ath79: Add support for OpenMesh OM2P v4
Device specifications:
======================
* Qualcomm/Atheros QCA9533 v2
* 650/600/217 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 1T1R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
- eth0
+ Label: Ethernet 1
+ 24V passive POE (mode B)
- eth1
+ Label: Ethernet 2
+ 802.3af POE
+ builtin switch port 1
* 12-24V 1A DC
* external antenna
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to
the device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[wrap two very long lines, fix typo in comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit is contained in:
Sven Eckelmann
committed by
Adrian Schmutzler
Adrian Schmutzler
parent
e1938d3397
commit
dd1d95cb03
112
target/linux/ath79/generic/base-files/lib/upgrade/openmesh.sh
Normal file
112
target/linux/ath79/generic/base-files/lib/upgrade/openmesh.sh
Normal file
@@ -0,0 +1,112 @@
|
||||
# The U-Boot loader of the OpenMesh devices requires image sizes and
|
||||
# checksums to be provided in the U-Boot environment.
|
||||
# The OpenMesh devices come with 2 main partitions - while one is active
|
||||
# sysupgrade will flash the other. The boot order is changed to boot the
|
||||
# newly flashed partition. If the new partition can't be booted due to
|
||||
# upgrade failures the previously used partition is loaded.
|
||||
|
||||
cfg_value_get()
|
||||
{
|
||||
local cfg=$1 cfg_opt
|
||||
local section=$2 our_section=0
|
||||
local param=$3 our_param=
|
||||
|
||||
for cfg_opt in $cfg; do
|
||||
[ "$cfg_opt" = "[$section]" ] && our_section=1 && continue
|
||||
[ "$our_section" = "1" ] || continue
|
||||
|
||||
our_param=${cfg_opt%%=*}
|
||||
[ "$param" = "$our_param" ] && echo ${cfg_opt##*=} && break
|
||||
done
|
||||
}
|
||||
|
||||
platform_do_upgrade_openmesh()
|
||||
{
|
||||
local img_path="$1"
|
||||
local restore_backup
|
||||
|
||||
local setenv_script="/tmp/fw_env_upgrade"
|
||||
|
||||
local inactive_mtd="$(find_mtd_index $PART_NAME)"
|
||||
local inactive_offset="$(cat /sys/class/mtd/mtd${inactive_mtd}/offset)"
|
||||
local total_size="$(cat /sys/class/mtd/mtd${inactive_mtd}/size)"
|
||||
local flash_start_mem=0x9f000000
|
||||
local data_offset=$((64 * 1024))
|
||||
|
||||
# detect to which flash region the new image is written to.
|
||||
#
|
||||
# 1. check what is the mtd index for the first flash region on this
|
||||
# device
|
||||
# 2. check if the target partition ("inactive") has the mtd index of
|
||||
# the first flash region
|
||||
#
|
||||
# - when it is: the new bootseq will be 1,2 and the first region is
|
||||
# modified
|
||||
# - when it isn't: bootseq will be 2,1 and the second region is
|
||||
# modified
|
||||
#
|
||||
# The detection has to be done via the hardcoded mtd partition because
|
||||
# the current boot might be done with the fallback region. Let us
|
||||
# assume that the current bootseq is 1,2. The bootloader detected that
|
||||
# the image in flash region 1 is corrupt and thus switches to flash
|
||||
# region 2. The bootseq in the u-boot-env is now still the same and
|
||||
# the sysupgrade code can now only rely on the actual mtd indexes and
|
||||
# not the bootseq variable to detect the currently booted flash
|
||||
# region/image.
|
||||
#
|
||||
# In the above example, an implementation which uses bootseq ("1,2") to
|
||||
# detect the currently booted image would assume that region 1 is booted
|
||||
# and then overwrite the variables for the wrong flash region (aka the
|
||||
# one which isn't modified). This could result in a device which doesn't
|
||||
# boot anymore to Linux until it was reflashed with ap51-flash.
|
||||
local next_boot_part="1"
|
||||
local primary_kernel_mtd="3"
|
||||
[ "$inactive_mtd" = "$primary_kernel_mtd" ] || next_boot_part="2"
|
||||
|
||||
local cfg_size=$(dd if="$img_path" bs=2 skip=35 count=4 2>/dev/null)
|
||||
local cfg_length=$((0x$cfg_size))
|
||||
local cfg_content=$(dd if="$img_path" bs=1 skip=$data_offset count=$cfg_length 2>/dev/null)
|
||||
|
||||
local kernel_size=$(dd if="$img_path" bs=2 skip=71 count=4 2>/dev/null)
|
||||
local kernel_length=$((0x$kernel_size))
|
||||
local kernel_md5=$(cfg_value_get "$cfg_content" "vmlinux" "md5sum")
|
||||
|
||||
local rootfs_size=$(dd if="$img_path" bs=2 skip=107 count=4 2>/dev/null)
|
||||
local rootfs_length=$((0x$rootfs_size))
|
||||
local rootfs_md5=$(cfg_value_get "$cfg_content" "rootfs" "md5sum")
|
||||
local rootfs_checksize=$(cfg_value_get "$cfg_content" "rootfs" "checksize")
|
||||
|
||||
# take care of restoring a saved config
|
||||
[ -n "$UPGRADE_BACKUP" ] && restore_backup="${MTD_CONFIG_ARGS} -j ${UPGRADE_BACKUP}"
|
||||
|
||||
# write image parts
|
||||
mtd -q erase inactive
|
||||
dd if="$img_path" bs=1 skip=$((data_offset + cfg_length + kernel_length)) count=$rootfs_length 2>&- | \
|
||||
mtd -n -p $kernel_length $restore_backup write - $PART_NAME
|
||||
dd if="$img_path" bs=1 skip=$((data_offset + cfg_length)) count=$kernel_length 2>&- | \
|
||||
mtd -n write - $PART_NAME
|
||||
|
||||
# prepare new u-boot env
|
||||
if [ "$next_boot_part" = "1" ]; then
|
||||
echo "bootseq 1,2" > $setenv_script
|
||||
else
|
||||
echo "bootseq 2,1" > $setenv_script
|
||||
fi
|
||||
|
||||
printf "kernel_size_%i %i\n" $next_boot_part $((kernel_length / 1024)) >> $setenv_script
|
||||
printf "vmlinux_start_addr 0x%08x\n" $((flash_start_mem + inactive_offset)) >> $setenv_script
|
||||
printf "vmlinux_size 0x%08x\n" ${kernel_length} >> $setenv_script
|
||||
printf "vmlinux_checksum %s\n" ${kernel_md5} >> $setenv_script
|
||||
|
||||
printf "rootfs_size_%i %i\n" $next_boot_part $(((total_size-kernel_length) / 1024)) >> $setenv_script
|
||||
printf "rootfs_start_addr 0x%08x\n" $((flash_start_mem+inactive_offset+kernel_length)) >> $setenv_script
|
||||
printf "rootfs_size %s\n" $rootfs_checksize >> $setenv_script
|
||||
printf "rootfs_checksum %s\n" ${rootfs_md5} >> $setenv_script
|
||||
|
||||
# store u-boot env changes
|
||||
mkdir -p /var/lock
|
||||
fw_setenv -s $setenv_script || {
|
||||
echo "failed to update U-Boot environment"
|
||||
return 1
|
||||
}
|
||||
}
|
||||
@@ -50,6 +50,10 @@ platform_do_upgrade() {
|
||||
jjplus,ja76pf2)
|
||||
redboot_fis_do_upgrade "$1" linux
|
||||
;;
|
||||
openmesh,om2p-v4)
|
||||
PART_NAME="inactive"
|
||||
platform_do_upgrade_openmesh "$1"
|
||||
;;
|
||||
plasmacloud,pa300|\
|
||||
plasmacloud,pa300e)
|
||||
PART_NAME="inactive"
|
||||
|
||||
Reference in New Issue
Block a user