label = "root";
+-		reg = <0x0700000 0xf900000>;
++	partition@200000 {
++		label = "ubi";
++		reg = <0x200000 0xfe00000>;
+ 	};
+ 
+ };

target/linux/kirkwood/patches-5.4/101-iconnect.patch

@@ -0,0 +1,80 @@
+--- a/arch/arm/boot/dts/kirkwood-iconnect.dts
++++ b/arch/arm/boot/dts/kirkwood-iconnect.dts
+@@ -8,6 +8,13 @@
+ 	model = "Iomega Iconnect";
+ 	compatible = "iom,iconnect-1.1", "iom,iconnect", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+ 
++	aliases {
++		led-boot = &led_power_blue;
++		led-failsafe = &led_power_red;
++		led-running = &led_power_blue;
++		led-upgrade = &led_power_red;
++	};
++
+ 	memory {
+ 		device_type = "memory";
+ 		reg = <0x00000000 0x10000000>;
+@@ -16,8 +23,6 @@
+ 	chosen {
+ 		bootargs = "console=ttyS0,115200n8 earlyprintk";
+ 		stdout-path = &uart0;
+-		linux,initrd-start = <0x4500040>;
+-		linux,initrd-end   = <0x4800000>;
+ 	};
+ 
+ 	ocp@f1000000 {
+@@ -89,12 +94,12 @@
+ 			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+ 			default-state = "on";
+ 		};
+-		power-blue {
++		led_power_blue: power-blue {
+ 			label = "power:blue";
+ 			gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+-			default-state = "keep";
++			default-state = "on";
+ 		};
+-		power-red {
++		led_power_red: power-red {
+ 			label = "power:red";
+ 			gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
+ 		};
+@@ -146,28 +151,23 @@
+ 	status = "okay";
+ 
+ 	partition@0 {
+-		label = "uboot";
+-		reg = <0x0000000 0xc0000>;
++		label = "u-boot";
++		reg = <0x0000000 0xe0000>;
+ 	};
+ 
+-	partition@a0000 {
+-		label = "env";
+-		reg = <0xa0000 0x20000>;
++	partition@e0000 {
++		label = "u-boot environment";
++		reg = <0xe0000 0x100000>;
+ 	};
+ 
+ 	partition@100000 {
+-		label = "zImage";
+-		reg = <0x100000 0x300000>;
+-	};
+-
+-	partition@540000 {
+-		label = "initrd";
+-		reg = <0x540000 0x300000>;
++		label = "second stage u-boot";
++		reg = <0x100000 0x200000>;
+ 	};
+ 
+-	partition@980000 {
+-		label = "boot";
+-		reg = <0x980000 0x1f400000>;
++	partition@200000 {
++		label = "ubi";
++		reg = <0x200000 0x1fe00000>;
+ 	};
+ };
+ 

target/linux/kirkwood/patches-5.4/102-dockstar.patch

@@ -0,0 +1,62 @@
+--- a/arch/arm/boot/dts/kirkwood-dockstar.dts
++++ b/arch/arm/boot/dts/kirkwood-dockstar.dts
+@@ -8,6 +8,13 @@
+ 	model = "Seagate FreeAgent Dockstar";
+ 	compatible = "seagate,dockstar", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+ 
++	aliases {
++		led-boot = &led_health;
++		led-failsafe = &led_fault;
++		led-running = &led_health;
++		led-upgrade = &led_fault;
++	};
++
+ 	memory {
+ 		device_type = "memory";
+ 		reg = <0x00000000 0x8000000>;
+@@ -42,12 +49,12 @@
+ 		pinctrl-0 = <&pmx_led_green &pmx_led_orange>;
+ 		pinctrl-names = "default";
+ 
+-		health {
++		led_health: health {
+ 			label = "status:green:health";
+ 			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+-			default-state = "keep";
++			default-state = "on";
+ 		};
+-		fault {
++		led_fault: fault {
+ 			label = "status:orange:fault";
+ 			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+ 		};
+@@ -78,18 +85,22 @@
+ 
+ 	partition@0 {
+ 		label = "u-boot";
+-		reg = <0x0000000 0x100000>;
+-		read-only;
++		reg = <0x0000000 0xe0000>;
++	};
++
++	partition@e0000 {
++		label = "u-boot environment";
++		reg = <0xe0000 0x100000>;
+ 	};
+ 
+ 	partition@100000 {
+-		label = "uImage";
+-		reg = <0x0100000 0x400000>;
++		label = "second stage u-boot";
++		reg = <0x100000 0x200000>;
+ 	};
+ 
+-	partition@500000 {
+-		label = "data";
+-		reg = <0x0500000 0xfb00000>;
++	partition@200000 {
++		label = "ubi";
++		reg = <0x200000 0xfe00000>;
+ 	};
+ };
+ 

target/linux/kirkwood/patches-5.4/103-iomega-ix2-200.patch

@@ -0,0 +1,67 @@
+--- a/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts
++++ b/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts
+@@ -8,6 +8,13 @@
+ 	model = "Iomega StorCenter ix2-200";
+ 	compatible = "iom,ix2-200", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+ 
++	aliases {
++		led-boot = &led_power;
++		led-failsafe = &led_health;
++		led-running = &led_power;
++		led-upgrade = &led_health;
++	};
++
+ 	memory {
+ 		device_type = "memory";
+ 		reg = <0x00000000 0x10000000>;
+@@ -127,16 +134,16 @@
+ 			      &pmx_led_rebuild &pmx_led_health >;
+ 		pinctrl-names = "default";
+ 
+-		power_led {
++		led_power: power_led {
+ 			label = "status:white:power_led";
+ 			gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
+-			default-state = "keep";
++			default-state = "on";
+ 		};
+ 		rebuild_led {
+ 			label = "status:white:rebuild_led";
+ 			gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
+ 		};
+-		health_led {
++		led_health: health_led {
+ 			label = "status:red:health_led";
+ 			gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+ 		};
+@@ -186,18 +193,18 @@
+ 	};
+ 
+ 	partition@a0000 {
+-		label = "env";
++		label = "u-boot environment";
+ 		reg = <0xa0000 0x20000>;
+ 		read-only;
+ 	};
+ 
+ 	partition@100000 {
+-		label = "uImage";
++		label = "kernel";
+ 		reg = <0x100000 0x300000>;
+ 	};
+ 
+ 	partition@400000 {
+-		label = "rootfs";
++		label = "ubi";
+ 		reg = <0x400000 0x1C00000>;
+ 	};
+ };
+@@ -211,7 +218,7 @@
+ };
+ 
+ &eth0 {
+-	status = "okay";
++	status = "disabled";
+ 	ethernet0-port@0 {
+ 		speed = <1000>;
+ 		duplex = <1>;

target/linux/kirkwood/patches-5.4/105-linksys-viper-dts.patch

@@ -0,0 +1,59 @@
+--- a/arch/arm/boot/dts/kirkwood-linksys-viper.dts
++++ b/arch/arm/boot/dts/kirkwood-linksys-viper.dts
+@@ -24,6 +24,10 @@
+ 	};
+ 
+ 	aliases {
++		led-boot = &led_white_health;
++		led-failsafe = &led_white_health;
++		led-running = &led_white_health;
++		led-upgrade = &led_white_health;
+ 		serial0 = &uart0;
+ 	};
+ 
+@@ -56,9 +60,10 @@
+ 		pinctrl-0 = < &pmx_led_white_health &pmx_led_white_pulse >;
+ 		pinctrl-names = "default";
+ 
+-		white-health {
++		led_white_health: white-health {
+ 			label = "viper:white:health";
+ 			gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
++			default-state = "on";
+ 		};
+ 
+ 		white-pulse {
+@@ -114,23 +119,23 @@
+ 		};
+ 
+ 		partition@200000 {
+-			label = "kernel";
+-			reg = <0x200000 0x2A0000>;
++			label = "kernel1";
++			reg = <0x200000 0x1A00000>;
+ 		};
+ 
+-		partition@4a0000 {
+-			label = "rootfs";
+-			reg = <0x4A0000 0x1760000>;
++		partition@500000 {
++			label = "rootfs1";
++			reg = <0x500000 0x1700000>;
+ 		};
+ 
+ 		partition@1c00000 {
+-			label = "alt_kernel";
+-			reg = <0x1C00000 0x2A0000>;
++			label = "kernel2";
++			reg = <0x1C00000 0x1A00000>;
+ 		};
+ 
+-		partition@1ea0000 {
+-			label = "alt_rootfs";
+-			reg = <0x1EA0000 0x1760000>;
++		partition@1f00000 {
++			label = "rootfs2";
++			reg = <0x1F00000 0x1700000>;
+ 		};
+ 
+ 		partition@3600000 {

target/linux/kirkwood/patches-5.4/106-goflexnet.patch

@@ -0,0 +1,53 @@
+--- a/arch/arm/boot/dts/kirkwood-goflexnet.dts
++++ b/arch/arm/boot/dts/kirkwood-goflexnet.dts
+@@ -8,6 +8,13 @@
+ 	model = "Seagate GoFlex Net";
+ 	compatible = "seagate,goflexnet", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+ 
++	aliases {
++		led-boot = &led_health;
++		led-failsafe = &led_fault;
++		led-running = &led_health;
++		led-upgrade = &led_fault;
++	};
++
+ 	memory {
+ 		device_type = "memory";
+ 		reg = <0x00000000 0x8000000>;
+@@ -85,12 +92,12 @@
+ 			    >;
+ 		pinctrl-names = "default";
+ 
+-		health {
++		led_health: health {
+ 			label = "status:green:health";
+ 			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+-			default-state = "keep";
++			default-state = "on";
+ 		};
+-		fault {
++		led_fault: fault {
+ 			label = "status:orange:fault";
+ 			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+ 		};
+@@ -159,18 +166,8 @@
+ 	};
+ 
+ 	partition@100000 {
+-		label = "uImage";
+-		reg = <0x0100000 0x400000>;
+-	};
+-
+-	partition@500000 {
+-		label = "pogoplug";
+-		reg = <0x0500000 0x2000000>;
+-	};
+-
+-	partition@2500000 {
+-		label = "root";
+-		reg = <0x02500000 0xd800000>;
++		label = "ubi";
++		reg = <0x0100000 0x0ff00000>;
+ 	};
+ };
+ 

target/linux/kirkwood/patches-5.4/107-01-zyxel-nsa3x0-common-nand-partitions.patch

@@ -0,0 +1,48 @@
+--- a/arch/arm/boot/dts/kirkwood-nsa3x0-common.dtsi
++++ b/arch/arm/boot/dts/kirkwood-nsa3x0-common.dtsi
+@@ -112,40 +112,16 @@
+ 
+ 	partition@0 {
+ 		label = "uboot";
+-		reg = <0x0000000 0x0100000>;
++		reg = <0x0000000 0x00c0000>;
+ 		read-only;
+ 	};
+ 	partition@100000 {
+ 		label = "uboot_env";
+-		reg = <0x0100000 0x0080000>;
++		reg = <0x00c0000 0x0080000>;
+ 	};
+-	partition@180000 {
+-		label = "key_store";
+-		reg = <0x0180000 0x0080000>;
+-	};
+-	partition@200000 {
+-		label = "info";
+-		reg = <0x0200000 0x0080000>;
+-	};
+-	partition@280000 {
+-		label = "etc";
+-		reg = <0x0280000 0x0a00000>;
+-	};
+-	partition@c80000 {
+-		label = "kernel_1";
+-		reg = <0x0c80000 0x0a00000>;
+-	};
+-	partition@1680000 {
+-		label = "rootfs1";
+-		reg = <0x1680000 0x2fc0000>;
+-	};
+-	partition@4640000 {
+-		label = "kernel_2";
+-		reg = <0x4640000 0x0a00000>;
+-	};
+-	partition@5040000 {
+-		label = "rootfs2";
+-		reg = <0x5040000 0x2fc0000>;
++	partition@140000 {
++		label = "ubi";
++		reg = <0x0140000 0x7ec0000>;
+ 	};
+ };
+ 

target/linux/kirkwood/patches-5.4/107-03-nsa325.patch

@@ -0,0 +1,54 @@
+--- a/arch/arm/boot/dts/kirkwood-nsa325.dts
++++ b/arch/arm/boot/dts/kirkwood-nsa325.dts
+@@ -15,6 +15,13 @@
+ 	model = "ZyXEL NSA325";
+ 	compatible = "zyxel,nsa325", "marvell,kirkwood-88f6282", "marvell,kirkwood";
+ 
++	aliases {
++		led-boot = &led_green_sys;
++		led-failsafe = &led_orange_sys;
++		led-running = &led_green_sys;
++		led-upgrade = &led_orange_sys;
++	};
++
+ 	memory {
+ 		device_type = "memory";
+ 		reg = <0x00000000 0x20000000>;
+@@ -162,17 +169,19 @@
+ 			     &pmx_led_hdd1_green &pmx_led_hdd1_red>;
+ 		pinctrl-names = "default";
+ 
+-		green-sys {
++		led_green_sys: green-sys {
+ 			label = "nsa325:green:sys";
+ 			gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
++			default-state = "on";
+ 		};
+-		orange-sys {
++		led_orange_sys: orange-sys {
+ 			label = "nsa325:orange:sys";
+ 			gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+ 		};
+ 		green-hdd1 {
+ 			label = "nsa325:green:hdd1";
+ 			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
++			linux,default-trigger = "ata1";
+ 		};
+ 		red-hdd1 {
+ 			label = "nsa325:red:hdd1";
+@@ -181,6 +190,7 @@
+ 		green-hdd2 {
+ 			label = "nsa325:green:hdd2";
+ 			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
++			linux,default-trigger = "ata2";
+ 		};
+ 		red-hdd2 {
+ 			label = "nsa325:red:hdd2";
+@@ -189,6 +199,7 @@
+ 		green-usb {
+ 			label = "nsa325:green:usb";
+ 			gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
++			linux,default-trigger = "usb-host";
+ 		};
+ 		green-copy {
+ 			label = "nsa325:green:copy";

target/linux/kirkwood/patches-5.4/109-pogoplug_v4.patch

@@ -0,0 +1,87 @@
+--- a/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts
++++ b/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts
+@@ -18,12 +18,20 @@
+ 	compatible = "cloudengines,pogoplugv4", "marvell,kirkwood-88f6192",
+ 		     "marvell,kirkwood";
+ 
++	aliases {
++		led-boot = &led_health;
++		led-failsafe = &led_fault;
++		led-running = &led_health;
++		led-upgrade = &led_fault;
++	};
++
+ 	memory {
+ 		device_type = "memory";
+ 		reg = <0x00000000 0x08000000>;
+ 	};
+ 
+ 	chosen {
++		bootargs = "console=ttyS0,115200";
+ 		stdout-path = "uart0:115200n8";
+ 	};
+ 
+@@ -37,8 +45,8 @@
+ 		eject {
+ 			debounce-interval = <50>;
+ 			wakeup-source;
+-			linux,code = <KEY_EJECTCD>;
+-			label = "Eject Button";
++			linux,code = <KEY_RESTART>;
++			label = "Reset";
+ 			gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
+ 		};
+ 	};
+@@ -48,12 +56,12 @@
+ 		pinctrl-0 = <&pmx_led_green &pmx_led_red>;
+ 		pinctrl-names = "default";
+ 
+-		health {
++		led_health: health {
+ 			label = "pogoplugv4:green:health";
+ 			gpios = <&gpio0 22 GPIO_ACTIVE_LOW>;
+ 			default-state = "on";
+ 		};
+-		fault {
++		led_fault: fault {
+ 			label = "pogoplugv4:red:fault";
+ 			gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
+ 		};
+@@ -137,29 +145,19 @@
+ 		#size-cells = <1>;
+ 
+ 		partition@0 {
+-			label = "u-boot";
+-			reg = <0x00000000 0x200000>;
++			label = "uboot";
++			reg = <0x00000000 0x1c0000>;
+ 			read-only;
+ 		};
+ 
+-		partition@200000 {
+-			label = "uImage";
+-			reg = <0x00200000 0x300000>;
+-		};
+-
+-		partition@500000 {
+-			label = "uImage2";
+-			reg = <0x00500000 0x300000>;
+-		};
+-
+-		partition@800000 {
+-			label = "failsafe";
+-			reg = <0x00800000 0x800000>;
++		partition@1c0000 {
++			label = "uboot_env";
++			reg = <0x001c0000 0x40000>;
+ 		};
+ 
+-		partition@1000000 {
+-			label = "root";
+-			reg = <0x01000000 0x7000000>;
++		partition@200000 {
++			label = "ubi";
++			reg = <0x00200000 0x7e00000>;
+ 		};
+ 	};
+ };

target/linux/kirkwood/patches-5.4/110-pogo_e02.patch

@@ -0,0 +1,68 @@
+--- a/arch/arm/boot/dts/kirkwood-pogo_e02.dts
++++ b/arch/arm/boot/dts/kirkwood-pogo_e02.dts
+@@ -20,6 +20,13 @@
+ 	compatible = "cloudengines,pogoe02", "marvell,kirkwood-88f6281",
+ 		     "marvell,kirkwood";
+ 
++	aliases {
++		led-boot = &led_health;
++		led-failsafe = &led_fault;
++		led-running = &led_health;
++		led-upgrade = &led_fault;
++	};
++
+ 	memory {
+ 		device_type = "memory";
+ 		reg = <0x00000000 0x10000000>;
+@@ -33,12 +40,12 @@
+ 	gpio-leds {
+ 		compatible = "gpio-leds";
+ 
+-		health {
++		led_health: health {
+ 			label = "pogo_e02:green:health";
+ 			gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
+-			default-state = "keep";
++			default-state = "on";
+ 		};
+-		fault {
++		led_fault: fault {
+ 			label = "pogo_e02:orange:fault";
+ 			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
+ 		};
+@@ -95,24 +102,24 @@
+ 	status = "okay";
+ 
+ 	partition@0 {
+-		label = "u-boot";
+-		reg = <0x0000000 0x100000>;
++		label = "uboot";
++		reg = <0x0 0xe0000>;
+ 		read-only;
+ 	};
+ 
+-	partition@100000 {
+-		label = "uImage";
+-		reg = <0x0100000 0x400000>;
++	partition@e0000 {
++		label = "uboot_env";
++		reg = <0xe0000 0x20000>;
+ 	};
+ 
+-	partition@500000 {
+-		label = "pogoplug";
+-		reg = <0x0500000 0x2000000>;
++	partition@100000 {
++		label = "second_stage_uboot";
++		reg = <0x100000 0x100000>;
+ 	};
+ 
+-	partition@2500000 {
+-		label = "root";
+-		reg = <0x02500000 0x5b00000>;
++	partition@200000 {
++		label = "ubi";
++		reg = <0x200000 0x7e00000>;
+ 	};
+ };
+ 

target/linux/kirkwood/patches-5.4/111-l-50.patch

@@ -0,0 +1,47 @@
+--- a/arch/arm/boot/dts/kirkwood-l-50.dts
++++ b/arch/arm/boot/dts/kirkwood-l-50.dts
+@@ -18,6 +18,13 @@
+ 		reg = <0x00000000 0x20000000>;
+ 	};
+ 
++	aliases {
++		led-boot = &led_status_green;
++		led-failsafe = &led_status_red;
++		led-running = &led_status_green;
++		led-upgrade = &led_status_red;
++	};
++
+ 	chosen {
+ 		bootargs = "console=ttyS0,115200n8";
+ 		stdout-path = &uart0;
+@@ -95,12 +102,12 @@
+ 	leds {
+ 		compatible = "gpio-leds";
+ 
+-		status_green {
++		led_status_green: status_green {
+ 			label = "l-50:green:status";
+ 			gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
+ 		};
+ 
+-		status_red {
++		led_status_red: status_red {
+ 			label = "l-50:red:status";
+ 			gpios = <&gpio3 2 GPIO_ACTIVE_LOW>;
+ 		};
+@@ -349,13 +356,8 @@
+ 	};
+ 
+ 	partition@100000 {
+-		label = "kernel-1";
+-		reg = <0x00100000 0x00800000>;
+-	};
+-
+-	partition@900000 {
+-		label = "rootfs-1";
+-		reg = <0x00900000 0x07100000>;
++		label = "ubi";
++		reg = <0x00100000 0x07900000>;
+ 	};
+ 
+ 	partition@7a00000 {

target/linux/kirkwood/patches-5.4/112-sheevaplug.patch

@@ -0,0 +1,47 @@
+--- a/arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi
++++ b/arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi
+@@ -78,13 +78,8 @@
+ 	};
+ 
+ 	partition@100000 {
+-		label = "uImage";
+-		reg = <0x0100000 0x400000>;
+-	};
+-
+-	partition@500000 {
+-		label = "root";
+-		reg = <0x0500000 0x1fb00000>;
++		label = "ubi";
++		reg = <0x0100000 0x1ff00000>;
+ 	};
+ };
+ 
+--- a/arch/arm/boot/dts/kirkwood-sheevaplug.dts
++++ b/arch/arm/boot/dts/kirkwood-sheevaplug.dts
+@@ -13,6 +13,13 @@
+ 	model = "Globalscale Technologies SheevaPlug";
+ 	compatible = "globalscale,sheevaplug", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+ 
++	aliases {
++		led-boot = &led_health;
++		led-failsafe = &led_health;
++		led-running = &led_health;
++		led-upgrade = &led_health;
++	};
++
+ 	ocp@f1000000 {
+ 		mvsdio@90000 {
+ 			pinctrl-0 = <&pmx_sdio>;
+@@ -28,10 +35,10 @@
+ 		pinctrl-0 = <&pmx_led_blue &pmx_led_red>;
+ 		pinctrl-names = "default";
+ 
+-		health {
++		led_health: health {
+ 			label = "sheevaplug:blue:health";
+ 			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
+-			default-state = "keep";
++			default-state = "on";
+ 		};
+ 
+ 		misc {

target/linux/kirkwood/patches-5.4/201-enable-sata-port-specific-led-triggers.patch

@@ -0,0 +1,10 @@
+--- a/arch/arm/mach-mvebu/Kconfig
++++ b/arch/arm/mach-mvebu/Kconfig
+@@ -119,6 +119,7 @@ config MACH_DOVE
+ config MACH_KIRKWOOD
+ 	bool "Marvell Kirkwood boards"
+ 	depends on ARCH_MULTI_V5
++	select ARCH_WANT_LIBATA_LEDS
+ 	select CPU_FEROCEON
+ 	select GPIOLIB
+ 	select KIRKWOOD_CLK

target/linux/kirkwood/patches-5.4/202-linksys-find-active-root.patch

@@ -0,0 +1,62 @@
+The WRT1900AC among other Linksys routers uses a dual-firmware layout.
+Dynamically rename the active partition to "ubi".
+
+Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
+---
+--- a/drivers/mtd/parsers/ofpart_core.c
++++ b/drivers/mtd/parsers/ofpart_core.c
+@@ -38,6 +38,8 @@ static bool node_has_compatible(struct d
+ 	return of_get_property(pp, "compatible", NULL);
+ }
+ 
++static int mangled_rootblock;
++
+ static int parse_fixed_partitions(struct mtd_info *master,
+ 				  const struct mtd_partition **pparts,
+ 				  struct mtd_part_parser_data *data)
+@@ -47,6 +49,7 @@ static int parse_fixed_partitions(struct
+ 	struct mtd_partition *parts;
+ 	struct device_node *mtd_node;
+ 	struct device_node *ofpart_node;
++	const char *owrtpart = "ubi";
+ 	const char *partname;
+ 	struct device_node *pp;
+ 	int nr_parts, i, ret = 0;
+@@ -133,9 +136,15 @@ static int parse_fixed_partitions(struct
+ 		parts[i].size = of_read_number(reg + a_cells, s_cells);
+ 		parts[i].of_node = pp;
+ 
+-		partname = of_get_property(pp, "label", &len);
+-		if (!partname)
+-			partname = of_get_property(pp, "name", &len);
++		if (mangled_rootblock && (i == mangled_rootblock)) {
++			partname = owrtpart;
++		} else {
++			partname = of_get_property(pp, "label", &len);
++
++			if (!partname)
++				partname = of_get_property(pp, "name", &len);
++		}
++
+ 		parts[i].name = partname;
+ 
+ 		if (of_get_property(pp, "read-only", &len))
+@@ -249,6 +258,18 @@ static int __init ofpart_parser_init(voi
+ 	return 0;
+ }
+ 
++static int __init active_root(char *str)
++{
++	get_option(&str, &mangled_rootblock);
++
++	if (!mangled_rootblock)
++		return 1;
++
++	return 1;
++}
++
++__setup("mangled_rootblock=", active_root);
++
+ static void __exit ofpart_parser_exit(void)
+ {
+ 	deregister_mtd_parser(&ofpart_parser);

target/linux/kirkwood/patches-5.4/203-blackarmor-nas220.patch

@@ -0,0 +1,99 @@
+--- a/arch/arm/boot/dts/kirkwood-blackarmor-nas220.dts
++++ b/arch/arm/boot/dts/kirkwood-blackarmor-nas220.dts
+@@ -17,6 +17,13 @@
+ 	compatible = "seagate,blackarmor-nas220","marvell,kirkwood-88f6192",
+ 		     "marvell,kirkwood";
+ 
++	aliases {
++		led-boot = &led_status_amber;
++		led-failsafe = &led_status_amber;
++		led-running = &led_status_blue;
++		led-upgrade = &led_status_amber;
++	};
++
+ 	memory { /* 128 MB */
+ 		device_type = "memory";
+ 		reg = <0x00000000 0x8000000>;
+@@ -36,14 +43,14 @@
+ 		compatible = "gpio-keys";
+ 
+ 		reset {
+-			label = "Reset";
+-			linux,code = <KEY_POWER>;
++			label = "Reset Button";
++			linux,code = <KEY_RESTART>;
+ 			gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+ 		};
+ 
+-		button {
+-			label = "Power";
+-			linux,code = <KEY_SLEEP>;
++		power {
++			label = "Power Button";
++			linux,code = <KEY_POWER>;
+ 			gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
+ 		};
+ 	};
+@@ -51,11 +58,27 @@
+ 	gpio-leds {
+ 		compatible = "gpio-leds";
+ 
+-		blue-power {
++		led_power_blue: power_blue {
+ 			label = "nas220:blue:power";
+ 			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+ 			linux,default-trigger = "default-on";
+ 		};
++
++		disk_blue {
++			label = "nas220:blue:disk";
++			gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
++			linux,default-trigger = "disk-activity";
++		};
++
++		led_status_blue: status_blue {
++			label = "nas220:blue:status";
++			gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>;
++		};
++
++		led_status_amber: status_amber {
++			label = "nas220:amber:status";
++			gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
++		};
+ 	};
+ 
+ 	regulators {
+@@ -153,6 +176,33 @@
+ 
+ &nand {
+ 	status = "okay";
++
++	partitions {
++		compatible = "fixed-partitions";
++
++		partition@0 {
++			label = "uboot";
++			reg = <0x0 0xa0000>;
++			read-only;
++		};
++
++		partition@a0000 {
++			label = "uboot-env";
++			reg = <0xa0000 0x10000>;
++			read-only;
++		};
++
++		partition@b0000 {
++			label = "reserved";
++			reg = <0xb0000 0x10000>;
++			read-only;
++		};
++
++		partition@c0000 {
++			label = "ubi";
++			reg = <0xc0000 0x1e80000>;
++		};
++	};
+ };
+ 
+ &mdio {