sunxi: add support for FriendlyARM NanoPi R1S H5
Specification:
CPU: Allwinner H5, Quad-core Cortex-A53
DDR3 RAM: 512MB
Network: 10/100/1000M Ethernet x 2
USB Host: Type-A x 1
MicroSD Slot x 1
MicroUSB: for power input
Debug Serial Port: 3Pin pin-header
LED: WAN, LAN, SYS
KEY: Reset
Power Supply: DC 5V/2A
Installation:
Write the image to SD Card with dd.
Note:
1. OpenWrt currently does not support LED_FUNCTION, change back to the
previous practice (Consistent with NanoPi R1).
2. Since the upstream commit https://github.com/torvalds/linux/bbc4d71
("net: phy: realtek: fix rtl8211e rx/tx delay config"), we need to
change the phy-mode from rgmii to rgmii-id.
So set phy-mode for 5.4 and 5.10 respectively.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
This commit is contained in:
Chukun Pan
committed by
Hauke Mehrtens
Hauke Mehrtens
parent
e43eb16efe
commit
fde68cb809
@@ -7,7 +7,8 @@ boardname="${board##*,}"
|
|||||||
board_config_update
|
board_config_update
|
||||||
|
|
||||||
case $board in
|
case $board in
|
||||||
friendlyarm,nanopi-r1)
|
friendlyarm,nanopi-r1|\
|
||||||
|
friendlyarm,nanopi-r1s-h5)
|
||||||
ucidef_set_led_netdev "wan" "WAN" "nanopi:green:wan" "eth0"
|
ucidef_set_led_netdev "wan" "WAN" "nanopi:green:wan" "eth0"
|
||||||
ucidef_set_led_netdev "lan" "LAN" "nanopi:green:lan" "eth1"
|
ucidef_set_led_netdev "lan" "LAN" "nanopi:green:lan" "eth1"
|
||||||
;;
|
;;
|
||||||
|
|||||||
@@ -3,27 +3,54 @@
|
|||||||
#
|
#
|
||||||
|
|
||||||
. /lib/functions/uci-defaults.sh
|
. /lib/functions/uci-defaults.sh
|
||||||
|
. /lib/functions/system.sh
|
||||||
|
|
||||||
board_config_update
|
sunxi_setup_interfaces()
|
||||||
|
{
|
||||||
|
local board="$1"
|
||||||
|
|
||||||
case $(board_name) in
|
case "$board" in
|
||||||
friendlyarm,nanopi-r1)
|
friendlyarm,nanopi-r1|\
|
||||||
|
friendlyarm,nanopi-r1s-h5)
|
||||||
ucidef_set_interfaces_lan_wan "eth1" "eth0"
|
ucidef_set_interfaces_lan_wan "eth1" "eth0"
|
||||||
;;
|
;;
|
||||||
lamobo,lamobo-r1)
|
lamobo,lamobo-r1)
|
||||||
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" wan
|
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" wan
|
||||||
;;
|
;;
|
||||||
olimex,a20-olinuxino-micro)
|
olimex,a20-olinuxino-micro)
|
||||||
ucidef_set_interface_lan "wlan0"
|
ucidef_set_interface_lan "wlan0"
|
||||||
;;
|
;;
|
||||||
xunlong,orangepi-r1)
|
xunlong,orangepi-r1)
|
||||||
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
||||||
;;
|
;;
|
||||||
*)
|
*)
|
||||||
ucidef_set_interface_lan "eth0"
|
ucidef_set_interface_lan "eth0"
|
||||||
;;
|
;;
|
||||||
esac
|
esac
|
||||||
|
}
|
||||||
|
|
||||||
|
sunxi_setup_macs()
|
||||||
|
{
|
||||||
|
local board="$1"
|
||||||
|
local lan_mac=""
|
||||||
|
local wan_mac=""
|
||||||
|
local label_mac=""
|
||||||
|
|
||||||
|
case "$board" in
|
||||||
|
friendlyarm,nanopi-r1s-h5)
|
||||||
|
lan_mac=$(get_mac_binary "/sys/bus/i2c/devices/0-0051/eeprom" 0xfa)
|
||||||
|
;;
|
||||||
|
esac
|
||||||
|
|
||||||
|
[ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac
|
||||||
|
[ -n "$wan_mac" ] && ucidef_set_interface_macaddr "wan" $wan_mac
|
||||||
|
[ -n "$label_mac" ] && ucidef_set_label_macaddr $label_mac
|
||||||
|
}
|
||||||
|
|
||||||
|
board_config_update
|
||||||
|
board=$(board_name)
|
||||||
|
sunxi_setup_interfaces $board
|
||||||
|
sunxi_setup_macs $board
|
||||||
board_config_flush
|
board_config_flush
|
||||||
|
|
||||||
exit 0
|
exit 0
|
||||||
|
|||||||
@@ -26,6 +26,7 @@ CONFIG_AUDIT_ARCH_COMPAT_GENERIC=y
|
|||||||
CONFIG_CC_HAVE_STACKPROTECTOR_SYSREG=y
|
CONFIG_CC_HAVE_STACKPROTECTOR_SYSREG=y
|
||||||
CONFIG_DMA_DIRECT_REMAP=y
|
CONFIG_DMA_DIRECT_REMAP=y
|
||||||
CONFIG_DWMAC_SUN8I=y
|
CONFIG_DWMAC_SUN8I=y
|
||||||
|
CONFIG_EEPROM_AT24=y
|
||||||
# CONFIG_FLATMEM_MANUAL is not set
|
# CONFIG_FLATMEM_MANUAL is not set
|
||||||
CONFIG_FRAME_POINTER=y
|
CONFIG_FRAME_POINTER=y
|
||||||
CONFIG_GENERIC_BUG_RELATIVE_POINTERS=y
|
CONFIG_GENERIC_BUG_RELATIVE_POINTERS=y
|
||||||
|
|||||||
@@ -69,6 +69,7 @@ CONFIG_AUDIT_ARCH_COMPAT_GENERIC=y
|
|||||||
CONFIG_DMA_DIRECT_REMAP=y
|
CONFIG_DMA_DIRECT_REMAP=y
|
||||||
CONFIG_DRM_RCAR_WRITEBACK=y
|
CONFIG_DRM_RCAR_WRITEBACK=y
|
||||||
CONFIG_DWMAC_SUN8I=y
|
CONFIG_DWMAC_SUN8I=y
|
||||||
|
CONFIG_EEPROM_AT24=y
|
||||||
CONFIG_EFI_EARLYCON=y
|
CONFIG_EFI_EARLYCON=y
|
||||||
# CONFIG_FLATMEM_MANUAL is not set
|
# CONFIG_FLATMEM_MANUAL is not set
|
||||||
CONFIG_FRAME_POINTER=y
|
CONFIG_FRAME_POINTER=y
|
||||||
|
|||||||
@@ -40,6 +40,15 @@ define Device/friendlyarm_nanopi-neo2
|
|||||||
endef
|
endef
|
||||||
TARGET_DEVICES += friendlyarm_nanopi-neo2
|
TARGET_DEVICES += friendlyarm_nanopi-neo2
|
||||||
|
|
||||||
|
define Device/friendlyarm_nanopi-r1s-h5
|
||||||
|
DEVICE_VENDOR := FriendlyARM
|
||||||
|
DEVICE_MODEL := Nanopi R1S H5
|
||||||
|
DEVICE_PACKAGES := kmod-gpio-button-hotplug kmod-usb-net-rtl8152
|
||||||
|
SUPPORTED_DEVICES:=nanopi-r1s-h5
|
||||||
|
$(Device/sun50i-h5)
|
||||||
|
endef
|
||||||
|
TARGET_DEVICES += friendlyarm_nanopi-r1s-h5
|
||||||
|
|
||||||
define Device/libretech_all-h3-cc-h5
|
define Device/libretech_all-h3-cc-h5
|
||||||
DEVICE_VENDOR := Libre Computer
|
DEVICE_VENDOR := Libre Computer
|
||||||
DEVICE_MODEL := ALL-H3-CC
|
DEVICE_MODEL := ALL-H3-CC
|
||||||
|
|||||||
@@ -0,0 +1,230 @@
|
|||||||
|
From 9962cb9be2db877c232aaf00db40125c0d7bf4bc Mon Sep 17 00:00:00 2001
|
||||||
|
From: Chukun Pan <amadeus@jmu.edu.cn>
|
||||||
|
Date: Mon, 17 May 2021 00:35:22 +0800
|
||||||
|
Subject: [PATCH] arm64: dts: allwinner: h5: Add NanoPi R1S H5 support
|
||||||
|
|
||||||
|
The NanoPi R1S H5 is a open source board made by FriendlyElec.
|
||||||
|
It has the following features:
|
||||||
|
|
||||||
|
- Allwinner H5, Quad-core Cortex-A53
|
||||||
|
- 512MB DDR3 RAM
|
||||||
|
- 10/100/1000M Ethernet x 2
|
||||||
|
- RTL8189ETV WiFi 802.11b/g/n
|
||||||
|
- USB 2.0 host port (A)
|
||||||
|
- MicroSD Slot
|
||||||
|
- Serial Debug Port
|
||||||
|
- 5V 2A DC power-supply
|
||||||
|
|
||||||
|
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
|
||||||
|
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
||||||
|
Link: https://lore.kernel.org/r/20210516163523.9484-2-amadeus@jmu.edu.cn
|
||||||
|
---
|
||||||
|
arch/arm64/boot/dts/allwinner/Makefile | 1 +
|
||||||
|
.../dts/allwinner/sun50i-h5-nanopi-r1s-h5.dts | 195 ++++++++++++++++++
|
||||||
|
2 files changed, 196 insertions(+)
|
||||||
|
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-r1s-h5.dts
|
||||||
|
|
||||||
|
--- a/arch/arm64/boot/dts/allwinner/Makefile
|
||||||
|
+++ b/arch/arm64/boot/dts/allwinner/Makefile
|
||||||
|
@@ -24,6 +24,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-li
|
||||||
|
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-libretech-all-h5-cc.dtb
|
||||||
|
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-nanopi-neo2.dtb
|
||||||
|
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-nanopi-neo-plus2.dtb
|
||||||
|
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-nanopi-r1s-h5.dtb
|
||||||
|
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb
|
||||||
|
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-prime.dtb
|
||||||
|
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus.dtb
|
||||||
|
--- /dev/null
|
||||||
|
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-r1s-h5.dts
|
||||||
|
@@ -0,0 +1,191 @@
|
||||||
|
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
|
||||||
|
+/*
|
||||||
|
+ * Copyright (C) 2021 Chukun Pan <amadeus@jmu.edu.cn>
|
||||||
|
+ *
|
||||||
|
+ * Based on sun50i-h5-nanopi-neo-plus2.dts, which is:
|
||||||
|
+ * Copyright (C) 2017 Antony Antony <antony@phenome.org>
|
||||||
|
+ * Copyright (C) 2016 ARM Ltd.
|
||||||
|
+ */
|
||||||
|
+
|
||||||
|
+/dts-v1/;
|
||||||
|
+#include "sun50i-h5.dtsi"
|
||||||
|
+#include "sun50i-h5-cpu-opp.dtsi"
|
||||||
|
+
|
||||||
|
+#include <dt-bindings/gpio/gpio.h>
|
||||||
|
+#include <dt-bindings/input/input.h>
|
||||||
|
+
|
||||||
|
+/ {
|
||||||
|
+ model = "FriendlyARM NanoPi R1S H5";
|
||||||
|
+ compatible = "friendlyarm,nanopi-r1s-h5", "allwinner,sun50i-h5";
|
||||||
|
+
|
||||||
|
+ aliases {
|
||||||
|
+ ethernet0 = &emac;
|
||||||
|
+ ethernet1 = &rtl8189etv;
|
||||||
|
+ serial0 = &uart0;
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ chosen {
|
||||||
|
+ stdout-path = "serial0:115200n8";
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ leds {
|
||||||
|
+ compatible = "gpio-leds";
|
||||||
|
+
|
||||||
|
+ sys {
|
||||||
|
+ label = "nanopi:red:sys";
|
||||||
|
+ gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>;
|
||||||
|
+ linux,default-trigger = "heartbeat";
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ lan {
|
||||||
|
+ label = "nanopi:green:lan";
|
||||||
|
+ gpios = <&pio 0 9 GPIO_ACTIVE_HIGH>;
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ wan {
|
||||||
|
+ label = "nanopi:green:wan";
|
||||||
|
+ gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>;
|
||||||
|
+ };
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ r-gpio-keys {
|
||||||
|
+ compatible = "gpio-keys";
|
||||||
|
+
|
||||||
|
+ reset {
|
||||||
|
+ label = "reset";
|
||||||
|
+ linux,code = <KEY_RESTART>;
|
||||||
|
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
|
||||||
|
+ };
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ reg_gmac_3v3: gmac-3v3 {
|
||||||
|
+ compatible = "regulator-fixed";
|
||||||
|
+ regulator-name = "gmac-3v3";
|
||||||
|
+ regulator-min-microvolt = <3300000>;
|
||||||
|
+ regulator-max-microvolt = <3300000>;
|
||||||
|
+ startup-delay-us = <100000>;
|
||||||
|
+ enable-active-high;
|
||||||
|
+ gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ reg_vcc3v3: vcc3v3 {
|
||||||
|
+ compatible = "regulator-fixed";
|
||||||
|
+ regulator-name = "vcc3v3";
|
||||||
|
+ regulator-min-microvolt = <3300000>;
|
||||||
|
+ regulator-max-microvolt = <3300000>;
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ reg_usb0_vbus: usb0-vbus {
|
||||||
|
+ compatible = "regulator-fixed";
|
||||||
|
+ regulator-name = "usb0-vbus";
|
||||||
|
+ regulator-min-microvolt = <5000000>;
|
||||||
|
+ regulator-max-microvolt = <5000000>;
|
||||||
|
+ enable-active-high;
|
||||||
|
+ gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
|
||||||
|
+ status = "okay";
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ vdd_cpux: gpio-regulator {
|
||||||
|
+ compatible = "regulator-gpio";
|
||||||
|
+ regulator-name = "vdd-cpux";
|
||||||
|
+ regulator-type = "voltage";
|
||||||
|
+ regulator-boot-on;
|
||||||
|
+ regulator-always-on;
|
||||||
|
+ regulator-min-microvolt = <1100000>;
|
||||||
|
+ regulator-max-microvolt = <1300000>;
|
||||||
|
+ regulator-ramp-delay = <50>; /* 4ms */
|
||||||
|
+ gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>;
|
||||||
|
+ gpios-states = <0x1>;
|
||||||
|
+ states = <1100000 0x0>, <1300000 0x1>;
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ wifi_pwrseq: wifi_pwrseq {
|
||||||
|
+ compatible = "mmc-pwrseq-simple";
|
||||||
|
+ reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
|
||||||
|
+ post-power-on-delay-ms = <200>;
|
||||||
|
+ };
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+&cpu0 {
|
||||||
|
+ cpu-supply = <&vdd_cpux>;
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+&ehci1 {
|
||||||
|
+ status = "okay";
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+&ehci2 {
|
||||||
|
+ status = "okay";
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+&emac {
|
||||||
|
+ pinctrl-names = "default";
|
||||||
|
+ pinctrl-0 = <&emac_rgmii_pins>;
|
||||||
|
+ phy-supply = <®_gmac_3v3>;
|
||||||
|
+ phy-handle = <&ext_rgmii_phy>;
|
||||||
|
+ phy-mode = "rgmii-id";
|
||||||
|
+ status = "okay";
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+&external_mdio {
|
||||||
|
+ ext_rgmii_phy: ethernet-phy@7 {
|
||||||
|
+ compatible = "ethernet-phy-ieee802.3-c22";
|
||||||
|
+ reg = <7>;
|
||||||
|
+ };
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+&i2c0 {
|
||||||
|
+ status = "okay";
|
||||||
|
+
|
||||||
|
+ eeprom@51 {
|
||||||
|
+ compatible = "microchip,24c02";
|
||||||
|
+ reg = <0x51>;
|
||||||
|
+ pagesize = <16>;
|
||||||
|
+ };
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+&mmc0 {
|
||||||
|
+ vmmc-supply = <®_vcc3v3>;
|
||||||
|
+ bus-width = <4>;
|
||||||
|
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
|
||||||
|
+ status = "okay";
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+&mmc1 {
|
||||||
|
+ vmmc-supply = <®_vcc3v3>;
|
||||||
|
+ vqmmc-supply = <®_vcc3v3>;
|
||||||
|
+ mmc-pwrseq = <&wifi_pwrseq>;
|
||||||
|
+ bus-width = <4>;
|
||||||
|
+ non-removable;
|
||||||
|
+ status = "okay";
|
||||||
|
+
|
||||||
|
+ rtl8189etv: sdio_wifi@1 {
|
||||||
|
+ reg = <1>;
|
||||||
|
+ };
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+&ohci1 {
|
||||||
|
+ status = "okay";
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+&ohci2 {
|
||||||
|
+ status = "okay";
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+&uart0 {
|
||||||
|
+ pinctrl-names = "default";
|
||||||
|
+ pinctrl-0 = <&uart0_pa_pins>;
|
||||||
|
+ status = "okay";
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+&usb_otg {
|
||||||
|
+ dr_mode = "peripheral";
|
||||||
|
+ status = "okay";
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+&usbphy {
|
||||||
|
+ /* USB Type-A port's VBUS is always on */
|
||||||
|
+ usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
|
||||||
|
+ usb0_vbus-supply = <®_usb0_vbus>;
|
||||||
|
+ status = "okay";
|
||||||
|
+};
|
||||||
@@ -0,0 +1,35 @@
|
|||||||
|
From 1845163a052efac124f00656eb72f38947630a42 Mon Sep 17 00:00:00 2001
|
||||||
|
From: Chukun Pan <amadeus@jmu.edu.cn>
|
||||||
|
Date: Sun, 10 Oct 2021 21:50:18 +0800
|
||||||
|
Subject: [PATCH] arm64: dts: allwinner: NanoPi R1S H5: add status LED aliases
|
||||||
|
|
||||||
|
Use the SYS LED on the casing for showing system status.
|
||||||
|
|
||||||
|
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
|
||||||
|
---
|
||||||
|
arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-r1s-h5.dts | 7 ++++++-
|
||||||
|
1 file changed, 6 insertions(+), 1 deletion(-)
|
||||||
|
|
||||||
|
--- a/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-r1s-h5.dts
|
||||||
|
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-r1s-h5.dts
|
||||||
|
@@ -22,6 +22,11 @@
|
||||||
|
ethernet0 = &emac;
|
||||||
|
ethernet1 = &rtl8189etv;
|
||||||
|
serial0 = &uart0;
|
||||||
|
+
|
||||||
|
+ led-boot = &led_sys;
|
||||||
|
+ led-failsafe = &led_sys;
|
||||||
|
+ led-running = &led_sys;
|
||||||
|
+ led-upgrade = &led_sys;
|
||||||
|
};
|
||||||
|
|
||||||
|
chosen {
|
||||||
|
@@ -31,7 +36,7 @@
|
||||||
|
leds {
|
||||||
|
compatible = "gpio-leds";
|
||||||
|
|
||||||
|
- sys {
|
||||||
|
+ led_sys: sys {
|
||||||
|
label = "nanopi:red:sys";
|
||||||
|
gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>;
|
||||||
|
linux,default-trigger = "heartbeat";
|
||||||
@@ -0,0 +1,229 @@
|
|||||||
|
From 9962cb9be2db877c232aaf00db40125c0d7bf4bc Mon Sep 17 00:00:00 2001
|
||||||
|
From: Chukun Pan <amadeus@jmu.edu.cn>
|
||||||
|
Date: Mon, 17 May 2021 00:35:22 +0800
|
||||||
|
Subject: [PATCH] arm64: dts: allwinner: h5: Add NanoPi R1S H5 support
|
||||||
|
|
||||||
|
The NanoPi R1S H5 is a open source board made by FriendlyElec.
|
||||||
|
It has the following features:
|
||||||
|
|
||||||
|
- Allwinner H5, Quad-core Cortex-A53
|
||||||
|
- 512MB DDR3 RAM
|
||||||
|
- 10/100/1000M Ethernet x 2
|
||||||
|
- RTL8189ETV WiFi 802.11b/g/n
|
||||||
|
- USB 2.0 host port (A)
|
||||||
|
- MicroSD Slot
|
||||||
|
- Serial Debug Port
|
||||||
|
- 5V 2A DC power-supply
|
||||||
|
|
||||||
|
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
|
||||||
|
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
||||||
|
Link: https://lore.kernel.org/r/20210516163523.9484-2-amadeus@jmu.edu.cn
|
||||||
|
---
|
||||||
|
arch/arm64/boot/dts/allwinner/Makefile | 1 +
|
||||||
|
.../dts/allwinner/sun50i-h5-nanopi-r1s-h5.dts | 195 ++++++++++++++++++
|
||||||
|
2 files changed, 196 insertions(+)
|
||||||
|
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-r1s-h5.dts
|
||||||
|
|
||||||
|
--- a/arch/arm64/boot/dts/allwinner/Makefile
|
||||||
|
+++ b/arch/arm64/boot/dts/allwinner/Makefile
|
||||||
|
@@ -17,6 +17,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-em
|
||||||
|
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-libretech-all-h3-cc.dtb
|
||||||
|
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-nanopi-neo2.dtb
|
||||||
|
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-nanopi-neo-plus2.dtb
|
||||||
|
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-nanopi-r1s-h5.dtb
|
||||||
|
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb
|
||||||
|
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-prime.dtb
|
||||||
|
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus.dtb
|
||||||
|
--- /dev/null
|
||||||
|
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-r1s-h5.dts
|
||||||
|
@@ -0,0 +1,190 @@
|
||||||
|
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
|
||||||
|
+/*
|
||||||
|
+ * Copyright (C) 2021 Chukun Pan <amadeus@jmu.edu.cn>
|
||||||
|
+ *
|
||||||
|
+ * Based on sun50i-h5-nanopi-neo-plus2.dts, which is:
|
||||||
|
+ * Copyright (C) 2017 Antony Antony <antony@phenome.org>
|
||||||
|
+ * Copyright (C) 2016 ARM Ltd.
|
||||||
|
+ */
|
||||||
|
+
|
||||||
|
+/dts-v1/;
|
||||||
|
+#include "sun50i-h5.dtsi"
|
||||||
|
+
|
||||||
|
+#include <dt-bindings/gpio/gpio.h>
|
||||||
|
+#include <dt-bindings/input/input.h>
|
||||||
|
+
|
||||||
|
+/ {
|
||||||
|
+ model = "FriendlyARM NanoPi R1S H5";
|
||||||
|
+ compatible = "friendlyarm,nanopi-r1s-h5", "allwinner,sun50i-h5";
|
||||||
|
+
|
||||||
|
+ aliases {
|
||||||
|
+ ethernet0 = &emac;
|
||||||
|
+ ethernet1 = &rtl8189etv;
|
||||||
|
+ serial0 = &uart0;
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ chosen {
|
||||||
|
+ stdout-path = "serial0:115200n8";
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ leds {
|
||||||
|
+ compatible = "gpio-leds";
|
||||||
|
+
|
||||||
|
+ sys {
|
||||||
|
+ label = "nanopi:red:sys";
|
||||||
|
+ gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>;
|
||||||
|
+ linux,default-trigger = "heartbeat";
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ lan {
|
||||||
|
+ label = "nanopi:green:lan";
|
||||||
|
+ gpios = <&pio 0 9 GPIO_ACTIVE_HIGH>;
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ wan {
|
||||||
|
+ label = "nanopi:green:wan";
|
||||||
|
+ gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>;
|
||||||
|
+ };
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ r-gpio-keys {
|
||||||
|
+ compatible = "gpio-keys";
|
||||||
|
+
|
||||||
|
+ reset {
|
||||||
|
+ label = "reset";
|
||||||
|
+ linux,code = <KEY_RESTART>;
|
||||||
|
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
|
||||||
|
+ };
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ reg_gmac_3v3: gmac-3v3 {
|
||||||
|
+ compatible = "regulator-fixed";
|
||||||
|
+ regulator-name = "gmac-3v3";
|
||||||
|
+ regulator-min-microvolt = <3300000>;
|
||||||
|
+ regulator-max-microvolt = <3300000>;
|
||||||
|
+ startup-delay-us = <100000>;
|
||||||
|
+ enable-active-high;
|
||||||
|
+ gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ reg_vcc3v3: vcc3v3 {
|
||||||
|
+ compatible = "regulator-fixed";
|
||||||
|
+ regulator-name = "vcc3v3";
|
||||||
|
+ regulator-min-microvolt = <3300000>;
|
||||||
|
+ regulator-max-microvolt = <3300000>;
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ reg_usb0_vbus: usb0-vbus {
|
||||||
|
+ compatible = "regulator-fixed";
|
||||||
|
+ regulator-name = "usb0-vbus";
|
||||||
|
+ regulator-min-microvolt = <5000000>;
|
||||||
|
+ regulator-max-microvolt = <5000000>;
|
||||||
|
+ enable-active-high;
|
||||||
|
+ gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
|
||||||
|
+ status = "okay";
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ vdd_cpux: gpio-regulator {
|
||||||
|
+ compatible = "regulator-gpio";
|
||||||
|
+ regulator-name = "vdd-cpux";
|
||||||
|
+ regulator-type = "voltage";
|
||||||
|
+ regulator-boot-on;
|
||||||
|
+ regulator-always-on;
|
||||||
|
+ regulator-min-microvolt = <1100000>;
|
||||||
|
+ regulator-max-microvolt = <1300000>;
|
||||||
|
+ regulator-ramp-delay = <50>; /* 4ms */
|
||||||
|
+ gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>;
|
||||||
|
+ gpios-states = <0x1>;
|
||||||
|
+ states = <1100000 0x0>, <1300000 0x1>;
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ wifi_pwrseq: wifi_pwrseq {
|
||||||
|
+ compatible = "mmc-pwrseq-simple";
|
||||||
|
+ reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
|
||||||
|
+ post-power-on-delay-ms = <200>;
|
||||||
|
+ };
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+&cpu0 {
|
||||||
|
+ cpu-supply = <&vdd_cpux>;
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+&ehci1 {
|
||||||
|
+ status = "okay";
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+&ehci2 {
|
||||||
|
+ status = "okay";
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+&emac {
|
||||||
|
+ pinctrl-names = "default";
|
||||||
|
+ pinctrl-0 = <&emac_rgmii_pins>;
|
||||||
|
+ phy-supply = <®_gmac_3v3>;
|
||||||
|
+ phy-handle = <&ext_rgmii_phy>;
|
||||||
|
+ phy-mode = "rgmii";
|
||||||
|
+ status = "okay";
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+&external_mdio {
|
||||||
|
+ ext_rgmii_phy: ethernet-phy@7 {
|
||||||
|
+ compatible = "ethernet-phy-ieee802.3-c22";
|
||||||
|
+ reg = <7>;
|
||||||
|
+ };
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+&i2c0 {
|
||||||
|
+ status = "okay";
|
||||||
|
+
|
||||||
|
+ eeprom@51 {
|
||||||
|
+ compatible = "microchip,24c02";
|
||||||
|
+ reg = <0x51>;
|
||||||
|
+ pagesize = <16>;
|
||||||
|
+ };
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+&mmc0 {
|
||||||
|
+ vmmc-supply = <®_vcc3v3>;
|
||||||
|
+ bus-width = <4>;
|
||||||
|
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
|
||||||
|
+ status = "okay";
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+&mmc1 {
|
||||||
|
+ vmmc-supply = <®_vcc3v3>;
|
||||||
|
+ vqmmc-supply = <®_vcc3v3>;
|
||||||
|
+ mmc-pwrseq = <&wifi_pwrseq>;
|
||||||
|
+ bus-width = <4>;
|
||||||
|
+ non-removable;
|
||||||
|
+ status = "okay";
|
||||||
|
+
|
||||||
|
+ rtl8189etv: sdio_wifi@1 {
|
||||||
|
+ reg = <1>;
|
||||||
|
+ };
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+&ohci1 {
|
||||||
|
+ status = "okay";
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+&ohci2 {
|
||||||
|
+ status = "okay";
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+&uart0 {
|
||||||
|
+ pinctrl-names = "default";
|
||||||
|
+ pinctrl-0 = <&uart0_pa_pins>;
|
||||||
|
+ status = "okay";
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+&usb_otg {
|
||||||
|
+ dr_mode = "peripheral";
|
||||||
|
+ status = "okay";
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+&usbphy {
|
||||||
|
+ /* USB Type-A port's VBUS is always on */
|
||||||
|
+ usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
|
||||||
|
+ usb0_vbus-supply = <®_usb0_vbus>;
|
||||||
|
+ status = "okay";
|
||||||
|
+};
|
||||||
@@ -0,0 +1,35 @@
|
|||||||
|
From 1845163a052efac124f00656eb72f38947630a42 Mon Sep 17 00:00:00 2001
|
||||||
|
From: Chukun Pan <amadeus@jmu.edu.cn>
|
||||||
|
Date: Sun, 10 Oct 2021 21:50:18 +0800
|
||||||
|
Subject: [PATCH] arm64: dts: allwinner: NanoPi R1S H5: add status LED aliases
|
||||||
|
|
||||||
|
Use the SYS LED on the casing for showing system status.
|
||||||
|
|
||||||
|
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
|
||||||
|
---
|
||||||
|
arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-r1s-h5.dts | 7 ++++++-
|
||||||
|
1 file changed, 6 insertions(+), 1 deletion(-)
|
||||||
|
|
||||||
|
--- a/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-r1s-h5.dts
|
||||||
|
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-r1s-h5.dts
|
||||||
|
@@ -21,6 +21,11 @@
|
||||||
|
ethernet0 = &emac;
|
||||||
|
ethernet1 = &rtl8189etv;
|
||||||
|
serial0 = &uart0;
|
||||||
|
+
|
||||||
|
+ led-boot = &led_sys;
|
||||||
|
+ led-failsafe = &led_sys;
|
||||||
|
+ led-running = &led_sys;
|
||||||
|
+ led-upgrade = &led_sys;
|
||||||
|
};
|
||||||
|
|
||||||
|
chosen {
|
||||||
|
@@ -30,7 +35,7 @@
|
||||||
|
leds {
|
||||||
|
compatible = "gpio-leds";
|
||||||
|
|
||||||
|
- sys {
|
||||||
|
+ led_sys: sys {
|
||||||
|
label = "nanopi:red:sys";
|
||||||
|
gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>;
|
||||||
|
linux,default-trigger = "heartbeat";
|
||||||
Reference in New Issue
Block a user