mvebu: cortexa9: Add support for Ctera C200-V2
2-Bay NAS - maximum two 3.5" Harddisks
Hardware:
- SoC: Marvell 88F6707-A1 ARMv7 Processor 1,2GHz (ARMADA 370 SoC)
- Ram: 1GB (2x Nanya NT5CC512M8DN-D1)
- NAND Flash: 256MB (ESMT F59L2G81A-25T)
- Lan: 1x GBE (Marvell 88E1318-NNB2)
- Storage: 2x SATA HDD 3.5" Slot
- USB: 2x USB 3.0 port (Renesas uPD720202)
- Console: Internal J3 connector (1: Vcc, 2: Rx, 3: Tx, 4: GND)
- LEDs: 13x GPIO controlled
- Buttons: 2x GPIO controlled
Known issues:
- Buzzer is unused due lack of proper driver
- USB1/2 usbport ledtrigger won't work (through DT)
- Renesas uPD720202 requires firmware file. It's possible to find
non-free binary. Please look for 'UPDATE.mem' file and put in into
'/lib/firmware/renesas_usb_fw.mem' file.
Installation:
- Apply factory initramfs image via stock web-gui.
- Do sysupgrade to make installation complete.
Back to stock:
- OpenWrt rootfs partition use unused space after stock firmware.
- Full revert is possible.
- Login via ssh and run:
## ctera_c200-v2_back_to_factory start ##
. /lib/functions.sh
part=$(find_mtd_part "active_bank")
active_bank=$(strings "$part" | grep bank)
if [ "$active_bank" = "bank1" ]; then
echo "bank2" > /tmp/change_bank
else
echo "bank1" > /tmp/change_bank
fi
mtd write /tmp/change_bank active_bank
reboot
## ctera_c200-v2_back_to_factory end ##
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
(put back-to-stock script into commit message, removed dup. SUBPAGESIZE var,
added 01_leds for non-working dt-usb-port trigger)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This commit is contained in:
Pawel Dembicki
committed by
Christian Lamparter
Christian Lamparter
parent
1ed50b92d1
commit
9149ed4f05
@@ -1712,7 +1712,8 @@ define KernelPackage/usb3
|
||||
+TARGET_bcm53xx:kmod-usb-bcma \
|
||||
+TARGET_bcm53xx:kmod-phy-bcm-ns-usb3 \
|
||||
+TARGET_ramips_mt7621:kmod-usb-xhci-mtk \
|
||||
+(TARGET_apm821xx_nand&&LINUX_5_10):kmod-usb-xhci-pci-renesas
|
||||
+(TARGET_apm821xx_nand&&LINUX_5_10):kmod-usb-xhci-pci-renesas \
|
||||
+TARGET_mvebu_cortexa9:kmod-usb-xhci-pci-renesas
|
||||
KCONFIG:= \
|
||||
CONFIG_USB_PCI=y \
|
||||
CONFIG_USB_XHCI_PCI \
|
||||
|
||||
@@ -337,6 +337,9 @@ CONFIG_PJ4B_ERRATA_4742=y
|
||||
CONFIG_PL310_ERRATA_753970=y
|
||||
CONFIG_PLAT_ORION=y
|
||||
CONFIG_PM_OPP=y
|
||||
CONFIG_POWER_RESET=y
|
||||
CONFIG_POWER_RESET_GPIO=y
|
||||
# CONFIG_POWER_RESET_QNAP is not set
|
||||
CONFIG_PRINTK_SAFE_LOG_BUF_SHIFT=11
|
||||
CONFIG_PWM=y
|
||||
CONFIG_PWM_SYSFS=y
|
||||
|
||||
@@ -11,6 +11,10 @@ board=$(board_name)
|
||||
boardname="${board##*,}"
|
||||
|
||||
case "$board" in
|
||||
ctera,c200-v2
|
||||
ucidef_set_led_usbport "usb2" "USB2" "green:usb-2" "usb1-port1" "usb2-port1"
|
||||
ucidef_set_led_usbport "usb3" "USB3" "green:usb-1" "usb1-port2" "usb2-port2"
|
||||
;;
|
||||
kobol,helios4)
|
||||
ucidef_set_led_usbport "USB" "USB" "helios4:green:usb" "usb1-port1" "usb2-port1" "usb3-port1" "usb4-port1" "usb5-port1"
|
||||
;;
|
||||
|
||||
@@ -12,6 +12,9 @@ mvebu_setup_interfaces()
|
||||
local board="$1"
|
||||
|
||||
case "$board" in
|
||||
ctera,c200-v2)
|
||||
ucidef_set_interface_lan "eth0" "dhcp"
|
||||
;;
|
||||
cznic,turris-omnia)
|
||||
ucidef_set_interfaces_lan_wan "lan0 lan1 lan2 lan3 lan4" "eth2"
|
||||
;;
|
||||
@@ -58,6 +61,10 @@ mvebu_setup_macs()
|
||||
buffalo,ls421de)
|
||||
lan_mac=$(mtd_get_mac_ascii u-boot-env eth1addr)
|
||||
;;
|
||||
ctera,c200-v2)
|
||||
label_mac=$(mtd_get_mac_ascii dev_params mac)
|
||||
lan_mac=$label_mac
|
||||
;;
|
||||
linksys,wrt1200ac|\
|
||||
linksys,wrt1900ac-v2|\
|
||||
linksys,wrt1900acs|\
|
||||
|
||||
@@ -3,7 +3,7 @@
|
||||
# Copyright (C) 2016 LEDE-Project.org
|
||||
#
|
||||
|
||||
RAMFS_COPY_BIN='fw_printenv fw_setenv'
|
||||
RAMFS_COPY_BIN='fw_printenv fw_setenv strings'
|
||||
RAMFS_COPY_DATA='/etc/fw_env.config /var/lock/fw_printenv.lock'
|
||||
REQUIRE_IMAGE_METADATA=1
|
||||
|
||||
@@ -26,6 +26,17 @@ platform_do_upgrade() {
|
||||
buffalo,ls421de)
|
||||
nand_do_upgrade "$1"
|
||||
;;
|
||||
ctera,c200-v2)
|
||||
part=$(find_mtd_part "active_bank")
|
||||
|
||||
if [ -n "$part" ]; then
|
||||
CI_KERNPART="$(strings $part | grep bank)"
|
||||
nand_do_upgrade "$1"
|
||||
else
|
||||
echo "active_bank partition missed!"
|
||||
return 1
|
||||
fi
|
||||
;;
|
||||
cznic,turris-omnia|\
|
||||
kobol,helios4|\
|
||||
solidrun,clearfog-base-a1|\
|
||||
|
||||
@@ -0,0 +1,426 @@
|
||||
// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
|
||||
/*
|
||||
* Device Tree file for Ctera C200-V2
|
||||
*
|
||||
* Copyright (C) 2021 Pawel Dembicki <paweldembicki@gmail.com>
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include "armada-370.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/thermal/thermal.h>
|
||||
#include <dt-bindings/leds/common.h>
|
||||
|
||||
/ {
|
||||
model = "Ctera C200 V2";
|
||||
compatible = "ctera,c200-v2", "marvell,armada370", "marvell,armada-370-xp";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_status_green;
|
||||
led-failsafe = &led_status_red;
|
||||
led-running = &led_status_green;
|
||||
led-upgrade = &led_status_red;
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,115200";
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
memory {
|
||||
device_type = "memory";
|
||||
reg = <0x00000000 0x40000000>; /* 1024 MB */
|
||||
};
|
||||
|
||||
soc {
|
||||
ranges = <MBUS_ID(0xf0, 0x01) 0 0xd0000000 0x100000
|
||||
MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000
|
||||
MBUS_ID(0x09, 0x01) 0 0xf1100000 0x10000>;
|
||||
};
|
||||
|
||||
thermal-zones {
|
||||
ethphy-thermal {
|
||||
polling-delay = <20000>;
|
||||
polling-delay-passive = <2000>;
|
||||
|
||||
thermal-sensors = <ðphy0>;
|
||||
|
||||
trips {
|
||||
ethphy_alert1: trip1 {
|
||||
temperature = <65000>;
|
||||
hysteresis = <4000>;
|
||||
type = "passive";
|
||||
};
|
||||
|
||||
ethphy_crit: trip2 {
|
||||
temperature = <100000>;
|
||||
hysteresis = <2000>;
|
||||
type = "critical";
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
pinctrl-0 = <&pmx_buttons>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
power {
|
||||
label = "Power Button";
|
||||
linux,code = <KEY_POWER>;
|
||||
gpios = <&gpio0 10 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
reset {
|
||||
label = "Reset Button";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
usb1 {
|
||||
label = "USB1 Button";
|
||||
linux,code = <BTN_0>;
|
||||
gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
usb2 {
|
||||
label = "USB2 Button";
|
||||
linux,code = <BTN_1>;
|
||||
gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-poweroff {
|
||||
compatible = "gpio-poweroff";
|
||||
pinctrl-0 = <&pmx_poweroff>;
|
||||
pinctrl-names = "default";
|
||||
gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
pinctrl-0 = <&pmx_leds1 &pmx_leds2>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
led-0 {
|
||||
function = LED_FUNCTION_USB;
|
||||
function-enumerator = <2>;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led-1 {
|
||||
function = LED_FUNCTION_USB;
|
||||
function-enumerator = <2>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "usbport";
|
||||
trigger-sources = <&usb1_port 1>, <&usb2_port 1>;
|
||||
};
|
||||
|
||||
led-2 {
|
||||
function = LED_FUNCTION_USB;
|
||||
function-enumerator = <1>;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led-3 {
|
||||
function = LED_FUNCTION_USB;
|
||||
function-enumerator = <1>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "usbport";
|
||||
trigger-sources = <&usb1_port 2>, <&usb2_port 2>;
|
||||
};
|
||||
|
||||
led-4 {
|
||||
function = LED_FUNCTION_DISK;
|
||||
function-enumerator = <2>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "ata2";
|
||||
};
|
||||
|
||||
led-5 {
|
||||
function = LED_FUNCTION_DISK;
|
||||
function-enumerator = <1>;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
gpios = <&gpio1 18 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led-6 {
|
||||
function = LED_FUNCTION_DISK;
|
||||
function-enumerator = <2>;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led-7 {
|
||||
function = LED_FUNCTION_INDICATOR;
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
gpios = <&gpio1 20 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led-8 {
|
||||
function = LED_FUNCTION_DISK_ERR;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led-9 {
|
||||
function = LED_FUNCTION_DISK_ERR;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
gpios = <&gpio1 23 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_status_red: led-10 {
|
||||
label = "red:status";
|
||||
function = LED_FUNCTION_STATUS;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led-11 {
|
||||
function = LED_FUNCTION_DISK;
|
||||
function-enumerator = <1>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "ata1";
|
||||
};
|
||||
|
||||
led_status_green: led-12 {
|
||||
label = "green:status";
|
||||
function = LED_FUNCTION_STATUS;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
gpios = <&gpio1 26 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&coherencyfab {
|
||||
broken-idle;
|
||||
};
|
||||
|
||||
ð1 {
|
||||
pinctrl-0 = <&ge1_rgmii_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
phy-handle = <ðphy0>;
|
||||
phy-connection-type = "rgmii-id";
|
||||
};
|
||||
|
||||
&i2c0 {
|
||||
pinctrl-0 = <&i2c0_pins>;
|
||||
pinctrl-names = "default";
|
||||
clock-frequency = <100000>;
|
||||
status = "okay";
|
||||
|
||||
hwmon@2a {
|
||||
compatible = "nuvoton,nct7802";
|
||||
reg = <0x2a>;
|
||||
};
|
||||
|
||||
rtc@30 {
|
||||
compatible = "sii,s35390a";
|
||||
reg = <0x30>;
|
||||
};
|
||||
};
|
||||
|
||||
&mdio {
|
||||
pinctrl-0 = <&mdio_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
ethphy0: ethernet-phy@0 { /* Marvell 88E1318 */
|
||||
reg = <0>;
|
||||
#thermal-sensor-cells = <0>;
|
||||
};
|
||||
};
|
||||
|
||||
&nand_controller {
|
||||
status = "okay";
|
||||
|
||||
nand@0 {
|
||||
reg = <0>;
|
||||
label = "pxa3xx_nand-0";
|
||||
nand-rb = <0>;
|
||||
marvell,nand-keep-config;
|
||||
nand-on-flash-bbt;
|
||||
nand-ecc-strength = <4>;
|
||||
nand-ecc-step-size = <512>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "uboot";
|
||||
reg = <0x0000000 0x200000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@200000 {
|
||||
label = "certificate";
|
||||
reg = <0x0200000 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@300000 {
|
||||
label = "preset_cfg";
|
||||
reg = <0x0300000 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@400000 {
|
||||
label = "dev_params";
|
||||
reg = <0x0400000 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
partition@500000 {
|
||||
label = "active_bank";
|
||||
reg = <0x0500000 0x0100000>;
|
||||
};
|
||||
|
||||
partition@600000 {
|
||||
label = "magic";
|
||||
reg = <0x0600000 0x0100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@700000 {
|
||||
label = "bank1";
|
||||
reg = <0x0700000 0x2800000>;
|
||||
};
|
||||
|
||||
partition@2f00000 {
|
||||
label = "bank2";
|
||||
reg = <0x2f00000 0x2800000>;
|
||||
};
|
||||
|
||||
/* 0x5700000-0x5a00000 undefined in vendor firmware */
|
||||
|
||||
partition@5a00000 {
|
||||
label = "reserved";
|
||||
reg = <0x5a00000 0x2000000>;
|
||||
};
|
||||
|
||||
partition@7a00000 {
|
||||
label = "ubi";
|
||||
reg = <0x7a00000 0x8600000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pciec {
|
||||
status = "okay";
|
||||
|
||||
pcie@1,0 {
|
||||
pinctrl-0 = <&pmx_pcie>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
|
||||
|
||||
/* -[0000:00]---01.0-[01]----00.0 */
|
||||
/* usbport trigger won't work */
|
||||
bridge@0,1 {
|
||||
compatible = "pci11ab,6710";
|
||||
reg = <0x3800 0 0 0 0>;
|
||||
#address-cells = <3>;
|
||||
#size-cells = <2>;
|
||||
|
||||
usb@1,0 {
|
||||
/* Renesas uPD720202 */
|
||||
compatible = "pci1912,0015";
|
||||
reg = <0x1000 0 0 0 0>;
|
||||
#address-cells = <3>;
|
||||
#size-cells = <2>;
|
||||
|
||||
usb1_port: port@1 {
|
||||
reg = <1>;
|
||||
#trigger-source-cells = <1>;
|
||||
};
|
||||
|
||||
usb2_port: port@2 {
|
||||
reg = <2>;
|
||||
#trigger-source-cells = <1>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pinctrl {
|
||||
pmx_poweroff: pmx-poweroff {
|
||||
marvell,pins = "mpp7";
|
||||
marvell,function = "gpo";
|
||||
};
|
||||
|
||||
pmx_power_cpu: pmx-power-cpu {
|
||||
marvell,pins = "mpp4";
|
||||
marvell,function = "vdd";
|
||||
};
|
||||
|
||||
pmx_buttons: pmx-buttons {
|
||||
marvell,pins = "mpp6", "mpp10", "mpp14", "mpp32";
|
||||
marvell,function = "gpio";
|
||||
};
|
||||
|
||||
pmx_leds1: pmx-leds1 {
|
||||
marvell,pins = "mpp47";
|
||||
marvell,function = "gpo";
|
||||
};
|
||||
|
||||
pmx_leds2: pmx-leds2 {
|
||||
marvell,pins = "mpp12", "mpp13", "mpp15", "mpp16", "mpp50", "mpp51",
|
||||
"mpp52", "mpp53", "mpp55", "mpp56", "mpp57", "mpp58";
|
||||
marvell,function = "gpio";
|
||||
};
|
||||
|
||||
pmx_pcie: pmx-pcie {
|
||||
marvell,pins = "mpp59";
|
||||
marvell,function = "gpio";
|
||||
};
|
||||
|
||||
/* this gpio is connected to the pin of buzzer
|
||||
* leave it as is due lack of proper driver
|
||||
*/
|
||||
pmx_buzzer: pmx-buzzer {
|
||||
marvell,pins = "mpp63";
|
||||
marvell,function = "gpio";
|
||||
};
|
||||
};
|
||||
|
||||
&pmsu {
|
||||
pinctrl-0 = <&pmx_power_cpu>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
&rtc {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&sata {
|
||||
nr-ports = <2>;
|
||||
status = "okay";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
hdd0_temp: sata-port@0 {
|
||||
reg = <0>;
|
||||
#thermal-sensor-cells = <0>;
|
||||
};
|
||||
|
||||
hdd1_temp: sata-port@1 {
|
||||
reg = <1>;
|
||||
#thermal-sensor-cells = <0>;
|
||||
};
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
status = "okay";
|
||||
};
|
||||
@@ -51,6 +51,63 @@ define Build/buffalo-kernel-jffs2
|
||||
rm -rf $(KDIR)/kernel_jffs2 $@.fakerd
|
||||
endef
|
||||
|
||||
# Some info about Ctera firmware:
|
||||
# 1. It's simple tar file (GNU standard), but it must have ".firm" suffix.
|
||||
# 2. It contains two images: kernel and romdisk. Both are required.
|
||||
# 3. Every image has header and trailer file.
|
||||
# 4. The struct of tar firmware is: header kernel trailer header romdisk trailer
|
||||
# 5. In header file are some strings used to describe image. It was decoded from
|
||||
# factory image.
|
||||
# 6. Version format in header file is restricted by Original FW.
|
||||
# 7. Trailer file contains MD5 sum string of header and image file.
|
||||
# 8. Firmware file must have <=24MB size.
|
||||
|
||||
define Build/ctera-firmware
|
||||
mkdir -p $@.tmp
|
||||
|
||||
# Prepare header and trailer file for kernel
|
||||
echo "# CTera firmware information file" > $@.tmp/header
|
||||
echo "image_type=kernel" >> $@.tmp/header
|
||||
echo "arch=ARM" >> $@.tmp/header
|
||||
echo "board=2Drive_A" >> $@.tmp/header
|
||||
echo "version=5.5.165.61499" >> $@.tmp/header
|
||||
echo "kernel_cmd=console=ttyS0,115200 earlycon" >> $@.tmp/header
|
||||
echo "date=$$(date $(if $(SOURCE_DATE_EPOCH),-d@$(SOURCE_DATE_EPOCH)))" \
|
||||
>> $@.tmp/header
|
||||
|
||||
cp $@ $@.tmp/kernel
|
||||
|
||||
echo "MD5=$$(cat $@.tmp/header $@.tmp/kernel | $(MKHASH) md5)" \
|
||||
> $@.tmp/trailer
|
||||
|
||||
tar $(if $(SOURCE_DATE_EPOCH),--mtime="@$(SOURCE_DATE_EPOCH)") \
|
||||
-H gnu -C $@.tmp -cf $@.tar header kernel trailer
|
||||
|
||||
# Prepare header and trailer file for fake romdisk
|
||||
echo "# CTera firmware information file" > $@.tmp/header
|
||||
echo "image_type=romdisk" >> $@.tmp/header
|
||||
echo "initrd=yes" >> $@.tmp/header
|
||||
echo "arch=ARM" >> $@.tmp/header
|
||||
echo "board=2Drive_A" >> $@.tmp/header
|
||||
echo "version=5.5.165.61499" >> $@.tmp/header
|
||||
echo "date=$$(date $(if $(SOURCE_DATE_EPOCH),-d@$(SOURCE_DATE_EPOCH)))" \
|
||||
>> $@.tmp/header
|
||||
|
||||
rm -f $@
|
||||
touch $@
|
||||
$(call Build/append-uImage-fakehdr, ramdisk)
|
||||
cp $@ $@.tmp/romdisk
|
||||
|
||||
echo "MD5=$$(cat $@.tmp/header $@.tmp/romdisk | $(MKHASH) md5)" \
|
||||
> $@.tmp/trailer
|
||||
|
||||
tar $(if $(SOURCE_DATE_EPOCH),--mtime="@$(SOURCE_DATE_EPOCH)") \
|
||||
-H gnu -C $@.tmp -rf $@.tar header romdisk trailer
|
||||
|
||||
mv $@.tar $@
|
||||
rm -rf $@.tmp
|
||||
endef
|
||||
|
||||
define Build/sdcard-img
|
||||
SIGNATURE="$(IMG_PART_SIGNATURE)" \
|
||||
./gen_mvebu_sdcard_img.sh $@ \
|
||||
|
||||
@@ -31,6 +31,24 @@ define Device/buffalo_ls421de
|
||||
endef
|
||||
TARGET_DEVICES += buffalo_ls421de
|
||||
|
||||
define Device/ctera_c200-v2
|
||||
PAGESIZE := 2048
|
||||
SUBPAGESIZE := 512
|
||||
BLOCKSIZE := 128k
|
||||
DEVICE_VENDOR := Ctera
|
||||
DEVICE_MODEL := C200
|
||||
DEVICE_VARIANT := V2
|
||||
SOC := armada-370
|
||||
KERNEL := kernel-bin | append-dtb | uImage none | ctera-firmware
|
||||
KERNEL_IN_UBI :=
|
||||
KERNEL_SUFFIX := -factory.firm
|
||||
DEVICE_PACKAGES := \
|
||||
kmod-gpio-button-hotplug kmod-hwmon-drivetemp kmod-hwmon-nct7802 \
|
||||
kmod-rtc-s35390a kmod-usb3 kmod-usb-ledtrig-usbport
|
||||
IMAGES := sysupgrade.bin
|
||||
endef
|
||||
TARGET_DEVICES += ctera_c200-v2
|
||||
|
||||
define Device/cznic_turris-omnia
|
||||
DEVICE_VENDOR := CZ.NIC
|
||||
DEVICE_MODEL := Turris Omnia
|
||||
|
||||
Reference in New Issue
Block a user