ath79: add support for TP-Link CPE710-v1

TP-Link CPE710-v1 is an outdoor wireless CPE for 5 GHz with one Ethernet port based on the AP152 reference board Specifications: - SoC: QCA9563-AL3A MIPS 74kc @ 775MHz, AHB @ 258MHz - RAM: 128MiB DDR2 @ 650MHz - Flash: 16MiB SPI NOR Based on the GD25Q128 - Wi-Fi 5Ghz: ath10k chip (802.11ac for up to 867Mbps on 5GHz wireless data rate) Based on the QCA9896 - Ethernet: one 1GbE port - 23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal reflector - Power, LAN, WLAN5G Blue LEDs - 3x Blue LEDs Flashing instructions: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 30-40 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP address:192.168.0.254 Signed-off-by: Andrew Cameron <apcameron@softhome.net> [convert to nvmem, fix MAC assignment in 11-ath10k-caldata] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-04-12 13:24:33 -05:00
parent 3c3b84fd87
commit ac03e24635
6 changed files with 209 additions and 1 deletions
--- a/target/linux/ath79/dts/qca9563_tplink_cpe710-v1.dts
+++ b/target/linux/ath79/dts/qca9563_tplink_cpe710-v1.dts
@@ -0,0 +1,152 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca956x.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "TP-Link CPE710 v1";
+	compatible = "tplink,cpe710-v1", "qca,qca9563";
+
+	aliases {
+		label-mac-device = &eth0;
+		led-boot = &led_lan;
+		led-failsafe = &led_lan;
+		led-upgrade = &led_lan;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_lan: lan {
+			label = "blue:lan";
+			gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
+		};
+
+		wlan5g {
+			label = "blue:wlan5g";
+			gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy0tpt";
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "Reset button";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+			debounce-interval = <60>;
+		};
+	};
+};
+
+&pcie {
+	status = "okay";
+};
+
+&spi {
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <40000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "u-boot";
+				reg = <0x000000 0x040000>;
+				read-only;
+			};
+
+			partition@40000 {
+				label = "u-boot-env";
+				reg = <0x040000 0x010000>;
+			};
+
+			partition@50000 {
+				label = "partition-table";
+				reg = <0x050000 0x010000>;
+				read-only;
+			};
+
+			info: partition@60000 {
+				label = "info";
+				reg = <0x060000 0x010000>;
+				read-only;
+			};
+
+			partition@70000 {
+				compatible = "denx,uimage";
+				label = "firmware";
+				reg = <0x070000 0xf50000>;
+			};
+
+			partition@fc0000 {
+				label = "config";
+				reg = <0xfc0000 0x030000>;
+				read-only;
+			};
+
+			art: partition@ff0000 {
+				label = "art";
+				reg = <0xff0000 0x010000>;
+				read-only;
+			};
+		};
+	};
+};
+
+&pinmux {
+	mdio_pins: mdio_pins {
+		/* GPIO 10 as MDIO(0x20), GPIO 8 as MDC(0x21) */
+		pinctrl-single,bits = <0x8 0x00200021 0x00ff00ff>;
+	};
+};
+
+&mdio0 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&mdio_pins>;
+
+	phy-mask = <0x10>;
+
+	phy4: ethernet-phy@4 {
+		reg = <4>;
+		reset-gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+
+	phy-handle = <&phy4>;
+	phy-mode = "sgmii";
+
+	nvmem-cells = <&macaddr_info_8>;
+	nvmem-cell-names = "mac-address";
+
+	qca956x-serdes-fixup;
+
+	gmac-config {
+		device = <&gmac>;
+	};
+};
+
+&info {
+	compatible = "nvmem-cells";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	macaddr_info_8: macaddr@8 {
+		reg = <0x8 0x6>;
+	};
+};