Initial commit

target/linux/ath79/dts/qca9558_jjplus_jwap230.dts

@@ -0,0 +1,184 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca955x.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "jjPlus JWAP230";
+	compatible = "jjplus,jwap230", "qca,qca9558";
+
+	aliases {
+		led-boot = &led_power;
+		led-failsafe = &led_power;
+		led-running = &led_power;
+		led-upgrade = &led_power;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_power: led-0 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_POWER;
+			gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
+		};
+
+		led-1 {
+			color = <LED_COLOR_ID_GREEN>;
+			function-enumerator = <0>;
+			gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
+		};
+
+		led-2 {
+			color = <LED_COLOR_ID_GREEN>;
+			function-enumerator = <1>;
+			gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+};
+
+&spi {
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <25000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "u-boot";
+				reg = <0x000000 0x040000>;
+				read-only;
+			};
+
+			partition@40000 {
+				label = "u-boot-env";
+				reg = <0x040000 0x010000>;
+			};
+
+			partition@50000 {
+				compatible = "denx,uimage";
+				label = "firmware";
+				reg = <0x050000 0xfa0000>;
+			};
+
+			partition@ff0000 {
+				label = "art";
+				reg = <0xff0000 0x010000>;
+				read-only;
+
+				nvmem-layout {
+					compatible = "fixed-layout";
+					#address-cells = <1>;
+					#size-cells = <1>;
+
+					macaddr_art_lan: macaddr@0 {
+						reg = <0x0 0x6>;
+					};
+
+					macaddr_art_wan: macaddr@6 {
+						reg = <0x6 0x6>;
+					};
+
+					calibration_art_wlan: calibration@1000 {
+						reg = <0x1000 0x440>;
+					};
+				};
+			};
+		};
+	};
+};
+
+&mdio0 {
+	status = "okay";
+
+	switch@0 {
+		compatible = "qca,ar8327";
+		reg = <0>;
+
+		qca,ar8327-initvals = <
+			0x04 0x07600000 /* PORT0 PAD MODE CTRL */
+			0x58 0xffb7ffb7 /* LED_CTRL2 */
+			0x5c 0x03ffff00 /* LED_CTRL3 */
+			0x7c 0x0000007e /* PORT0_STATUS */
+			0x0c 0x00080080 /* PORT6 PAD MODE CTRL */
+			0x94 0x0000007e /* PORT6_STATUS */
+		>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+
+	nvmem-cells = <&macaddr_art_wan>;
+	nvmem-cell-names = "mac-address";
+
+	pll-data = <0xae000000 0x80000101 0x80001313>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+
+	gmac_config: gmac-config {
+		device = <&gmac>;
+
+		rxdv-delay = <3>;
+		rxd-delay = <3>;
+		txen-delay = <0>;
+		txd-delay = <0>;
+		rgmii-enabled = <1>;
+	};
+};
+
+&eth1 {
+	status = "okay";
+
+	nvmem-cells = <&macaddr_art_lan>;
+	nvmem-cell-names = "mac-address";
+
+	pll-data = <0x03000101 0x00000101 0x00001313>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&wmac {
+	status = "okay";
+	nvmem-cells = <&calibration_art_wlan>;
+	nvmem-cell-names = "calibration";
+};
+
+&usb_phy0 {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&usb_phy1 {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};