mediatek: add support for the GL.iNet GL-MT3000
The MT-3000 is a pocket-sized Wi-Fi 6 router based on MediaTek MT7981.
Specification:
- SoC: MediaTek MT7981B
- CPU: 2x 1.3 GHz Cortex-A53
- Flash: 256 MiB Macronix SPI NAND
- RAM: 512 MiB Nanya DDR4
- WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN)
- Ethernet:
- 1x 10/100/1000 Mbps built-in PHY (LAN)
- 1x 10/100/1000/2500 Mbps MaxLinear GPY211 PHY (WAN)
- USB 3.0 port
- Buttons: 1 button, 1 switch
- LEDs: 1x light-blue, 1x warm-white
- Serial console: internal 4-pin header, 115200 8n1
- PWM controlled fan with tacho
- Power: 5 VDC, 3 A (USB Type-C)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This commit is contained in:
Daniel Golle
@@ -1,11 +1,15 @@
|
||||
set_preinit_iface() {
|
||||
ip link set eth0 up
|
||||
|
||||
case $(board_name) in
|
||||
glinet,gl-mt3000)
|
||||
ip link set eth1 up
|
||||
ifname=eth1
|
||||
;;
|
||||
ubnt,unifi-6-lr)
|
||||
ip link set eth0 up
|
||||
ifname=eth0
|
||||
;;
|
||||
*)
|
||||
ip link set eth0 up
|
||||
ifname=lan1
|
||||
;;
|
||||
esac
|
||||
|
||||
240
target/linux/mediatek/dts/mt7981b-glinet-gl-mt3000.dts
Normal file
240
target/linux/mediatek/dts/mt7981b-glinet-gl-mt3000.dts
Normal file
@@ -0,0 +1,240 @@
|
||||
/dts-v1/;
|
||||
|
||||
#include "mt7981.dtsi"
|
||||
|
||||
/ {
|
||||
model = "GL.iNet GL-MT3000";
|
||||
compatible = "glinet,gl-mt3000", "mediatek,mt7981";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_lightblue;
|
||||
led-failsafe = &led_lightblue;
|
||||
led-running = &led_white;
|
||||
led-upgrade = &led_lightblue;
|
||||
serial0 = &uart0;
|
||||
};
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&pio 1 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
mode {
|
||||
label = "mode";
|
||||
linux,input-type = <EV_SW>;
|
||||
linux,code = <BTN_0>;
|
||||
gpios = <&pio 0 GPIO_ACTIVE_HIGH>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_lightblue: led@0 {
|
||||
label = "blue:run";
|
||||
gpios = <&pio 31 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_white: led@1 {
|
||||
label = "white:system";
|
||||
gpios = <&pio 30 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
fan_5v: regulator-fan-5v {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "fan";
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
gpio = <&pio 28 GPIO_ACTIVE_HIGH>;
|
||||
enable-active-high;
|
||||
regulator-boot-on;
|
||||
};
|
||||
|
||||
usb_vbus: regulator-usb-vbus {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "usb_vbus";
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
gpio = <&pio 12 GPIO_ACTIVE_HIGH>;
|
||||
enable-active-high;
|
||||
regulator-boot-on;
|
||||
};
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&watchdog {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ð {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&mdio_pins>;
|
||||
|
||||
status = "okay";
|
||||
|
||||
gmac0: mac@0 {
|
||||
compatible = "mediatek,eth-mac";
|
||||
reg = <0>;
|
||||
phy-mode = "2500base-x";
|
||||
phy-handle = <&phy0>;
|
||||
nvmem-cells = <&macaddr>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
gmac1: mac@1 {
|
||||
compatible = "mediatek,eth-mac";
|
||||
reg = <1>;
|
||||
phy-mode = "gmii";
|
||||
phy-handle = <&int_gbe_phy>;
|
||||
nvmem-cells = <&macaddr>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
mac-address-increment = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
&mdio_bus {
|
||||
reset-gpios = <&pio 14 GPIO_ACTIVE_LOW>;
|
||||
reset-delay-us = <600>;
|
||||
reset-post-delay-us = <20000>;
|
||||
|
||||
phy0: ethernet-phy@5 {
|
||||
reg = <5>;
|
||||
compatible = "ethernet-phy-ieee802.3-c45";
|
||||
phy-mode = "2500base-x";
|
||||
};
|
||||
};
|
||||
|
||||
&pwm {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pwm_pins>;
|
||||
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&fan {
|
||||
pwms = <&pwm 0 40000 0>;
|
||||
fan-supply = <&fan_5v>;
|
||||
interrupt-parent = <&pio>;
|
||||
interrupts = <29 IRQ_TYPE_EDGE_RISING>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&spi0_flash_pins>;
|
||||
status = "okay";
|
||||
|
||||
spi_nand: flash@0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
compatible = "spi-nand";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <52000000>;
|
||||
|
||||
spi-cal-enable;
|
||||
spi-cal-mode = "read-data";
|
||||
spi-cal-datalen = <7>;
|
||||
spi-cal-data = /bits/ 8 <0x53 0x50 0x49 0x4E 0x41 0x4E 0x44>;
|
||||
spi-cal-addrlen = <5>;
|
||||
spi-cal-addr = /bits/ 32 <0x0 0x0 0x0 0x0 0x0>;
|
||||
|
||||
spi-tx-buswidth = <4>;
|
||||
spi-rx-buswidth = <4>;
|
||||
mediatek,nmbm;
|
||||
mediatek,bmt-max-ratio = <1>;
|
||||
mediatek,bmt-max-reserved-blocks = <64>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "BL2";
|
||||
reg = <0x00000 0x0100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x0100000 0x0080000>;
|
||||
};
|
||||
|
||||
factory: partition@180000 {
|
||||
label = "Factory";
|
||||
reg = <0x180000 0x0200000>;
|
||||
read-only;
|
||||
|
||||
compatible = "nvmem-cells";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
macaddr: macaddr@a {
|
||||
reg = <0xa 0x6>;
|
||||
};
|
||||
};
|
||||
|
||||
partition@380000 {
|
||||
label = "FIP";
|
||||
reg = <0x380000 0x0200000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@580000 {
|
||||
label = "log";
|
||||
reg = <0x580000 0x0040000>;
|
||||
};
|
||||
|
||||
partition@5c0000 {
|
||||
label = "ubi";
|
||||
reg = <0x5c0000 0xf640000>;
|
||||
compatible = "linux,ubi";
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pio {
|
||||
spi0_flash_pins: spi0-pins {
|
||||
mux {
|
||||
function = "spi";
|
||||
groups = "spi0", "spi0_wp_hold";
|
||||
};
|
||||
};
|
||||
|
||||
pwm_pins: pwm0-pins {
|
||||
mux {
|
||||
function = "pwm";
|
||||
groups = "pwm0_1";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&usb_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&xhci {
|
||||
vbus-supply = <&usb_vbus>;
|
||||
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wifi {
|
||||
mediatek,mtd-eeprom = <&factory 0x0>;
|
||||
|
||||
status = "okay";
|
||||
};
|
||||
@@ -17,6 +17,9 @@ mediatek_setup_interfaces()
|
||||
cudy,wr3000-v1)
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" "wan"
|
||||
;;
|
||||
glinet,gl-mt3000)
|
||||
ucidef_set_interfaces_lan_wan eth1 eth0
|
||||
;;
|
||||
mediatek,mt7986a-rfb)
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 lan6" "eth1 wan"
|
||||
;;
|
||||
|
||||
@@ -36,6 +36,36 @@ define Build/mt7986-gpt
|
||||
rm $@.tmp
|
||||
endef
|
||||
|
||||
metadata_gl_json = \
|
||||
'{ $(if $(IMAGE_METADATA),$(IMAGE_METADATA)$(comma)) \
|
||||
"metadata_version": "1.1", \
|
||||
"compat_version": "$(call json_quote,$(compat_version))", \
|
||||
$(if $(DEVICE_COMPAT_MESSAGE),"compat_message": "$(call json_quote,$(DEVICE_COMPAT_MESSAGE))"$(comma)) \
|
||||
$(if $(filter-out 1.0,$(compat_version)),"new_supported_devices": \
|
||||
[$(call metadata_devices,$(SUPPORTED_DEVICES))]$(comma) \
|
||||
"supported_devices": ["$(call json_quote,$(legacy_supported_message))"]$(comma)) \
|
||||
$(if $(filter 1.0,$(compat_version)),"supported_devices":[$(call metadata_devices,$(SUPPORTED_DEVICES))]$(comma)) \
|
||||
"version": { \
|
||||
"release": "$(call json_quote,$(VERSION_NUMBER))", \
|
||||
"date": "$(shell TZ='Asia/Chongqing' date '+%Y%m%d%H%M%S')", \
|
||||
"dist": "$(call json_quote,$(VERSION_DIST))", \
|
||||
"version": "$(call json_quote,$(VERSION_NUMBER))", \
|
||||
"revision": "$(call json_quote,$(REVISION))", \
|
||||
"target": "$(call json_quote,$(TARGETID))", \
|
||||
"board": "$(call json_quote,$(if $(BOARD_NAME),$(BOARD_NAME),$(DEVICE_NAME)))" \
|
||||
}, \
|
||||
"upgrade_control":"$(shell python3 $(TOPDIR)/make_gl_metadata.py)", \
|
||||
"release_note":"$(shell sed ':a;N;s/\n/\\n/g;s/\r/\\r/g;ta' $(TOPDIR)/gl_release_note)" \
|
||||
}'
|
||||
|
||||
define Build/append-gl-metadata
|
||||
$(if $(SUPPORTED_DEVICES),-echo $(call metadata_gl_json,$(SUPPORTED_DEVICES)) | fwtool -I - $@)
|
||||
[ ! -s "$(BUILD_KEY)" -o ! -s "$@" ] || { \
|
||||
usign -S -m "$@" -s "$(BUILD_KEY)" -x "$@.sig" ;\
|
||||
fwtool -S "$@.sig" "$@" ;\
|
||||
}
|
||||
endef
|
||||
|
||||
define Device/asus_tuf-ax4200
|
||||
DEVICE_VENDOR := ASUS
|
||||
DEVICE_MODEL := TUF-AX4200
|
||||
@@ -52,7 +82,6 @@ define Device/asus_tuf-ax4200
|
||||
endef
|
||||
TARGET_DEVICES += asus_tuf-ax4200
|
||||
|
||||
|
||||
define Device/bananapi_bpi-r3
|
||||
DEVICE_VENDOR := Bananapi
|
||||
DEVICE_MODEL := BPi-R3
|
||||
@@ -119,6 +148,22 @@ define Device/cudy_wr3000-v1
|
||||
endef
|
||||
TARGET_DEVICES += cudy_wr3000-v1
|
||||
|
||||
define Device/glinet_gl-mt3000
|
||||
DEVICE_VENDOR := GL.iNet
|
||||
DEVICE_MODEL := GL-MT3000
|
||||
DEVICE_DTS := mt7981b-glinet-gl-mt3000
|
||||
DEVICE_DTS_DIR := ../dts
|
||||
SUPPORTED_DEVICES += glinet,mt3000-snand
|
||||
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware kmod-hwmon-pwmfan kmod-usb3
|
||||
UBINIZE_OPTS := -E 5
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
IMAGE_SIZE := 246272k
|
||||
KERNEL_IN_UBI := 1
|
||||
IMAGE/sysupgrade.bin := sysupgrade-tar | append-gl-metadata
|
||||
endef
|
||||
TARGET_DEVICES += glinet_gl-mt3000
|
||||
|
||||
define Device/mediatek_mt7986a-rfb-nand
|
||||
DEVICE_VENDOR := MediaTek
|
||||
DEVICE_MODEL := MT7986 rfba AP (NAND)
|
||||
|
||||
Reference in New Issue
Block a user