c9cb6411c1
Hardware
--------
MediaTek MT7981 WiSoC
256MB DDR3 RAM
16MB SPI-NOR (XMC XM25QH128C)
MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
UART: 115200 8N1 3.3V
[LEDS] VCC-GND-RX-TX [ETH]
Header is located below the heatsink
Case
----
Unscrew the 4 bottom screws. Remove the top of the case by inserting a
small screwdriver into the ventilation holes and lift the top cover.
This works best by beginning near the ETH-ports. The top is clipped on
the front near the LEDs with two plastic clips. The back has a single
clip in the middle. Start at one of the back edges.
MAC-Addresses
-------------
80:AF:CA:00:F9:C6 LAN
80:AF:CA:00:F9:C7 WAN
80:AF:CA:00:F9:C6 W2
82:AF:CA:30:F9:C6 W5
Installation
------------
1. Connect to the serial port as described in the "Hardware" section.
2. Power on the device. Keep pressing the "0" key to enter the U-Boot
shell.
3. Download the OpenWrt initramfs image. Place it on an TFTP server
connected to the Cudy LAN ports. Make sure the server is reachable at
192.168.1.2. Rename the image to "cudy3000.bin"
4. Download and boot the OpenWrt initramfs image.
$ tftpboot 0x46000000 cudy3000.bin; bootm 0x46000000
5. Transfer the OpenWrt sysupgrade image to the device using scp.
Install with sysupgrade.
Note: Cudy does not yet provide a image for disabling their
signature-protection. This has happened in the past. Make sure to check
the wiki for a possible easier installation method.
Signed-off-by: David Bauer <mail@david-bauer.net>
251 lines
9.0 KiB
Makefile
251 lines
9.0 KiB
Makefile
DTS_DIR := $(DTS_DIR)/mediatek
|
|
|
|
define Image/Prepare
|
|
# For UBI we want only one extra block
|
|
rm -f $(KDIR)/ubi_mark
|
|
echo -ne '\xde\xad\xc0\xde' > $(KDIR)/ubi_mark
|
|
endef
|
|
|
|
define Build/bl2
|
|
cat $(STAGING_DIR_IMAGE)/mt7986-$1-bl2.img >> $@
|
|
endef
|
|
|
|
define Build/bl31-uboot
|
|
cat $(STAGING_DIR_IMAGE)/mt7986_$1-u-boot.fip >> $@
|
|
endef
|
|
|
|
define Build/mt7986-gpt
|
|
cp $@ $@.tmp 2>/dev/null || true
|
|
ptgen -g -o $@.tmp -a 1 -l 1024 \
|
|
$(if $(findstring sdmmc,$1), \
|
|
-H \
|
|
-t 0x83 -N bl2 -r -p 4079k@17k \
|
|
) \
|
|
-t 0x83 -N ubootenv -r -p 512k@4M \
|
|
-t 0x83 -N factory -r -p 2M@4608k \
|
|
-t 0xef -N fip -r -p 4M@6656k \
|
|
-N recovery -r -p 32M@12M \
|
|
$(if $(findstring sdmmc,$1), \
|
|
-N install -r -p 20M@44M \
|
|
-t 0x2e -N production -p $(CONFIG_TARGET_ROOTFS_PARTSIZE)M@64M \
|
|
) \
|
|
$(if $(findstring emmc,$1), \
|
|
-t 0x2e -N production -p $(CONFIG_TARGET_ROOTFS_PARTSIZE)M@64M \
|
|
)
|
|
cat $@.tmp >> $@
|
|
rm $@.tmp
|
|
endef
|
|
|
|
define Device/asus_tuf-ax4200
|
|
DEVICE_VENDOR := ASUS
|
|
DEVICE_MODEL := TUF-AX4200
|
|
DEVICE_DTS := mt7986a-asus-tuf-ax4200
|
|
DEVICE_DTS_DIR := ../dts
|
|
DEVICE_DTS_LOADADDR := 0x47000000
|
|
DEVICE_PACKAGES := kmod-usb3 kmod-mt7986-firmware mt7986-wo-firmware
|
|
IMAGES := sysupgrade.bin
|
|
KERNEL := kernel-bin | lzma | \
|
|
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
|
KERNEL_INITRAMFS := kernel-bin | lzma | \
|
|
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
TARGET_DEVICES += asus_tuf-ax4200
|
|
|
|
|
|
define Device/bananapi_bpi-r3
|
|
DEVICE_VENDOR := Bananapi
|
|
DEVICE_MODEL := BPi-R3
|
|
DEVICE_DTS := mt7986a-bananapi-bpi-r3
|
|
DEVICE_DTS_CONFIG := config-mt7986a-bananapi-bpi-r3
|
|
DEVICE_DTS_OVERLAY:= mt7986a-bananapi-bpi-r3-nor mt7986a-bananapi-bpi-r3-emmc-nor mt7986a-bananapi-bpi-r3-emmc-snand mt7986a-bananapi-bpi-r3-snand
|
|
DEVICE_DTS_DIR := ../dts
|
|
DEVICE_PACKAGES := kmod-hwmon-pwmfan kmod-i2c-gpio kmod-mt7986-firmware kmod-sfp kmod-usb3 e2fsprogs f2fsck mkf2fs mt7986-wo-firmware
|
|
IMAGES := sysupgrade.itb
|
|
KERNEL_LOADADDR := 0x44000000
|
|
KERNEL_INITRAMFS_SUFFIX := -recovery.itb
|
|
ARTIFACTS := \
|
|
emmc-preloader.bin emmc-bl31-uboot.fip \
|
|
nor-preloader.bin nor-bl31-uboot.fip \
|
|
sdcard.img.gz \
|
|
snand-preloader.bin snand-bl31-uboot.fip
|
|
ARTIFACT/emmc-preloader.bin := bl2 emmc-ddr4
|
|
ARTIFACT/emmc-bl31-uboot.fip := bl31-uboot bananapi_bpi-r3-emmc
|
|
ARTIFACT/nor-preloader.bin := bl2 nor-ddr4
|
|
ARTIFACT/nor-bl31-uboot.fip := bl31-uboot bananapi_bpi-r3-nor
|
|
ARTIFACT/snand-preloader.bin := bl2 spim-nand-ddr4
|
|
ARTIFACT/snand-bl31-uboot.fip := bl31-uboot bananapi_bpi-r3-snand
|
|
ARTIFACT/sdcard.img.gz := mt7986-gpt sdmmc |\
|
|
pad-to 17k | bl2 sdmmc-ddr4 |\
|
|
pad-to 6656k | bl31-uboot bananapi_bpi-r3-sdmmc |\
|
|
$(if $(CONFIG_TARGET_ROOTFS_INITRAMFS),\
|
|
pad-to 12M | append-image-stage initramfs-recovery.itb | check-size 44m |\
|
|
) \
|
|
pad-to 44M | bl2 spim-nand-ddr4 |\
|
|
pad-to 45M | bl31-uboot bananapi_bpi-r3-snand |\
|
|
pad-to 49M | bl2 nor-ddr4 |\
|
|
pad-to 50M | bl31-uboot bananapi_bpi-r3-nor |\
|
|
pad-to 51M | bl2 emmc-ddr4 |\
|
|
pad-to 52M | bl31-uboot bananapi_bpi-r3-emmc |\
|
|
pad-to 56M | mt7986-gpt emmc |\
|
|
$(if $(CONFIG_TARGET_ROOTFS_SQUASHFS),\
|
|
pad-to 64M | append-image squashfs-sysupgrade.itb | check-size | gzip \
|
|
)
|
|
IMAGE_SIZE := $$(shell expr 64 + $$(CONFIG_TARGET_ROOTFS_PARTSIZE))m
|
|
KERNEL := kernel-bin | gzip
|
|
KERNEL_INITRAMFS := kernel-bin | lzma | \
|
|
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
|
|
IMAGE/sysupgrade.itb := append-kernel | fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | pad-rootfs | append-metadata
|
|
DTC_FLAGS += -@ --space 32768
|
|
endef
|
|
TARGET_DEVICES += bananapi_bpi-r3
|
|
|
|
define Device/cudy_wr3000-v1
|
|
DEVICE_VENDOR := Cudy
|
|
DEVICE_MODEL := WR3000
|
|
DEVICE_VARIANT := v1
|
|
DEVICE_DTS := mt7981b-cudy-wr3000-v1
|
|
DEVICE_DTS_DIR := ../dts
|
|
DEVICE_DTS_LOADADDR := 0x47000000
|
|
IMAGES := sysupgrade.bin
|
|
IMAGE_SIZE := 15424k
|
|
SUPPORTED_DEVICES += R31
|
|
KERNEL := kernel-bin | lzma | \
|
|
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
|
KERNEL_INITRAMFS := kernel-bin | lzma | \
|
|
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
|
|
IMAGE/sysupgrade.bin := append-kernel | pad-to 128k | append-rootfs | pad-rootfs | check-size | append-metadata
|
|
DEVICE_PACKAGES := kmod-mt7981-firmware
|
|
endef
|
|
TARGET_DEVICES += cudy_wr3000-v1
|
|
|
|
define Device/mediatek_mt7986a-rfb-nand
|
|
DEVICE_VENDOR := MediaTek
|
|
DEVICE_MODEL := MT7986 rfba AP (NAND)
|
|
DEVICE_DTS := mt7986a-rfb-spim-nand
|
|
DEVICE_DTS_DIR := $(DTS_DIR)/
|
|
DEVICE_PACKAGES := kmod-mt7986-firmware mt7986-wo-firmware
|
|
SUPPORTED_DEVICES := mediatek,mt7986a-rfb-snand
|
|
UBINIZE_OPTS := -E 5
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
IMAGE_SIZE := 65536k
|
|
KERNEL_IN_UBI := 1
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-ubi | check-size $$$$(IMAGE_SIZE)
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
KERNEL = kernel-bin | lzma | \
|
|
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
|
KERNEL_INITRAMFS = kernel-bin | lzma | \
|
|
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd
|
|
DTC_FLAGS += -@ --space 32768
|
|
endef
|
|
TARGET_DEVICES += mediatek_mt7986a-rfb-nand
|
|
|
|
define Device/mediatek_mt7986b-rfb
|
|
DEVICE_VENDOR := MediaTek
|
|
DEVICE_MODEL := MTK7986 rfbb AP
|
|
DEVICE_DTS := mt7986b-rfb
|
|
DEVICE_DTS_DIR := $(DTS_DIR)/
|
|
DEVICE_PACKAGES := kmod-mt7986-firmware mt7986-wo-firmware
|
|
SUPPORTED_DEVICES := mediatek,mt7986b-rfb
|
|
UBINIZE_OPTS := -E 5
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
IMAGE_SIZE := 65536k
|
|
KERNEL_IN_UBI := 1
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-ubi | check-size $$$$(IMAGE_SIZE)
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
TARGET_DEVICES += mediatek_mt7986b-rfb
|
|
|
|
define Device/tplink_tl-xdr-common
|
|
DEVICE_VENDOR := TP-Link
|
|
DEVICE_DTS_DIR := ../dts
|
|
UBINIZE_OPTS := -E 5
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_IN_UBI := 1
|
|
UBOOTENV_IN_UBI := 1
|
|
IMAGES := sysupgrade.itb
|
|
KERNEL_INITRAMFS_SUFFIX := -recovery.itb
|
|
KERNEL := kernel-bin | gzip
|
|
KERNEL_INITRAMFS := kernel-bin | lzma | \
|
|
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
|
|
IMAGE/sysupgrade.itb := append-kernel | \
|
|
fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | append-metadata
|
|
DEVICE_PACKAGES := kmod-usb3 kmod-mt7986-firmware mt7986-wo-firmware
|
|
ARTIFACTS := preloader.bin bl31-uboot.fip
|
|
ARTIFACT/preloader.bin := bl2 spim-nand-ddr3
|
|
endef
|
|
|
|
define Device/tplink_tl-xdr4288
|
|
DEVICE_MODEL := TL-XDR4288
|
|
DEVICE_DTS := mt7986a-tplink-tl-xdr4288
|
|
ARTIFACT/bl31-uboot.fip := bl31-uboot tplink_tl-xdr4288
|
|
$(call Device/tplink_tl-xdr-common)
|
|
endef
|
|
TARGET_DEVICES += tplink_tl-xdr4288
|
|
|
|
define Device/tplink_tl-xdr6086
|
|
DEVICE_MODEL := TL-XDR6086
|
|
DEVICE_DTS := mt7986a-tplink-tl-xdr6086
|
|
ARTIFACT/bl31-uboot.fip := bl31-uboot tplink_tl-xdr6086
|
|
$(call Device/tplink_tl-xdr-common)
|
|
endef
|
|
TARGET_DEVICES += tplink_tl-xdr6086
|
|
|
|
define Device/tplink_tl-xdr6088
|
|
DEVICE_MODEL := TL-XDR6088
|
|
DEVICE_DTS := mt7986a-tplink-tl-xdr6088
|
|
ARTIFACT/bl31-uboot.fip := bl31-uboot tplink_tl-xdr6088
|
|
$(call Device/tplink_tl-xdr-common)
|
|
endef
|
|
TARGET_DEVICES += tplink_tl-xdr6088
|
|
|
|
define Device/xiaomi_redmi-router-ax6000-stock
|
|
DEVICE_VENDOR := Xiaomi
|
|
DEVICE_MODEL := Redmi Router AX6000 (stock layout)
|
|
DEVICE_DTS := mt7986a-xiaomi-redmi-router-ax6000-stock
|
|
DEVICE_DTS_DIR := ../dts
|
|
DEVICE_PACKAGES := kmod-leds-ws2812b kmod-mt7986-firmware mt7986-wo-firmware
|
|
UBINIZE_OPTS := -E 5
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),)
|
|
ARTIFACTS := initramfs-factory.ubi
|
|
ARTIFACT/initramfs-factory.ubi := append-image-stage initramfs-kernel.bin | ubinize-kernel
|
|
endif
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
TARGET_DEVICES += xiaomi_redmi-router-ax6000-stock
|
|
|
|
define Device/xiaomi_redmi-router-ax6000-ubootmod
|
|
DEVICE_VENDOR := Xiaomi
|
|
DEVICE_MODEL := Redmi Router AX6000 (OpenWrt U-Boot layout)
|
|
DEVICE_DTS := mt7986a-xiaomi-redmi-router-ax6000-ubootmod
|
|
DEVICE_DTS_DIR := ../dts
|
|
DEVICE_PACKAGES := kmod-leds-ws2812b kmod-mt7986-firmware mt7986-wo-firmware
|
|
KERNEL_INITRAMFS_SUFFIX := -recovery.itb
|
|
IMAGES := sysupgrade.itb
|
|
UBINIZE_OPTS := -E 5
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_IN_UBI := 1
|
|
UBOOTENV_IN_UBI := 1
|
|
KERNEL := kernel-bin | gzip
|
|
KERNEL_INITRAMFS := kernel-bin | lzma | \
|
|
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
|
|
IMAGE/sysupgrade.itb := append-kernel | \
|
|
fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | append-metadata
|
|
ARTIFACTS := preloader.bin bl31-uboot.fip
|
|
ARTIFACT/preloader.bin := bl2 spim-nand-ddr4
|
|
ARTIFACT/bl31-uboot.fip := bl31-uboot xiaomi_redmi-router-ax6000
|
|
ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),)
|
|
ARTIFACTS += initramfs-factory.ubi
|
|
ARTIFACT/initramfs-factory.ubi := append-image-stage initramfs-recovery.itb | ubinize-kernel
|
|
endif
|
|
endef
|
|
TARGET_DEVICES += xiaomi_redmi-router-ax6000-ubootmod
|