Netgear R6100 support
Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 43382
This commit is contained in:
Imre Kaloz
@@ -263,6 +263,7 @@ get_status_led() {
|
||||
wzr-hp-g300nh2)
|
||||
status_led="buffalo:red:diag"
|
||||
;;
|
||||
r6100 | \
|
||||
wndap360 | \
|
||||
wndr3700 | \
|
||||
wndr3700v4 | \
|
||||
|
||||
@@ -38,6 +38,7 @@ board=$(ar71xx_board_name)
|
||||
case "$FIRMWARE" in
|
||||
"soc_wmac.eeprom")
|
||||
case $board in
|
||||
r6100 | \
|
||||
wndr3700v4 | \
|
||||
wndr4300)
|
||||
ath9k_eeprom_extract "caldata" 4096 2048
|
||||
|
||||
@@ -421,6 +421,12 @@ wndr3700)
|
||||
ucidef_set_led_usbdev "usb" "USB" "netgear:green:usb" "1-1"
|
||||
;;
|
||||
|
||||
r6100)
|
||||
ucidef_set_led_netdev "wan" "WAN (green)" "netgear:green:wan" "eth0.2"
|
||||
ucidef_set_led_usbdev "usb" "USB" "netgear:blue:usb" "1-1"
|
||||
ucidef_set_led_wlan "wlan" "WLAN" "netgear:blue:wlan" "phy1tpt"
|
||||
;;
|
||||
|
||||
wndr3700v4 | \
|
||||
wndr4300)
|
||||
ucidef_set_led_netdev "wan" "WAN (green)" "netgear:green:wan" "eth0.2"
|
||||
|
||||
@@ -201,7 +201,8 @@ tl-wr941nd)
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan"
|
||||
;;
|
||||
|
||||
smart-300 | \
|
||||
r6100 |\
|
||||
smart-300 |\
|
||||
tl-mr3420-v2 |\
|
||||
tl-wr841n-v8 |\
|
||||
tl-wr842n-v2 |\
|
||||
|
||||
@@ -701,6 +701,9 @@ ar71xx_board_detect() {
|
||||
*"WNDR3700/WNDR3800/WNDRMAC")
|
||||
wndr3700_board_detect "$machine"
|
||||
;;
|
||||
*"R6100")
|
||||
name="r6100"
|
||||
;;
|
||||
*"WNDR3700v4")
|
||||
name="wndr3700v4"
|
||||
;;
|
||||
|
||||
@@ -29,6 +29,12 @@ preinit_set_mac_address() {
|
||||
fetch_mac_from_mtd config lan_mac wan_mac
|
||||
echo 1 > /sys/class/leds/dir-615-c1:green:wancpu/brightness
|
||||
;;
|
||||
r6100)
|
||||
mac_lan=$(mtd_get_mac_binary caldata 0)
|
||||
[ -n "$mac_lan" ] && ifconfig eth1 hw ether "$mac_lan"
|
||||
mac_wan=$(mtd_get_mac_binary caldata 6)
|
||||
[ -n "$mac_wan" ] && ifconfig eth0 hw ether "$mac_wan"
|
||||
;;
|
||||
wrt160nl)
|
||||
fetch_mac_from_mtd nvram lan_hwaddr wan_hwaddr
|
||||
;;
|
||||
|
||||
@@ -22,7 +22,17 @@ do_load_ath10k_board_bin() {
|
||||
macaddr_2bin $mac >> /tmp/ath10k-board.bin
|
||||
dd if=/dev/mtdblock4 \
|
||||
bs=1 skip=20492 count=2104 >> /tmp/ath10k-board.bin
|
||||
;;
|
||||
r6100)
|
||||
local mac
|
||||
mac=$(macaddr_add $(cat /sys/class/net/eth1/address) +2)
|
||||
|
||||
dd if=/dev/mtdblock2 \
|
||||
bs=1 skip=20480 count=6 \
|
||||
of=/tmp/ath10k-board.bin
|
||||
macaddr_2bin $mac >> /tmp/ath10k-board.bin
|
||||
dd if=/dev/mtdblock2 \
|
||||
bs=1 skip=20492 count=2104 >> /tmp/ath10k-board.bin
|
||||
;;
|
||||
qihoo-c301)
|
||||
local mac
|
||||
|
||||
@@ -354,6 +354,7 @@ platform_check_image() {
|
||||
return 0
|
||||
;;
|
||||
nbg6716 | \
|
||||
r6100 | \
|
||||
wndr3700v4 | \
|
||||
wndr4300 )
|
||||
nand_do_platform_check $board $1
|
||||
|
||||
@@ -76,6 +76,7 @@ CONFIG_ATH79_MACH_PB42=y
|
||||
CONFIG_ATH79_MACH_PB44=y
|
||||
CONFIG_ATH79_MACH_PB92=y
|
||||
CONFIG_ATH79_MACH_QIHOO_C301=y
|
||||
CONFIG_ATH79_MACH_R6100=y
|
||||
# CONFIG_ATH79_MACH_RB2011 is not set
|
||||
# CONFIG_ATH79_MACH_RB4XX is not set
|
||||
# CONFIG_ATH79_MACH_RB750 is not set
|
||||
|
||||
146
target/linux/ar71xx/files/arch/mips/ath79/mach-r6100.c
Normal file
146
target/linux/ar71xx/files/arch/mips/ath79/mach-r6100.c
Normal file
@@ -0,0 +1,146 @@
|
||||
/*
|
||||
* NETGEAR R6100 board support
|
||||
*
|
||||
* Copyright (C) 2014 Gabor Juhos <juhosg@openwrt.org>
|
||||
* Copyright (C) 2014 Imre Kaloz <kaloz@openwrt.org>
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify it
|
||||
* under the terms of the GNU General Public License version 2 as published
|
||||
* by the Free Software Foundation.
|
||||
*/
|
||||
|
||||
#include <linux/pci.h>
|
||||
#include <linux/phy.h>
|
||||
#include <linux/gpio.h>
|
||||
#include <linux/platform_device.h>
|
||||
#include <linux/ath9k_platform.h>
|
||||
#include <linux/platform/ar934x_nfc.h>
|
||||
|
||||
#include <asm/mach-ath79/ar71xx_regs.h>
|
||||
|
||||
#include "common.h"
|
||||
#include "dev-ap9x-pci.h"
|
||||
#include "dev-eth.h"
|
||||
#include "dev-gpio-buttons.h"
|
||||
#include "dev-leds-gpio.h"
|
||||
#include "dev-nfc.h"
|
||||
#include "dev-usb.h"
|
||||
#include "dev-wmac.h"
|
||||
#include "machtypes.h"
|
||||
|
||||
#define R6100_GPIO_LED_WLAN 0
|
||||
#define R6100_GPIO_LED_USB 11
|
||||
#define R6100_GPIO_LED_WAN_GREEN 13
|
||||
#define R6100_GPIO_LED_POWER_AMBER 14
|
||||
#define R6100_GPIO_LED_WAN_AMBER 15
|
||||
#define R6100_GPIO_LED_POWER_GREEN 17
|
||||
|
||||
#define R6100_GPIO_BTN_WIRELESS 1
|
||||
#define R6100_GPIO_BTN_WPS 3
|
||||
#define R6100_GPIO_BTN_RESET 12
|
||||
|
||||
#define R6100_GPIO_USB_POWER 16
|
||||
|
||||
#define R6100_KEYS_POLL_INTERVAL 20 /* msecs */
|
||||
#define R6100_KEYS_DEBOUNCE_INTERVAL (3 * R6100_KEYS_POLL_INTERVAL)
|
||||
|
||||
static struct gpio_led r6100_leds_gpio[] __initdata = {
|
||||
{
|
||||
.name = "netgear:green:power",
|
||||
.gpio = R6100_GPIO_LED_POWER_GREEN,
|
||||
.active_low = 1,
|
||||
},
|
||||
{
|
||||
.name = "netgear:amber:power",
|
||||
.gpio = R6100_GPIO_LED_POWER_AMBER,
|
||||
.active_low = 1,
|
||||
},
|
||||
{
|
||||
.name = "netgear:green:wan",
|
||||
.gpio = R6100_GPIO_LED_WAN_GREEN,
|
||||
.active_low = 1,
|
||||
},
|
||||
{
|
||||
.name = "netgear:amber:wan",
|
||||
.gpio = R6100_GPIO_LED_WAN_AMBER,
|
||||
.active_low = 1,
|
||||
},
|
||||
{
|
||||
.name = "netgear:blue:usb",
|
||||
.gpio = R6100_GPIO_LED_USB,
|
||||
.active_low = 1,
|
||||
},
|
||||
{
|
||||
.name = "netgear:blue:wlan",
|
||||
.gpio = R6100_GPIO_LED_WLAN,
|
||||
.active_low = 1,
|
||||
},
|
||||
};
|
||||
|
||||
static struct gpio_keys_button r6100_gpio_keys[] __initdata = {
|
||||
{
|
||||
.desc = "Reset button",
|
||||
.type = EV_KEY,
|
||||
.code = KEY_RESTART,
|
||||
.debounce_interval = R6100_KEYS_DEBOUNCE_INTERVAL,
|
||||
.gpio = R6100_GPIO_BTN_RESET,
|
||||
.active_low = 0,
|
||||
},
|
||||
{
|
||||
.desc = "WPS button",
|
||||
.type = EV_KEY,
|
||||
.code = KEY_WPS_BUTTON,
|
||||
.debounce_interval = R6100_KEYS_DEBOUNCE_INTERVAL,
|
||||
.gpio = R6100_GPIO_BTN_WPS,
|
||||
.active_low = 0,
|
||||
},
|
||||
{
|
||||
.desc = "RFKILL switch",
|
||||
.type = EV_SW,
|
||||
.code = KEY_RFKILL,
|
||||
.debounce_interval = R6100_KEYS_DEBOUNCE_INTERVAL,
|
||||
.gpio = R6100_GPIO_BTN_WIRELESS,
|
||||
.active_low = 0,
|
||||
},
|
||||
};
|
||||
|
||||
static void __init r6100_setup(void)
|
||||
{
|
||||
ath79_register_leds_gpio(-1, ARRAY_SIZE(r6100_leds_gpio),
|
||||
r6100_leds_gpio);
|
||||
ath79_register_gpio_keys_polled(-1, R6100_KEYS_POLL_INTERVAL,
|
||||
ARRAY_SIZE(r6100_gpio_keys),
|
||||
r6100_gpio_keys);
|
||||
|
||||
ath79_setup_ar934x_eth_cfg(AR934X_ETH_CFG_SW_PHY_SWAP);
|
||||
|
||||
ath79_register_mdio(1, 0x0);
|
||||
|
||||
/* GMAC0 is connected to the PHY0 of the internal switch */
|
||||
ath79_switch_data.phy4_mii_en = 1;
|
||||
ath79_switch_data.phy_poll_mask = BIT(0);
|
||||
ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_MII;
|
||||
ath79_eth0_data.phy_mask = BIT(0);
|
||||
ath79_eth0_data.mii_bus_dev = &ath79_mdio1_device.dev;
|
||||
ath79_register_eth(0);
|
||||
|
||||
/* GMAC1 is connected to the internal switch */
|
||||
ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_GMII;
|
||||
ath79_register_eth(1);
|
||||
|
||||
gpio_request_one(R6100_GPIO_USB_POWER,
|
||||
GPIOF_OUT_INIT_HIGH | GPIOF_EXPORT_DIR_FIXED,
|
||||
"USB power");
|
||||
|
||||
ath79_nfc_set_ecc_mode(AR934X_NFC_ECC_HW);
|
||||
ath79_register_nfc();
|
||||
|
||||
ath79_register_usb();
|
||||
|
||||
ath79_register_wmac_simple();
|
||||
|
||||
ap91_pci_init_simple();
|
||||
}
|
||||
|
||||
MIPS_MACHINE(ATH79_MACH_R6100, "R6100", "NETGEAR R6100",
|
||||
r6100_setup);
|
||||
@@ -301,6 +301,7 @@ wnr2000v3_mtdlayout=mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,3712k(firmw
|
||||
wnr2000v4_mtdlayout=mtdparts=spi0.0:192k(u-boot)ro,64k(u-boot-env)ro,3776k(firmware),64k(art)ro
|
||||
wndr3700_mtdlayout=mtdparts=spi0.0:320k(u-boot)ro,128k(u-boot-env)ro,7680k(firmware),64k(art)ro
|
||||
wndr3700v2_mtdlayout=mtdparts=spi0.0:320k(u-boot)ro,128k(u-boot-env)ro,15872k(firmware),64k(art)ro
|
||||
r6100_mtdlayout=mtdparts=ar934x-nfc:128k(u-boot)ro,256k(caldata),256k(caldata-backup),512k(config),512k(pot),2048k(kernel),122240k(ubi),25600k@0x1a0000(firmware),2048k(language),3072k(traffic_meter)
|
||||
wndr4300_mtdlayout=mtdparts=ar934x-nfc:256k(u-boot)ro,256k(u-boot-env)ro,256k(caldata),512k(pot),2048k(language),512k(config),3072k(traffic_meter),2048k(kernel),23552k(ubi),25600k@0x6c0000(firmware),256k(caldata_backup),-(reserved)
|
||||
zcn1523h_mtdlayout=mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,6208k(rootfs),1472k(kernel),64k(configure)ro,64k(mfg)ro,64k(art)ro,7680k@0x50000(firmware)
|
||||
mynet_n600_mtdlayout=mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,64k(devdata)ro,64k(devconf)ro,15872k(firmware),64k(radiocfg)ro
|
||||
@@ -1343,6 +1344,7 @@ endif # ifeq ($(SUBTARGET),generic)
|
||||
ifeq ($(SUBTARGET),nand)
|
||||
$(eval $(call SingleProfile,NetgearNAND,64k,WNDR3700V4,wndr3700v4,WNDR3700_V4,ttyS0,115200,$$(wndr4300_mtdlayout),0x33373033,WNDR3700v4,"",-H 29763948+128+128,wndr4300))
|
||||
$(eval $(call SingleProfile,NetgearNAND,64k,WNDR4300V1,wndr4300,WNDR4300,ttyS0,115200,$$(wndr4300_mtdlayout),0x33373033,WNDR4300,"",-H 29763948+0+128+128+2x2+3x3,wndr4300))
|
||||
$(eval $(call SingleProfile,NetgearNAND,64k,R6100,r6100,R6100,ttyS0,115200,$$(r6100_mtdlayout),0x36303030,R6100,"",-H 29764434+0+128+128+2x2+2x2,wndr4300))
|
||||
|
||||
$(eval $(call SingleProfile,ZyXELNAND,128k,NBG6716,nbg6716,NBG6716,ttyS0,115200,NBG6716,$$(zyx_nbg6716_mtdlayout),mem=256M))
|
||||
|
||||
|
||||
@@ -1,10 +1,22 @@
|
||||
#
|
||||
# Copyright (C) 2009-2013 OpenWrt.org
|
||||
# Copyright (C) 2009-2014 OpenWrt.org
|
||||
#
|
||||
# This is free software, licensed under the GNU General Public License v2.
|
||||
# See /LICENSE for more information.
|
||||
#
|
||||
|
||||
define Profile/R6100
|
||||
NAME:=NETGEAR R6100
|
||||
PACKAGES:=kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-ledtrig-usbdev
|
||||
endef
|
||||
|
||||
define Profile/R6100/Description
|
||||
Package set optimized for the NETGEAR R6100
|
||||
endef
|
||||
|
||||
$(eval $(call Profile,R6100))
|
||||
|
||||
|
||||
define Profile/WNDR4300
|
||||
NAME:=NETGEAR WNDR3700v4/WNDR4300
|
||||
PACKAGES:=kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-ledtrig-usbdev
|
||||
@@ -15,5 +27,3 @@ define Profile/WNDR4300/Description
|
||||
endef
|
||||
|
||||
$(eval $(call Profile,WNDR4300))
|
||||
|
||||
|
||||
|
||||
@@ -0,0 +1,40 @@
|
||||
--- a/arch/mips/ath79/Kconfig
|
||||
+++ b/arch/mips/ath79/Kconfig
|
||||
@@ -483,6 +483,17 @@ config ATH79_MACH_WRT400N
|
||||
select ATH79_DEV_LEDS_GPIO
|
||||
select ATH79_DEV_M25P80
|
||||
|
||||
+config ATH79_MACH_R6100
|
||||
+ bool "NETGEAR R6100 board support"
|
||||
+ select SOC_AR934X
|
||||
+ select ATH79_DEV_AP9X_PCI if PCI
|
||||
+ select ATH79_DEV_ETH
|
||||
+ select ATH79_DEV_GPIO_BUTTONS
|
||||
+ select ATH79_DEV_LEDS_GPIO
|
||||
+ select ATH79_DEV_NFC
|
||||
+ select ATH79_DEV_USB
|
||||
+ select ATH79_DEV_WMAC
|
||||
+
|
||||
config ATH79_MACH_RB4XX
|
||||
bool "MikroTik RouterBOARD 4xx series support"
|
||||
select SOC_AR71XX
|
||||
--- a/arch/mips/ath79/Makefile
|
||||
+++ b/arch/mips/ath79/Makefile
|
||||
@@ -88,6 +88,7 @@ obj-$(CONFIG_ATH79_MACH_PB42) += mach-p
|
||||
obj-$(CONFIG_ATH79_MACH_PB44) += mach-pb44.o
|
||||
obj-$(CONFIG_ATH79_MACH_PB92) += mach-pb92.o
|
||||
obj-$(CONFIG_ATH79_MACH_QIHOO_C301) += mach-qihoo-c301.o
|
||||
+obj-$(CONFIG_ATH79_MACH_R6100) += mach-r6100.o
|
||||
obj-$(CONFIG_ATH79_MACH_RB4XX) += mach-rb4xx.o
|
||||
obj-$(CONFIG_ATH79_MACH_RB750) += mach-rb750.o
|
||||
obj-$(CONFIG_ATH79_MACH_RB91X) += mach-rb91x.o
|
||||
--- a/arch/mips/ath79/machtypes.h
|
||||
+++ b/arch/mips/ath79/machtypes.h
|
||||
@@ -84,6 +84,7 @@ enum ath79_mach_type {
|
||||
ATH79_MACH_PB42, /* Atheros PB42 */
|
||||
ATH79_MACH_PB92, /* Atheros PB92 */
|
||||
ATH79_MACH_QIHOO_C301, /* Qihoo 360 C301 */
|
||||
+ ATH79_MACH_R6100, /* NETGEAR R6100 */
|
||||
ATH79_MACH_RB_411, /* MikroTik RouterBOARD 411/411A/411AH */
|
||||
ATH79_MACH_RB_411U, /* MikroTik RouterBOARD 411U */
|
||||
ATH79_MACH_RB_433, /* MikroTik RouterBOARD 433/433AH */
|
||||
Reference in New Issue
Block a user