ramips: add support for TP-Link RE350
The TP-Link RE350 is a wall-wart AC1200 range extender/access point with a single gigabit ethernet port and two non-detachable antennas, based on the MT7621A SoC with MT7603E and MT7612E radios. Firmware wise it is very similar to the QCA based RE450. SoC: MediaTek MT7621A (880MHz) Flash: 8MiB (Winbond W25Q64) RAM: 64MiB (DDR2) Ethernet: 1x 1Gbit Wireless: 2T2R 2.4Ghz (MT7603E) and 5GHz (MT7612E) LEDs: Power, 2.4G, 5G (blue), WPS (red and blue), ethernet link/act (green) Buttons: On/off, LED, reset, WPS Serial header at J1, 57600 8n1: Pin 1 TX Pin 2 RX Pin 3 GND Pin 4 3.3V Factory image can be uploaded directly through the stock UI. Signed-off-by: Alex Maclean <monkeh@monkeh.net>
This commit is contained in:
Alex Maclean
committed by
Mathias Kresin
Mathias Kresin
parent
1c7144f078
commit
f683385e73
@@ -308,6 +308,12 @@ r6220)
|
||||
set_wifi_led "$board:green:wifi"
|
||||
set_usb_led "$board:green:usb"
|
||||
;;
|
||||
re350-v1)
|
||||
ucidef_set_led_netdev "wifi2g" "Wifi 2.4G" "$board:blue:wifi2G" "wlan0"
|
||||
ucidef_set_led_netdev "wifi5g" "Wifi 5G" "$board:blue:wifi5G" "wlan1"
|
||||
ucidef_set_led_netdev "eth_act" "LAN act" "$board:green:eth_act" "eth0" "tx rx"
|
||||
ucidef_set_led_switch "eth_link" "LAN link" "$board:green:eth_link" "switch0" "0x01"
|
||||
;;
|
||||
re6500)
|
||||
ucidef_set_led_default "power" "power" "$board:white:power" "1"
|
||||
ucidef_set_led_default "wifi" "wifi" "$board:orange:wifi" "1"
|
||||
|
||||
@@ -270,6 +270,10 @@ ramips_setup_interfaces()
|
||||
ucidef_add_switch "switch0" \
|
||||
"1:lan:2" "2:lan:1" "4:wan" "6@eth0"
|
||||
;;
|
||||
re350-v1)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0:lan" "6@eth0"
|
||||
;;
|
||||
re6500)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0:lan:1" "1:lan:2" "2:lan:3" "3:lan:4" "6@eth0"
|
||||
|
||||
@@ -119,6 +119,7 @@ get_status_led() {
|
||||
dap-1350|\
|
||||
na930|\
|
||||
pbr-m1|\
|
||||
re350-v1|\
|
||||
rt-ac51u|\
|
||||
rt-n13u|\
|
||||
rt-n14u|\
|
||||
|
||||
@@ -427,6 +427,9 @@ ramips_board_detect() {
|
||||
*"RB750Gr3")
|
||||
name="rb750gr3"
|
||||
;;
|
||||
*"RE350 v1")
|
||||
name="re350-v1"
|
||||
;;
|
||||
*"RE6500")
|
||||
name="re6500"
|
||||
;;
|
||||
|
||||
@@ -253,6 +253,13 @@ platform_check_image() {
|
||||
# these boards use metadata images
|
||||
return 0
|
||||
;;
|
||||
re350-v1)
|
||||
[ "$magic" != "01000000" ] && {
|
||||
echo "Invalid image type."
|
||||
return 1
|
||||
}
|
||||
return 0
|
||||
;;
|
||||
ubnt-erx|\
|
||||
ubnt-erx-sfp)
|
||||
nand_do_platform_check "$board" "$1"
|
||||
|
||||
164
target/linux/ramips/dts/RE350.dts
Normal file
164
target/linux/ramips/dts/RE350.dts
Normal file
@@ -0,0 +1,164 @@
|
||||
/dts-v1/;
|
||||
|
||||
#include "mt7621.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
compatible = "tplink,re350-v1", "mediatek,mt7621-soc";
|
||||
model = "TP-LINK RE350 v1";
|
||||
|
||||
memory@0 {
|
||||
device_type = "memory";
|
||||
reg = <0x0 0x4000000>;
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,57600";
|
||||
};
|
||||
|
||||
gpio-leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
power {
|
||||
label = "re350-v1:blue:power";
|
||||
gpios = <&gpio0 22 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wifi2g {
|
||||
label = "re350-v1:blue:wifi2G";
|
||||
gpios = <&gpio0 23 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wifi5g {
|
||||
label = "re350-v1:blue:wifi5G";
|
||||
gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wps_r {
|
||||
label = "re350-v1:red:wps";
|
||||
gpios = <&gpio0 25 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
wps_b {
|
||||
label = "re350-v1:blue:wps";
|
||||
gpios = <&gpio0 26 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
eth {
|
||||
label = "re350-v1:green:eth_act";
|
||||
gpios = <&gpio0 28 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
eth2 {
|
||||
label = "re350-v1:green:eth_link";
|
||||
gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-keys-polled {
|
||||
compatible = "gpio-keys-polled";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
poll-interval = <20>;
|
||||
|
||||
led {
|
||||
label = "led";
|
||||
gpios = <&gpio0 30 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_0>;
|
||||
};
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&gpio0 31 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
|
||||
power {
|
||||
label = "power";
|
||||
gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_POWER>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
status = "okay";
|
||||
|
||||
w25q64@0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <10000000>;
|
||||
m25p,chunked-io = <32>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@20000 {
|
||||
label = "firmware";
|
||||
reg = <0x20000 0x5e0000>;
|
||||
};
|
||||
|
||||
config: partition@600000 {
|
||||
label = "config";
|
||||
reg = <0x600000 0x50000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
radio: partition@7f0000 {
|
||||
label = "radio";
|
||||
reg = <0x7f0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
|
||||
pcie0 {
|
||||
mt76@0,0 {
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
device_type = "pci";
|
||||
mediatek,mtd-eeprom = <&radio 0>;
|
||||
mtd-mac-address = <&config 0x10008>;
|
||||
mtd-mac-address-increment = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
pcie1 {
|
||||
mt76@1,0 {
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
device_type = "pci";
|
||||
mediatek,mtd-eeprom = <&radio 0x8000>;
|
||||
ieee80211-freq-limit = <5000000 6000000>;
|
||||
mtd-mac-address = <&config 0x10008>;
|
||||
mtd-mac-address-increment = <2>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ðernet {
|
||||
mtd-mac-address = <&config 0x10008>;
|
||||
};
|
||||
|
||||
&pinctrl {
|
||||
state_default: pinctrl0 {
|
||||
gpio {
|
||||
ralink,group = "rgmii2", "wdt";
|
||||
ralink,function = "gpio";
|
||||
};
|
||||
};
|
||||
};
|
||||
@@ -2,6 +2,8 @@
|
||||
# MT7621 Profiles
|
||||
#
|
||||
|
||||
DEVICE_VARS += TPLINK_BOARD_ID TPLINK_HEADER_VERSION TPLINK_HWID TPLINK_HWREV
|
||||
|
||||
define Build/ubnt-erx-factory-image
|
||||
if [ -e $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE) -a "$$(stat -c%s $@)" -lt "$(KERNEL_SIZE)" ]; then \
|
||||
echo '21001:6' > $(1).compat; \
|
||||
@@ -148,6 +150,22 @@ define Device/rb750gr3
|
||||
endef
|
||||
TARGET_DEVICES += rb750gr3
|
||||
|
||||
define Device/re350-v1
|
||||
DTS := RE350
|
||||
DEVICE_TITLE := TP-LINK RE350 v1
|
||||
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 wpad-mini
|
||||
TPLINK_BOARD_ID := RE350-V1
|
||||
TPLINK_HWID := 0x0
|
||||
TPLINK_HWREV := 0
|
||||
TPLINK_HEADER_VERSION := 1
|
||||
IMAGE_SIZE := 6016k
|
||||
KERNEL := $(KERNEL_DTB) | tplink-v1-header -e
|
||||
IMAGES := sysupgrade.bin factory.bin
|
||||
IMAGE/sysupgrade.bin := append-rootfs | tplink-safeloader sysupgrade | append-metadata | check-size $$$$(IMAGE_SIZE)
|
||||
IMAGE/factory.bin := append-rootfs | tplink-safeloader factory
|
||||
endef
|
||||
TARGET_DEVICES += re350-v1
|
||||
|
||||
define Device/re6500
|
||||
DTS := RE6500
|
||||
DEVICE_TITLE := Linksys RE6500
|
||||
|
||||
@@ -163,6 +163,7 @@ CONFIG_MTD_PHYSMAP=y
|
||||
CONFIG_MTD_SPI_NOR=y
|
||||
CONFIG_MTD_SPLIT_FIRMWARE=y
|
||||
CONFIG_MTD_SPLIT_SEAMA_FW=y
|
||||
CONFIG_MTD_SPLIT_TPLINK_FW=y
|
||||
CONFIG_MTD_SPLIT_TRX_FW=y
|
||||
CONFIG_MTD_SPLIT_UIMAGE_FW=y
|
||||
CONFIG_MTD_UBI=y
|
||||
@@ -237,6 +238,7 @@ CONFIG_SPI_MT7621=y
|
||||
# CONFIG_SPI_RT2880 is not set
|
||||
CONFIG_SRCU=y
|
||||
CONFIG_SWCONFIG=y
|
||||
CONFIG_SWCONFIG_LEDS=y
|
||||
CONFIG_SYNC_R4K=y
|
||||
CONFIG_SYSCTL_EXCEPTION_TRACE=y
|
||||
CONFIG_SYS_HAS_CPU_MIPS32_R1=y
|
||||
|
||||
@@ -172,6 +172,7 @@ CONFIG_MTD_PHYSMAP=y
|
||||
CONFIG_MTD_SPI_NOR=y
|
||||
CONFIG_MTD_SPLIT_FIRMWARE=y
|
||||
CONFIG_MTD_SPLIT_SEAMA_FW=y
|
||||
CONFIG_MTD_SPLIT_TPLINK_FW=y
|
||||
CONFIG_MTD_SPLIT_TRX_FW=y
|
||||
CONFIG_MTD_SPLIT_UIMAGE_FW=y
|
||||
CONFIG_MTD_UBI=y
|
||||
@@ -251,6 +252,7 @@ CONFIG_SPI_MASTER=y
|
||||
CONFIG_SPI_MT7621=y
|
||||
# CONFIG_SPI_RT2880 is not set
|
||||
CONFIG_SRCU=y
|
||||
CONFIG_SWCONFIG_LEDS=y
|
||||
CONFIG_SWCONFIG=y
|
||||
CONFIG_SWPHY=y
|
||||
CONFIG_SYNC_R4K=y
|
||||
|
||||
Reference in New Issue
Block a user