ath79: add support for COMFAST CF-E560AC

This commit adds support for the COMFAST CF-E560AC, an ap143 based
in-wall access point.

Specifications:
 - SoC: Qualcomm Atheros QCA9531
 - RAM: 128 MB DDR2 (Winbond W971GG6SB-25)
 - Storage: 16 MB NOR (Winbond 25Q128JVSO)
 - WAN: 1x 10/100 PoE ethernet (48v)
 - LAN: 4x 10/100 ethernet
 - WLAN1: QCA9531 - 802.11b/g/n - 2x SKY85303-21 FEM
 - WLAN2: QCA9886 - 802.11ac/n/a - 2x SKY85735-11 FEM
 - USB: one external USB2.0 port
 - UART: 3.3v, 2.54mm headers already populated on board
 - LED: 7x external
 - Button: 1x external
 - Boot: U-Boot 1.1.4 (pepe2k/u-boot_mod)

MAC addressing:

- stock
  LAN    *:40 (label)
  WAN    *:41
  5G     *:42
  2.4G   *:4a

- flash (art partition)
  0x0    *:40 (label)
  0x6    *:42
  0x1002 *:41
  0x5006 *:43

This device contains valid MAC addresses in art 0x0, 0x6, 0x1002 and
0x5006, however the vendor firmware only reads from art:0x0 for the LAN
interface and then increments in 02_network. They also jump 8 addresses
for the second wifi interface (2.4 GHz). This behavior has been duplicated
in the DTS and ath10k hotplug to align addresses with the vendor firmware
v2.6.0.

Recovery instructions:

This device contains built-in u-boot tftp recovery.

1. Configure PC with static IP 192.168.1.10/24 and tftp server.
2. Place desired image at /firmware_auto.bin at tftp root.
3. Connect device to PC, and power on.
4. Device will fetch flash from tftp, flash and reboot into new image.

Signed-off-by: August Huber <auh@google.com>
[move jtag_disable_pins, remove unnecessary statuses in DTS, remove
duplicate entry in 11-ath10k-caldata, remove hub_port0 label in DTS]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

target/linux/ath79/generic/base-files/etc/board.d/01_leds

@@ -73,6 +73,13 @@ comfast,cf-e5)
 	ucidef_set_led_rssi "rssimedium" "RSSIMEDIUM" "$boardname:blue:rssi1" "wlan0" "33" "100"
 	ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "$boardname:blue:rssi2" "wlan0" "66" "100"
 	;;
+comfast,cf-e560ac)
+	ucidef_set_led_netdev "wan" "WAN" "$boardname:blue:wan" "eth1"
+	ucidef_set_led_switch "lan1" "LAN1" "$boardname:blue:lan1" "switch0" "0x02"
+	ucidef_set_led_switch "lan2" "LAN2" "$boardname:blue:lan2" "switch0" "0x04"
+	ucidef_set_led_switch "lan3" "LAN3" "$boardname:blue:lan3" "switch0" "0x08"
+	ucidef_set_led_switch "lan4" "LAN4" "$boardname:blue:lan4" "switch0" "0x10"
+	;;
 dlink,dir-842-c1|\
 dlink,dir-842-c2|\
 dlink,dir-842-c3|\

target/linux/ath79/generic/base-files/etc/board.d/02_network

@@ -103,6 +103,13 @@ ath79_setup_interfaces()
 	ubnt,routerstation)
 		ucidef_set_interfaces_lan_wan "eth1" "eth0"
 		;;
+	comfast,cf-e560ac|\
+	tplink,archer-c60-v1|\
+	tplink,archer-c60-v2)
+		ucidef_set_interface_wan "eth1"
+		ucidef_add_switch "switch0" \
+			"0@eth0" "1:lan" "2:lan" "3:lan" "4:lan"
+		;;
 	comfast,cf-wr650ac-v1|\
 	comfast,cf-wr650ac-v2)
 		ucidef_add_switch "switch0" \
@@ -228,12 +235,6 @@ ath79_setup_interfaces()
 		ucidef_add_switch "switch0" \
 			"0@eth1" "2:lan" "3:lan" "4:lan" "5:lan" "6@eth0" "1:wan"
 		;;
-	tplink,archer-c60-v1|\
-	tplink,archer-c60-v2)
-		ucidef_set_interface_wan "eth1"
-		ucidef_add_switch "switch0" \
-			"0@eth0" "1:lan" "2:lan" "3:lan" "4:lan"
-		;;
 	tplink,archer-d50-v1)
 		ucidef_add_switch "switch0" \
 			"0@eth0" "2:lan:3" "3:lan:2" "4:lan:1" "1:wan"

target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata

@@ -130,6 +130,13 @@ case "$FIRMWARE" in
 			/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
 		rm /lib/firmware/ath10k/QCA9888/hw2.0/board-2.bin
 		;;
+	comfast,cf-e560ac)
+		caldata_extract "art" 0x5000 0x2f20
+		ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary art 0x0) +2)
+		ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
+			/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
+		rm /lib/firmware/ath10k/QCA9888/hw2.0/board-2.bin
+		;;
 	dlink,dir-842-c1|\
 	dlink,dir-842-c2|\
 	dlink,dir-842-c3|\