ath79: add support for TP-Link CPE710-v1
TP-Link CPE710-v1 is an outdoor wireless CPE for 5 GHz with one Ethernet port based on the AP152 reference board Specifications: - SoC: QCA9563-AL3A MIPS 74kc @ 775MHz, AHB @ 258MHz - RAM: 128MiB DDR2 @ 650MHz - Flash: 16MiB SPI NOR Based on the GD25Q128 - Wi-Fi 5Ghz: ath10k chip (802.11ac for up to 867Mbps on 5GHz wireless data rate) Based on the QCA9896 - Ethernet: one 1GbE port - 23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal reflector - Power, LAN, WLAN5G Blue LEDs - 3x Blue LEDs Flashing instructions: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 30-40 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP address:192.168.0.254 Signed-off-by: Andrew Cameron <apcameron@softhome.net> [convert to nvmem, fix MAC assignment in 11-ath10k-caldata] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit is contained in:
Andrew Cameron
committed by
Adrian Schmutzler
Adrian Schmutzler
parent
3c3b84fd87
commit
ac03e24635
152
target/linux/ath79/dts/qca9563_tplink_cpe710-v1.dts
Normal file
152
target/linux/ath79/dts/qca9563_tplink_cpe710-v1.dts
Normal file
@@ -0,0 +1,152 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qca956x.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
model = "TP-Link CPE710 v1";
|
||||
compatible = "tplink,cpe710-v1", "qca,qca9563";
|
||||
|
||||
aliases {
|
||||
label-mac-device = ð0;
|
||||
led-boot = &led_lan;
|
||||
led-failsafe = &led_lan;
|
||||
led-upgrade = &led_lan;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_lan: lan {
|
||||
label = "blue:lan";
|
||||
gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wlan5g {
|
||||
label = "blue:wlan5g";
|
||||
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "Reset button";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&spi {
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <40000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x000000 0x040000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x040000 0x010000>;
|
||||
};
|
||||
|
||||
partition@50000 {
|
||||
label = "partition-table";
|
||||
reg = <0x050000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
info: partition@60000 {
|
||||
label = "info";
|
||||
reg = <0x060000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@70000 {
|
||||
compatible = "denx,uimage";
|
||||
label = "firmware";
|
||||
reg = <0x070000 0xf50000>;
|
||||
};
|
||||
|
||||
partition@fc0000 {
|
||||
label = "config";
|
||||
reg = <0xfc0000 0x030000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
art: partition@ff0000 {
|
||||
label = "art";
|
||||
reg = <0xff0000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pinmux {
|
||||
mdio_pins: mdio_pins {
|
||||
/* GPIO 10 as MDIO(0x20), GPIO 8 as MDC(0x21) */
|
||||
pinctrl-single,bits = <0x8 0x00200021 0x00ff00ff>;
|
||||
};
|
||||
};
|
||||
|
||||
&mdio0 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&mdio_pins>;
|
||||
|
||||
phy-mask = <0x10>;
|
||||
|
||||
phy4: ethernet-phy@4 {
|
||||
reg = <4>;
|
||||
reset-gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
|
||||
phy-handle = <&phy4>;
|
||||
phy-mode = "sgmii";
|
||||
|
||||
nvmem-cells = <&macaddr_info_8>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
|
||||
qca956x-serdes-fixup;
|
||||
|
||||
gmac-config {
|
||||
device = <&gmac>;
|
||||
};
|
||||
};
|
||||
|
||||
&info {
|
||||
compatible = "nvmem-cells";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
macaddr_info_8: macaddr@8 {
|
||||
reg = <0x8 0x6>;
|
||||
};
|
||||
};
|
||||
@@ -169,7 +169,8 @@ enterasys,ws-ap3705i|\
|
||||
openmesh,mr900-v1|\
|
||||
openmesh,mr900-v2|\
|
||||
openmesh,mr1750-v1|\
|
||||
openmesh,mr1750-v2)
|
||||
openmesh,mr1750-v2|\
|
||||
tplink,cpe710-v1)
|
||||
ucidef_set_led_netdev "lan" "LAN" "blue:lan" "eth0"
|
||||
;;
|
||||
compex,wpj344-16m|\
|
||||
|
||||
@@ -63,6 +63,7 @@ ath79_setup_interfaces()
|
||||
tplink,cpe510-v3|\
|
||||
tplink,cpe610-v1|\
|
||||
tplink,cpe610-v2|\
|
||||
tplink,cpe710-v1|\
|
||||
tplink,eap225-outdoor-v1|\
|
||||
tplink,eap225-v3|\
|
||||
tplink,eap245-v1|\
|
||||
|
||||
@@ -236,6 +236,12 @@ case "$FIRMWARE" in
|
||||
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
|
||||
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
|
||||
;;
|
||||
tplink,cpe710-v1)
|
||||
caldata_extract "art" 0x5000 0x2f20
|
||||
ath10k_patch_mac $(mtd_get_mac_binary info 0x8)
|
||||
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
|
||||
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
|
||||
;;
|
||||
tplink,eap225-outdoor-v1|\
|
||||
tplink,eap225-v3|\
|
||||
tplink,eap225-wall-v2|\
|
||||
|
||||
@@ -362,6 +362,17 @@ define Device/tplink_cpe610-v2
|
||||
endef
|
||||
TARGET_DEVICES += tplink_cpe610-v2
|
||||
|
||||
define Device/tplink_cpe710-v1
|
||||
$(Device/tplink-safeloader-uimage)
|
||||
SOC := qca9563
|
||||
IMAGE_SIZE := 15680k
|
||||
DEVICE_MODEL := CPE710
|
||||
DEVICE_VARIANT := v1
|
||||
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
|
||||
TPLINK_BOARD_ID := CPE710V1
|
||||
endef
|
||||
TARGET_DEVICES += tplink_cpe710-v1
|
||||
|
||||
define Device/tplink-eap2x5
|
||||
$(Device/tplink-safeloader)
|
||||
LOADER_TYPE := elf
|
||||
|
||||
@@ -534,6 +534,43 @@ static struct device_info boards[] = {
|
||||
.first_sysupgrade_partition = "os-image",
|
||||
.last_sysupgrade_partition = "support-list",
|
||||
},
|
||||
/** Firmware layout for the CPE710 V1 */
|
||||
{
|
||||
.id = "CPE710V1",
|
||||
.vendor = "CPE710(TP-LINK|UN|AC866-5|00000000):1.0\r\n",
|
||||
.support_list =
|
||||
"SupportList:\r\n"
|
||||
"CPE710(TP-LINK|UN|AC866-5|00000000):1.0\r\n"
|
||||
"CPE710(TP-LINK|EU|AC866-5|45550000):1.0\r\n"
|
||||
"CPE710(TP-LINK|US|AC866-5|55530000):1.0\r\n"
|
||||
"CPE710(TP-LINK|UN|AC866-5):1.0\r\n"
|
||||
"CPE710(TP-LINK|EU|AC866-5):1.0\r\n"
|
||||
"CPE710(TP-LINK|US|AC866-5):1.0\r\n",
|
||||
.part_trail = 0xff,
|
||||
.soft_ver = SOFT_VER_DEFAULT,
|
||||
|
||||
.partitions = {
|
||||
{"fs-uboot", 0x00000, 0x50000},
|
||||
{"partition-table", 0x50000, 0x02000},
|
||||
{"default-mac", 0x60000, 0x00020},
|
||||
{"serial-number", 0x60100, 0x00020},
|
||||
{"product-info", 0x61100, 0x00100},
|
||||
{"device-info", 0x61400, 0x00400},
|
||||
{"signature", 0x62000, 0x00400},
|
||||
{"device-id", 0x63000, 0x00100},
|
||||
{"firmware", 0x70000, 0xf40000},
|
||||
{"soft-version", 0xfb0000, 0x00100},
|
||||
{"support-list", 0xfb1000, 0x01000},
|
||||
{"user-config", 0xfc0000, 0x10000},
|
||||
{"default-config", 0xfd0000, 0x10000},
|
||||
{"log", 0xfe0000, 0x10000},
|
||||
{"radio", 0xff0000, 0x10000},
|
||||
{NULL, 0, 0}
|
||||
},
|
||||
|
||||
.first_sysupgrade_partition = "os-image",
|
||||
.last_sysupgrade_partition = "support-list",
|
||||
},
|
||||
|
||||
{
|
||||
.id = "WBS210",
|
||||
|
||||
Reference in New Issue
Block a user