Initial commit

2025-06-24 15:51:28 +02:00
commit 22031d9dab
6862 changed files with 1462554 additions and 0 deletions
--- a/target/linux/sunxi/Makefile
+++ b/target/linux/sunxi/Makefile
@@ -0,0 +1,32 @@
+#
+# Copyright (C) 2013-2016 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+include $(TOPDIR)/rules.mk
+
+ARCH:=arm
+BOARD:=sunxi
+BOARDNAME:=Allwinner A1x/A20/A3x
+FEATURES:=fpu usb ext4 display rtc squashfs
+SUBTARGETS:=cortexa8 cortexa7 cortexa53
+MAINTAINER:=Zoltan HERPAI <wigyori@uid0.hu>
+
+KERNEL_PATCHVER:=4.14
+KERNELNAME:=zImage dtbs
+
+# A10: Cortex-A8
+# A13: Cortex-A8
+# A20: dual Cortex-A7
+# A31: quad Cortex-A7
+# A80: octa Cortex-A15/A7
+# H3: quad Cortex-A7
+
+include $(INCLUDE_DIR)/target.mk
+
+DEFAULT_PACKAGES += uboot-envtools
+DEFAULT_PACKAGES += partx-utils mkf2fs e2fsprogs
+
+$(eval $(call BuildTarget))
--- a/target/linux/sunxi/base-files/etc/board.d/02_network
+++ b/target/linux/sunxi/base-files/etc/board.d/02_network
@@ -0,0 +1,28 @@
+#!/bin/sh
+#
+# Copyright (C) 2013-2015 OpenWrt.org
+#
+
+. /lib/functions/uci-defaults.sh
+
+board_config_update
+
+case "$(board_name)" in
+"olimex,a20-olinuxino-micro")
+	ucidef_set_interface_lan 'wlan0'
+	;;
+"lamobo,lamobo-r1")
+	ucidef_add_switch "switch0" \
+		"4:lan:1" "0:lan:2" "1:lan:3" "2:lan:4" "3:wan" "8@eth0"
+	;;
+"xunlong,orangepi-r1")
+	ucidef_set_interfaces_lan_wan "eth0" "eth1"
+	;;
+*)
+	ucidef_set_interface_lan 'eth0'
+	;;
+esac
+
+board_config_flush
+
+exit 0
--- a/target/linux/sunxi/base-files/etc/inittab
+++ b/target/linux/sunxi/base-files/etc/inittab
@@ -0,0 +1,5 @@
+::sysinit:/etc/init.d/rcS S boot
+::shutdown:/etc/init.d/rcS K shutdown
+tts/0::askfirst:/usr/libexec/login.sh
+ttyS0::askfirst:/usr/libexec/login.sh
+tty1::askfirst:/usr/libexec/login.sh
--- a/target/linux/sunxi/base-files/lib/firmware/brcm/brcmfmac4329-sdio.txt
+++ b/target/linux/sunxi/base-files/lib/firmware/brcm/brcmfmac4329-sdio.txt
@@ -0,0 +1,57 @@
+#AP6210_NVRAM_V1.2_03192013
+manfid=0x2d0
+prodid=0x492
+vendid=0x14e4
+devid=0x4343
+boardtype=0x0598
+
+# Board Revision is P307, same nvram file can be used for P304, P305, P306 and P307 as the tssi pa params used are same
+#Please force the automatic RX PER data to the respective board directory if not using P307 board, for e.g. for P305 boards force the data into the following directory /projects/BCM43362/a1_labdata/boardtests/results/sdg_rev0305
+boardrev=0x1307
+boardnum=777
+xtalfreq=26000
+boardflags=0x80201
+boardflags2=0x80
+sromrev=3
+wl0id=0x431b
+macaddr=00:90:4c:07:71:12
+aa2g=1
+ag0=2
+maxp2ga0=74
+cck2gpo=0x2222
+ofdm2gpo=0x44444444
+mcs2gpo0=0x6666
+mcs2gpo1=0x6666
+pa0maxpwr=56
+
+#P207 PA params
+#pa0b0=5447
+#pa0b1=-658
+#pa0b2=-175<div></div>
+
+#Same PA params for P304,P305, P306, P307
+
+pa0b0=5447
+pa0b1=-607
+pa0b2=-160
+pa0itssit=62
+pa1itssit=62
+
+
+cckPwrOffset=5
+ccode=0
+rssismf2g=0xa
+rssismc2g=0x3
+rssisav2g=0x7
+triso2g=0
+noise_cal_enable_2g=0
+noise_cal_po_2g=0
+swctrlmap_2g=0x04040404,0x02020202,0x02020202,0x010101,0x1ff
+temp_add=29767
+temp_mult=425
+
+btc_flags=0x6
+btc_params0=5000
+btc_params1=1000
+btc_params6=63
+
--- a/target/linux/sunxi/base-files/lib/firmware/brcm/brcmfmac43362-sdio.txt
+++ b/target/linux/sunxi/base-files/lib/firmware/brcm/brcmfmac43362-sdio.txt
@@ -0,0 +1,51 @@
+#AP6181_NVRAM_V1.1_01152013
+#adjuest PA parameter for g/n mode
+manfid=0x2d0
+prodid=0x492
+vendid=0x14e4
+devid=0x4343
+boardtype=0x0598
+
+# Board Revision is P307, same nvram file can be used for P304, P305, P306 and P307 as the tssi pa params used are same
+#Please force the automatic RX PER data to the respective board directory if not using P307 board, for e.g. for P305 boards force the data into the following directory /projects/BCM43362/a1_labdata/boardtests/results/sdg_rev0305
+boardrev=0x1307
+boardnum=777
+xtalfreq=26000
+boardflags=0xa00
+sromrev=3
+wl0id=0x431b
+macaddr=00:90:4c:07:71:12
+aa2g=1
+ag0=2
+maxp2ga0=74
+cck2gpo=0x2222
+ofdm2gpo=0x66666666
+mcs2gpo0=0x7777
+mcs2gpo1=0x7777
+pa0maxpwr=56
+
+#P207 PA params
+#pa0b0=5447
+#pa0b1=-658
+#pa0b2=-175<div></div>
+
+#Same PA params for P304,P305, P306, P307
+
+pa0b0=5447
+pa0b1=-607
+pa0b2=-160
+pa0itssit=62
+pa1itssit=62
+
+
+cckPwrOffset=5
+ccode=0
+rssismf2g=0xa
+rssismc2g=0x3
+rssisav2g=0x7
+triso2g=0
+noise_cal_enable_2g=0
+noise_cal_po_2g=0
+swctrlmap_2g=0x04040404,0x02020202,0x02020202,0x010101,0x1ff
+temp_add=29767
+temp_mult=425
--- a/target/linux/sunxi/base-files/lib/firmware/brcm/brcmfmac43430-sdio.txt
+++ b/target/linux/sunxi/base-files/lib/firmware/brcm/brcmfmac43430-sdio.txt
@@ -0,0 +1,53 @@
+#AP6212_NVRAM_V1.0_20140603
+# 2.4 GHz, 20 MHz BW mode
+
+# The following parameter values are just placeholders, need to be updated.
+manfid=0x2d0
+prodid=0x0726
+vendid=0x14e4
+devid=0x43e2
+boardtype=0x0726
+boardrev=0x1101
+boardnum=22
+macaddr=00:90:4c:c5:12:38
+sromrev=11
+boardflags=0x00404201
+xtalfreq=26000
+nocrc=1
+ag0=255
+aa2g=1
+ccode=ALL
+
+pa0itssit=0x20
+extpagain2g=0
+
+#PA parameters for 2.4GHz, measured at CHIP OUTPUT
+pa2ga0=-168,7161,-820
+AvVmid_c0=0x0,0xc8
+cckpwroffset0=5
+
+# PPR params
+maxp2ga0=90
+txpwrbckof=6
+cckbw202gpo=0x5555
+legofdmbw202gpo=0x77777777
+mcsbw202gpo=0xaaaaaaaa
+
+# OFDM IIR :
+ofdmdigfilttype=7
+# PAPD mode:
+papdmode=2
+
+il0macaddr=00:90:4c:c5:12:38
+wl0id=0x431b
+
+#OOB parameters
+hostwake=0x40
+hostrdy=0x41
+usbrdy=0x03
+usbrdydelay=100
+deadman_to=0xffffffff
+# muxenab: 0x1 for UART enable, 0x10 for Host awake
+muxenab=0x10
+# CLDO PWM voltage settings - 0x4 - 1.1 volt
+#cldo_pwm=0x4
--- a/target/linux/sunxi/base-files/lib/preinit/03_b53_hack.sh
+++ b/target/linux/sunxi/base-files/lib/preinit/03_b53_hack.sh
@@ -0,0 +1,18 @@
+#!/bin/sh
+
+do_b53_hack() {
+	. /lib/functions.sh
+
+	# hack: enable switch on Lamobo R1 and reset counters
+	case "$(board_name)" in
+	"lamobo,lamobo-r1")
+		ifconfig eth0 up
+		sleep 1
+		swconfig dev switch0 set reset 1
+		swconfig dev switch0 set reset_mib 1
+		swconfig dev switch0 set apply 1
+		;;
+	esac
+}
+
+boot_hook_add preinit_main do_b53_hack
--- a/target/linux/sunxi/base-files/lib/preinit/79_move_config
+++ b/target/linux/sunxi/base-files/lib/preinit/79_move_config
@@ -0,0 +1,20 @@
+#!/bin/sh
+# Copyright (C) 2012-2015 OpenWrt.org
+
+move_config() {
+	local partdev
+
+	. /lib/upgrade/common.sh
+
+	if export_bootdevice && export_partdevice partdev -1; then
+		if mount -t vfat -o rw,noatime "/dev/$partdev" /mnt; then
+			if [ -f /mnt/sysupgrade.tgz ]; then
+				mv -f /mnt/sysupgrade.tgz /
+			fi
+			umount /mnt
+		fi
+	fi
+}
+
+boot_hook_add preinit_mount_root move_config
+
--- a/target/linux/sunxi/base-files/lib/upgrade/platform.sh
+++ b/target/linux/sunxi/base-files/lib/upgrade/platform.sh
@@ -0,0 +1,89 @@
+platform_check_image() {
+	local diskdev partdev diff
+
+	export_bootdevice && export_partdevice diskdev -2 || {
+		echo "Unable to determine upgrade device"
+		return 1
+	}
+
+	get_partitions "/dev/$diskdev" bootdisk
+
+	#extract the boot sector from the image
+	get_image "$@" | dd of=/tmp/image.bs count=1 bs=512b 2>/dev/null
+
+	get_partitions /tmp/image.bs image
+
+	#compare tables
+	diff="$(grep -F -x -v -f /tmp/partmap.bootdisk /tmp/partmap.image)"
+
+	rm -f /tmp/image.bs /tmp/partmap.bootdisk /tmp/partmap.image
+
+	if [ -n "$diff" ]; then
+		echo "Partition layout has changed. Full image will be written."
+		ask_bool 0 "Abort" && exit 1
+		return 0
+	fi
+}
+
+platform_copy_config() {
+	local partdev
+
+	if export_partdevice partdev -1; then
+		mount -t vfat -o rw,noatime "/dev/$partdev" /mnt
+		cp -af "$CONF_TAR" /mnt/
+		umount /mnt
+	fi
+}
+
+platform_do_upgrade() {
+	local diskdev partdev diff
+
+	export_bootdevice && export_partdevice diskdev -2 || {
+		echo "Unable to determine upgrade device"
+		return 1
+	}
+
+	sync
+
+	if [ "$SAVE_PARTITIONS" = "1" ]; then
+		get_partitions "/dev/$diskdev" bootdisk
+
+		#extract the boot sector from the image
+		get_image "$@" | dd of=/tmp/image.bs count=1 bs=512b
+
+		get_partitions /tmp/image.bs image
+
+		#compare tables
+		diff="$(grep -F -x -v -f /tmp/partmap.bootdisk /tmp/partmap.image)"
+	else
+		diff=1
+	fi
+
+	if [ -n "$diff" ]; then
+		get_image "$@" | dd of="/dev/$diskdev" bs=4096 conv=fsync
+
+		# Separate removal and addtion is necessary; otherwise, partition 1
+		# will be missing if it overlaps with the old partition 2
+		partx -d - "/dev/$diskdev"
+		partx -a - "/dev/$diskdev"
+
+		return 0
+	fi
+
+	#write uboot image
+	get_image "$@" | dd of="$diskdev" bs=1024 skip=8 seek=8 count=1016 conv=fsync
+	#iterate over each partition from the image and write it to the boot disk
+	while read part start size; do
+		part="$(($part - 2))"
+		if export_partdevice partdev $part; then
+			echo "Writing image to /dev/$partdev..."
+			get_image "$@" | dd of="/dev/$partdev" ibs="512" obs=1M skip="$start" count="$size" conv=fsync
+		else
+			echo "Unable to find partition $part device, skipped."
+		fi
+	done < /tmp/partmap.image
+
+	#copy partition uuid
+	echo "Writing new UUID to /dev/$diskdev..."
+	get_image "$@" | dd of="/dev/$diskdev" bs=1 skip=440 count=4 seek=440 conv=fsync
+}
--- a/target/linux/sunxi/config-4.14
+++ b/target/linux/sunxi/config-4.14
@@ -0,0 +1,596 @@
+# CONFIG_AHCI_SUNXI is not set
+CONFIG_ALIGNMENT_TRAP=y
+# CONFIG_ARCH_AXXIA is not set
+CONFIG_ARCH_CLOCKSOURCE_DATA=y
+CONFIG_ARCH_HAS_DEBUG_VIRTUAL=y
+CONFIG_ARCH_HAS_ELF_RANDOMIZE=y
+CONFIG_ARCH_HAS_GCOV_PROFILE_ALL=y
+CONFIG_ARCH_HAS_RESET_CONTROLLER=y
+CONFIG_ARCH_HAS_SET_MEMORY=y
+CONFIG_ARCH_HAS_SG_CHAIN=y
+CONFIG_ARCH_HAS_STRICT_KERNEL_RWX=y
+CONFIG_ARCH_HAS_STRICT_MODULE_RWX=y
+CONFIG_ARCH_HAS_TICK_BROADCAST=y
+CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y
+CONFIG_ARCH_HIBERNATION_POSSIBLE=y
+CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y
+CONFIG_ARCH_MULTIPLATFORM=y
+# CONFIG_ARCH_MULTI_CPU_AUTO is not set
+CONFIG_ARCH_MULTI_V6_V7=y
+CONFIG_ARCH_MULTI_V7=y
+CONFIG_ARCH_NR_GPIO=416
+CONFIG_ARCH_OPTIONAL_KERNEL_RWX=y
+CONFIG_ARCH_OPTIONAL_KERNEL_RWX_DEFAULT=y
+CONFIG_ARCH_PHYS_ADDR_T_64BIT=y
+# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
+# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
+CONFIG_ARCH_SUNXI=y
+CONFIG_ARCH_SUPPORTS_ATOMIC_RMW=y
+CONFIG_ARCH_SUPPORTS_BIG_ENDIAN=y
+CONFIG_ARCH_SUPPORTS_UPROBES=y
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_ARCH_USE_BUILTIN_BSWAP=y
+CONFIG_ARCH_USE_CMPXCHG_LOCKREF=y
+CONFIG_ARCH_WANT_GENERAL_HUGETLB=y
+CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
+CONFIG_ARM=y
+CONFIG_ARM_APPENDED_DTB=y
+CONFIG_ARM_ARCH_TIMER=y
+CONFIG_ARM_ARCH_TIMER_EVTSTREAM=y
+CONFIG_ARM_ATAG_DTB_COMPAT=y
+# CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND is not set
+CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_FROM_BOOTLOADER=y
+CONFIG_ARM_CPU_SUSPEND=y
+CONFIG_ARM_ERRATA_643719=y
+CONFIG_ARM_GIC=y
+CONFIG_ARM_HAS_SG_CHAIN=y
+CONFIG_ARM_HEAVY_MB=y
+CONFIG_ARM_L1_CACHE_SHIFT=6
+CONFIG_ARM_L1_CACHE_SHIFT_6=y
+CONFIG_ARM_LPAE=y
+CONFIG_ARM_PATCH_IDIV=y
+CONFIG_ARM_PATCH_PHYS_VIRT=y
+CONFIG_ARM_PMU=y
+CONFIG_ARM_PSCI=y
+CONFIG_ARM_PSCI_FW=y
+CONFIG_ARM_THUMB=y
+# CONFIG_ARM_THUMBEE is not set
+CONFIG_ARM_UNWIND=y
+CONFIG_ARM_VIRT_EXT=y
+CONFIG_ATA=y
+CONFIG_ATAGS=y
+# CONFIG_ATA_SFF is not set
+CONFIG_AUTO_ZRELADDR=y
+CONFIG_AXP20X_POWER=y
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
+CONFIG_BACKLIGHT_LCD_SUPPORT=y
+CONFIG_BACKLIGHT_PWM=y
+CONFIG_BINFMT_MISC=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_SCSI_REQUEST=y
+CONFIG_BOUNCE=y
+# CONFIG_BPF_SYSCALL is not set
+CONFIG_CACHE_L2X0=y
+CONFIG_CAN=y
+CONFIG_CLKDEV_LOOKUP=y
+CONFIG_CLKSRC_MMIO=y
+CONFIG_CLONE_BACKWARDS=y
+CONFIG_COMMON_CLK=y
+CONFIG_CONFIGFS_FS=y
+CONFIG_CONNECTOR=y
+CONFIG_CONSOLE_TRANSLATIONS=y
+CONFIG_COREDUMP=y
+CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS=y
+CONFIG_CPUFREQ_DT=y
+CONFIG_CPUFREQ_DT_PLATDEV=y
+CONFIG_CPU_32v6K=y
+CONFIG_CPU_32v7=y
+CONFIG_CPU_ABRT_EV7=y
+# CONFIG_CPU_BIG_ENDIAN is not set
+# CONFIG_CPU_BPREDICT_DISABLE is not set
+CONFIG_CPU_CACHE_V7=y
+CONFIG_CPU_CACHE_VIPT=y
+CONFIG_CPU_COPY_V6=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
+CONFIG_CPU_FREQ=y
+CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
+CONFIG_CPU_FREQ_GOV_ATTR_SET=y
+CONFIG_CPU_FREQ_GOV_COMMON=y
+CONFIG_CPU_FREQ_GOV_CONSERVATIVE=y
+CONFIG_CPU_FREQ_GOV_ONDEMAND=y
+CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
+CONFIG_CPU_FREQ_GOV_POWERSAVE=y
+CONFIG_CPU_FREQ_GOV_USERSPACE=y
+CONFIG_CPU_FREQ_STAT=y
+CONFIG_CPU_HAS_ASID=y
+# CONFIG_CPU_HOTPLUG_STATE_CONTROL is not set
+# CONFIG_CPU_ICACHE_DISABLE is not set
+CONFIG_CPU_PABRT_V7=y
+CONFIG_CPU_PM=y
+CONFIG_CPU_RMAP=y
+CONFIG_CPU_THERMAL=y
+CONFIG_CPU_THUMB_CAPABLE=y
+CONFIG_CPU_TLB_V7=y
+CONFIG_CPU_V7=y
+CONFIG_CRC16=y
+CONFIG_CRC_T10DIF=y
+CONFIG_CRYPTO_AEAD=y
+CONFIG_CRYPTO_AEAD2=y
+CONFIG_CRYPTO_CRC32=y
+CONFIG_CRYPTO_CRC32C=y
+CONFIG_CRYPTO_CRCT10DIF=y
+CONFIG_CRYPTO_DES=y
+CONFIG_CRYPTO_DEV_SUN4I_SS=y
+CONFIG_CRYPTO_DEV_SUN4I_SS_PRNG=y
+CONFIG_CRYPTO_HASH=y
+CONFIG_CRYPTO_HASH2=y
+CONFIG_CRYPTO_HW=y
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_MANAGER2=y
+CONFIG_CRYPTO_MD5=y
+CONFIG_CRYPTO_NULL2=y
+CONFIG_CRYPTO_RNG=y
+CONFIG_CRYPTO_RNG2=y
+CONFIG_CRYPTO_SHA1=y
+CONFIG_CRYPTO_WORKQUEUE=y
+CONFIG_DCACHE_WORD_ACCESS=y
+CONFIG_DEBUG_BUGVERBOSE=y
+CONFIG_DEBUG_LL_INCLUDE="mach/debug-macro.S"
+CONFIG_DEBUG_MEMORY_INIT=y
+# CONFIG_DEBUG_UART_8250 is not set
+# CONFIG_DEBUG_USER is not set
+CONFIG_DEFAULT_CFQ=y
+# CONFIG_DEFAULT_DEADLINE is not set
+CONFIG_DEFAULT_IOSCHED="cfq"
+CONFIG_DMADEVICES=y
+CONFIG_DMA_ENGINE=y
+CONFIG_DMA_OF=y
+CONFIG_DMA_SUN4I=y
+CONFIG_DMA_SUN6I=y
+CONFIG_DMA_VIRTUAL_CHANNELS=y
+CONFIG_DNOTIFY=y
+CONFIG_DTC=y
+CONFIG_DUMMY_CONSOLE=y
+# CONFIG_DWMAC_DWC_QOS_ETH is not set
+CONFIG_DWMAC_GENERIC=y
+# CONFIG_DWMAC_SUN8I is not set
+CONFIG_DWMAC_SUNXI=y
+CONFIG_DYNAMIC_DEBUG=y
+CONFIG_EDAC_ATOMIC_SCRUB=y
+CONFIG_EDAC_SUPPORT=y
+CONFIG_ELF_CORE=y
+# CONFIG_EMBEDDED is not set
+CONFIG_ENABLE_MUST_CHECK=y
+# CONFIG_ENABLE_WARN_DEPRECATED is not set
+CONFIG_EXT4_FS=y
+CONFIG_EXTCON=y
+# CONFIG_F2FS_CHECK_FS is not set
+CONFIG_F2FS_FS=y
+# CONFIG_F2FS_FS_SECURITY is not set
+CONFIG_F2FS_FS_XATTR=y
+CONFIG_F2FS_STAT_FS=y
+CONFIG_FAT_FS=y
+CONFIG_FB=y
+CONFIG_FB_CFB_COPYAREA=y
+CONFIG_FB_CFB_FILLRECT=y
+CONFIG_FB_CFB_IMAGEBLIT=y
+CONFIG_FB_CMDLINE=y
+CONFIG_FB_FOREIGN_ENDIAN=y
+CONFIG_FB_LITTLE_ENDIAN=y
+CONFIG_FB_MODE_HELPERS=y
+# CONFIG_FB_PROVIDE_GET_FB_UNMAPPED_AREA is not set
+CONFIG_FB_SIMPLE=y
+CONFIG_FB_TILEBLITTING=y
+CONFIG_FIXED_PHY=y
+CONFIG_FIX_EARLYCON_MEM=y
+# CONFIG_FONTS is not set
+CONFIG_FONT_8x16=y
+CONFIG_FONT_8x8=y
+CONFIG_FONT_SUPPORT=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
+CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
+CONFIG_FRAME_WARN=2048
+CONFIG_FREEZER=y
+CONFIG_FS_MBCACHE=y
+CONFIG_FS_POSIX_ACL=y
+CONFIG_GENERIC_ALLOCATOR=y
+CONFIG_GENERIC_ARCH_TOPOLOGY=y
+CONFIG_GENERIC_BUG=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
+CONFIG_GENERIC_CPU_AUTOPROBE=y
+CONFIG_GENERIC_EARLY_IOREMAP=y
+CONFIG_GENERIC_IDLE_POLL_SETUP=y
+CONFIG_GENERIC_IO=y
+CONFIG_GENERIC_IRQ_CHIP=y
+CONFIG_GENERIC_IRQ_EFFECTIVE_AFF_MASK=y
+CONFIG_GENERIC_IRQ_SHOW=y
+CONFIG_GENERIC_IRQ_SHOW_LEVEL=y
+CONFIG_GENERIC_PCI_IOMAP=y
+CONFIG_GENERIC_PHY=y
+CONFIG_GENERIC_PINCONF=y
+CONFIG_GENERIC_SCHED_CLOCK=y
+CONFIG_GENERIC_SMP_IDLE_THREAD=y
+CONFIG_GENERIC_STRNCPY_FROM_USER=y
+CONFIG_GENERIC_STRNLEN_USER=y
+CONFIG_GENERIC_TIME_VSYSCALL=y
+CONFIG_GLOB=y
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_AXP209=y
+CONFIG_GPIO_SYSFS=y
+# CONFIG_GRO_CELLS is not set
+CONFIG_HANDLE_DOMAIN_IRQ=y
+CONFIG_HARDIRQS_SW_RESEND=y
+CONFIG_HAS_DMA=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT_MAP=y
+# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set
+CONFIG_HAVE_ARCH_AUDITSYSCALL=y
+CONFIG_HAVE_ARCH_BITREVERSE=y
+CONFIG_HAVE_ARCH_JUMP_LABEL=y
+CONFIG_HAVE_ARCH_KGDB=y
+CONFIG_HAVE_ARCH_PFN_VALID=y
+CONFIG_HAVE_ARCH_SECCOMP_FILTER=y
+CONFIG_HAVE_ARCH_TRACEHOOK=y
+CONFIG_HAVE_ARCH_TRANSPARENT_HUGEPAGE=y
+CONFIG_HAVE_ARM_ARCH_TIMER=y
+CONFIG_HAVE_ARM_SMCCC=y
+# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set
+CONFIG_HAVE_CC_STACKPROTECTOR=y
+CONFIG_HAVE_CLK=y
+CONFIG_HAVE_CLK_PREPARE=y
+CONFIG_HAVE_CONTEXT_TRACKING=y
+CONFIG_HAVE_C_RECORDMCOUNT=y
+CONFIG_HAVE_DEBUG_KMEMLEAK=y
+CONFIG_HAVE_DMA_API_DEBUG=y
+CONFIG_HAVE_DMA_CONTIGUOUS=y
+CONFIG_HAVE_DYNAMIC_FTRACE=y
+CONFIG_HAVE_DYNAMIC_FTRACE_WITH_REGS=y
+CONFIG_HAVE_EBPF_JIT=y
+CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y
+CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_HAVE_GENERIC_GUP=y
+CONFIG_HAVE_HW_BREAKPOINT=y
+CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y
+CONFIG_HAVE_KVM_ARCH_TLB_FLUSH_ALL=y
+CONFIG_HAVE_KVM_CPU_RELAX_INTERCEPT=y
+CONFIG_HAVE_KVM_EVENTFD=y
+CONFIG_HAVE_KVM_IRQCHIP=y
+CONFIG_HAVE_KVM_IRQFD=y
+CONFIG_HAVE_KVM_IRQ_ROUTING=y
+CONFIG_HAVE_KVM_MSI=y
+CONFIG_HAVE_MEMBLOCK=y
+CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
+CONFIG_HAVE_NET_DSA=y
+CONFIG_HAVE_OPROFILE=y
+CONFIG_HAVE_OPTPROBES=y
+CONFIG_HAVE_PERF_EVENTS=y
+CONFIG_HAVE_PERF_REGS=y
+CONFIG_HAVE_PERF_USER_STACK_DUMP=y
+CONFIG_HAVE_PROC_CPU=y
+CONFIG_HAVE_RCU_TABLE_FREE=y
+CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
+CONFIG_HAVE_SMP=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
+CONFIG_HAVE_UID16=y
+CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=y
+CONFIG_HIGHMEM=y
+CONFIG_HIGHPTE=y
+CONFIG_HOTPLUG_CPU=y
+# CONFIG_HUGETLBFS is not set
+CONFIG_HWMON=y
+CONFIG_HW_CONSOLE=y
+CONFIG_HW_RANDOM=y
+CONFIG_HW_RANDOM_TIMERIOMEM=y
+CONFIG_HZ_FIXED=0
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_COMPAT=y
+CONFIG_I2C_HELPER_AUTO=y
+CONFIG_I2C_MV64XXX=y
+CONFIG_I2C_SUN6I_P2WI=y
+CONFIG_IIO=y
+# CONFIG_IIO_BUFFER is not set
+# CONFIG_IIO_TRIGGER is not set
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_INPUT=y
+CONFIG_INPUT_AXP20X_PEK=y
+CONFIG_INPUT_KEYBOARD=y
+CONFIG_INPUT_MOUSEDEV=y
+CONFIG_INPUT_MOUSEDEV_PSAUX=y
+CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
+CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
+CONFIG_INPUT_TOUCHSCREEN=y
+CONFIG_IOMMU_HELPER=y
+CONFIG_IOSCHED_CFQ=y
+CONFIG_IRQCHIP=y
+CONFIG_IRQ_DOMAIN=y
+CONFIG_IRQ_DOMAIN_HIERARCHY=y
+CONFIG_IRQ_FORCED_THREADING=y
+CONFIG_IRQ_WORK=y
+CONFIG_JBD2=y
+CONFIG_KALLSYMS=y
+# CONFIG_KERNEL_MODE_NEON is not set
+CONFIG_KEYBOARD_SUN4I_LRADC=y
+CONFIG_KSM=y
+CONFIG_KVM=y
+CONFIG_KVM_ARM_HOST=y
+CONFIG_KVM_GENERIC_DIRTYLOG_READ_PROTECT=y
+CONFIG_KVM_MMIO=y
+CONFIG_KVM_VFIO=y
+CONFIG_LCD_CLASS_DEVICE=y
+CONFIG_LCD_PLATFORM=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+CONFIG_LIBFDT=y
+CONFIG_LOCK_SPIN_ON_OWNER=y
+CONFIG_LOGO=y
+CONFIG_LOGO_LINUX_CLUT224=y
+CONFIG_LOGO_LINUX_MONO=y
+CONFIG_LOGO_LINUX_VGA16=y
+CONFIG_MACH_SUN4I=y
+CONFIG_MACH_SUN5I=y
+CONFIG_MACH_SUN6I=y
+CONFIG_MACH_SUN7I=y
+CONFIG_MACH_SUN8I=y
+CONFIG_MACH_SUN9I=y
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_MDIO_BUS=y
+CONFIG_MDIO_DEVICE=y
+CONFIG_MDIO_SUN4I=y
+CONFIG_MEDIA_SUPPORT=y
+# CONFIG_MFD_AC100 is not set
+CONFIG_MFD_AXP20X=y
+CONFIG_MFD_AXP20X_I2C=y
+CONFIG_MFD_AXP20X_RSB=y
+CONFIG_MFD_CORE=y
+CONFIG_MFD_SUN6I_PRCM=y
+CONFIG_MFD_SYSCON=y
+CONFIG_MIGHT_HAVE_CACHE_L2X0=y
+CONFIG_MIGHT_HAVE_PCI=y
+CONFIG_MIGRATION=y
+CONFIG_MMC=y
+CONFIG_MMC_BLOCK=y
+CONFIG_MMC_SUNXI=y
+CONFIG_MMU_NOTIFIER=y
+CONFIG_MODULES_TREE_LOOKUP=y
+CONFIG_MODULES_USE_ELF_REL=y
+# CONFIG_MTD is not set
+CONFIG_MULTI_IRQ_HANDLER=y
+CONFIG_MUTEX_SPIN_ON_OWNER=y
+CONFIG_NEED_DMA_MAP_STATE=y
+CONFIG_NEON=y
+CONFIG_NET_FLOW_LIMIT=y
+CONFIG_NET_PTP_CLASSIFY=y
+CONFIG_NET_VENDOR_ALLWINNER=y
+CONFIG_NLS=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NO_BOOTMEM=y
+CONFIG_NO_HZ=y
+CONFIG_NO_HZ_COMMON=y
+CONFIG_NO_HZ_IDLE=y
+CONFIG_NR_CPUS=8
+CONFIG_NVMEM=y
+CONFIG_NVMEM_SUNXI_SID=y
+CONFIG_OF=y
+CONFIG_OF_ADDRESS=y
+CONFIG_OF_EARLY_FLATTREE=y
+CONFIG_OF_FLATTREE=y
+CONFIG_OF_GPIO=y
+CONFIG_OF_IRQ=y
+CONFIG_OF_MDIO=y
+CONFIG_OF_NET=y
+CONFIG_OF_RESERVED_MEM=y
+CONFIG_OLD_SIGACTION=y
+CONFIG_OLD_SIGSUSPEND3=y
+CONFIG_OUTER_CACHE=y
+CONFIG_OUTER_CACHE_SYNC=y
+CONFIG_PADATA=y
+CONFIG_PAGE_OFFSET=0xC0000000
+# CONFIG_PARTITION_ADVANCED is not set
+# CONFIG_PCI_DOMAINS_GENERIC is not set
+# CONFIG_PCI_SYSCALL is not set
+CONFIG_PERF_EVENTS=y
+CONFIG_PERF_USE_VMALLOC=y
+CONFIG_PGTABLE_LEVELS=3
+CONFIG_PHYLIB=y
+CONFIG_PHYS_ADDR_T_64BIT=y
+CONFIG_PHY_SUN4I_USB=y
+CONFIG_PHY_SUN9I_USB=y
+CONFIG_PINCTRL=y
+# CONFIG_PINCTRL_SINGLE is not set
+CONFIG_PINCTRL_SUN4I_A10=y
+# CONFIG_PINCTRL_SUN50I_A64 is not set
+# CONFIG_PINCTRL_SUN50I_A64_R is not set
+# CONFIG_PINCTRL_SUN50I_H5 is not set
+CONFIG_PINCTRL_SUN5I=y
+CONFIG_PINCTRL_SUN6I_A31=y
+CONFIG_PINCTRL_SUN6I_A31_R=y
+CONFIG_PINCTRL_SUN8I_A23=y
+CONFIG_PINCTRL_SUN8I_A23_R=y
+CONFIG_PINCTRL_SUN8I_A33=y
+CONFIG_PINCTRL_SUN8I_A83T=y
+CONFIG_PINCTRL_SUN8I_A83T_R=y
+CONFIG_PINCTRL_SUN8I_H3=y
+CONFIG_PINCTRL_SUN8I_H3_R=y
+CONFIG_PINCTRL_SUN8I_V3S=y
+CONFIG_PINCTRL_SUN9I_A80=y
+CONFIG_PINCTRL_SUN9I_A80_R=y
+CONFIG_PINCTRL_SUNXI=y
+# CONFIG_PL310_ERRATA_588369 is not set
+# CONFIG_PL310_ERRATA_727915 is not set
+# CONFIG_PL310_ERRATA_753970 is not set
+# CONFIG_PL310_ERRATA_769419 is not set
+CONFIG_PM=y
+CONFIG_PM_CLK=y
+# CONFIG_PM_DEBUG is not set
+CONFIG_PM_OPP=y
+CONFIG_PM_SLEEP=y
+CONFIG_PM_SLEEP_SMP=y
+CONFIG_POWER_RESET=y
+CONFIG_POWER_SUPPLY=y
+CONFIG_PPS=y
+CONFIG_PREEMPT=y
+CONFIG_PREEMPT_COUNT=y
+# CONFIG_PREEMPT_NONE is not set
+CONFIG_PREEMPT_NOTIFIERS=y
+CONFIG_PREEMPT_RCU=y
+CONFIG_PRINTK_TIME=y
+CONFIG_PROC_EVENTS=y
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_PTP_1588_CLOCK=y
+CONFIG_PWM=y
+CONFIG_PWM_SUN4I=y
+CONFIG_PWM_SYSFS=y
+CONFIG_RATIONAL=y
+# CONFIG_RCU_BOOST is not set
+CONFIG_RCU_NEED_SEGCBLIST=y
+CONFIG_RCU_STALL_COMMON=y
+CONFIG_REGMAP=y
+CONFIG_REGMAP_I2C=y
+CONFIG_REGMAP_IRQ=y
+CONFIG_REGMAP_MMIO=y
+CONFIG_REGMAP_SPI=y
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_AXP20X=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
+CONFIG_REGULATOR_GPIO=y
+CONFIG_RELAY=y
+CONFIG_RESET_CONTROLLER=y
+CONFIG_RESET_SUNXI=y
+CONFIG_RFS_ACCEL=y
+CONFIG_RPS=y
+CONFIG_RWSEM_SPIN_ON_OWNER=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_SATA_PMP=y
+# CONFIG_SCHED_INFO is not set
+CONFIG_SCSI=y
+CONFIG_SDIO_UART=y
+CONFIG_SECURITYFS=y
+CONFIG_SERIAL_8250_DEPRECATED_OPTIONS=y
+CONFIG_SERIAL_8250_DW=y
+CONFIG_SERIAL_8250_FSL=y
+CONFIG_SERIAL_8250_NR_UARTS=8
+CONFIG_SERIAL_8250_RUNTIME_UARTS=8
+CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_SERIO=y
+CONFIG_SERIO_SERPORT=y
+CONFIG_SG_POOL=y
+CONFIG_SMP=y
+CONFIG_SMP_ON_UP=y
+CONFIG_SND=y
+CONFIG_SND_COMPRESS_OFFLOAD=y
+CONFIG_SND_JACK=y
+CONFIG_SND_JACK_INPUT_DEV=y
+CONFIG_SND_PCM=y
+CONFIG_SND_SOC=y
+CONFIG_SND_SOC_I2C_AND_SPI=y
+# CONFIG_SND_SUN4I_I2S is not set
+# CONFIG_SND_SUN4I_SPDIF is not set
+# CONFIG_SND_SUN8I_CODEC is not set
+# CONFIG_SND_SUN8I_CODEC_ANALOG is not set
+CONFIG_SOUND=y
+CONFIG_SOUND_OSS_CORE=y
+# CONFIG_SOUND_OSS_CORE_PRECLAIM is not set
+CONFIG_SPARSE_IRQ=y
+CONFIG_SPI=y
+CONFIG_SPI_MASTER=y
+CONFIG_SPI_SUN4I=y
+CONFIG_SPI_SUN6I=y
+CONFIG_SRCU=y
+CONFIG_STMMAC_ETH=y
+CONFIG_STMMAC_PLATFORM=y
+CONFIG_SUN4I_A10_CCU=y
+# CONFIG_SUN4I_EMAC is not set
+CONFIG_SUN4I_TIMER=y
+CONFIG_SUN5I_CCU=y
+CONFIG_SUN5I_HSTIMER=y
+CONFIG_SUN6I_A31_CCU=y
+CONFIG_SUN8I_A23_CCU=y
+CONFIG_SUN8I_A33_CCU=y
+CONFIG_SUN8I_A83T_CCU=y
+CONFIG_SUN8I_DE2_CCU=y
+CONFIG_SUN8I_H3_CCU=y
+CONFIG_SUN8I_R40_CCU=y
+CONFIG_SUN8I_R_CCU=y
+CONFIG_SUN8I_V3S_CCU=y
+CONFIG_SUN9I_A80_CCU=y
+CONFIG_SUNXI_CCU=y
+CONFIG_SUNXI_RSB=y
+CONFIG_SUNXI_SRAM=y
+CONFIG_SUNXI_WATCHDOG=y
+CONFIG_SUSPEND=y
+CONFIG_SUSPEND_FREEZER=y
+CONFIG_SWCONFIG=y
+CONFIG_SWCONFIG_B53=y
+# CONFIG_SWCONFIG_B53_MMAP_DRIVER is not set
+CONFIG_SWCONFIG_B53_PHY_DRIVER=y
+CONFIG_SWCONFIG_B53_PHY_FIXUP=y
+# CONFIG_SWCONFIG_B53_SRAB_DRIVER is not set
+CONFIG_SWIOTLB=y
+CONFIG_SWPHY=y
+CONFIG_SWP_EMULATE=y
+CONFIG_SYSFS_SYSCALL=y
+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+CONFIG_SYS_SUPPORTS_HUGETLBFS=y
+CONFIG_TASKS_RCU=y
+CONFIG_THERMAL=y
+CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y
+CONFIG_THERMAL_EMERGENCY_POWEROFF_DELAY_MS=0
+CONFIG_THERMAL_GOV_STEP_WISE=y
+CONFIG_THERMAL_HWMON=y
+CONFIG_THERMAL_OF=y
+# CONFIG_THUMB2_KERNEL is not set
+CONFIG_TICK_CPU_ACCOUNTING=y
+CONFIG_TIMER_OF=y
+CONFIG_TIMER_PROBE=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_TOUCHSCREEN_PROPERTIES=y
+CONFIG_TOUCHSCREEN_SUN4I=y
+CONFIG_TREE_SRCU=y
+CONFIG_UNCOMPRESS_INCLUDE="debug/uncompress.h"
+CONFIG_UNINLINE_SPIN_UNLOCK=y
+CONFIG_USB=y
+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
+CONFIG_USB_COMMON=y
+CONFIG_USB_DWC2=y
+CONFIG_USB_DWC2_HOST=y
+# CONFIG_USB_DWC2_TRACK_MISSED_SOFS is not set
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_HCD_PLATFORM=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_NET_DRIVERS=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_OHCI_HCD_PLATFORM=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_SUPPORT=y
+CONFIG_USERIO=y
+CONFIG_USE_OF=y
+CONFIG_VDSO=y
+CONFIG_VECTORS_BASE=0xffff0000
+CONFIG_VFAT_FS=y
+CONFIG_VFP=y
+CONFIG_VFPv3=y
+CONFIG_VHOST=y
+CONFIG_VHOST_NET=y
+CONFIG_VIRTUALIZATION=y
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_VT=y
+CONFIG_VT_CONSOLE=y
+CONFIG_VT_CONSOLE_SLEEP=y
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_WATCHDOG_CORE=y
+# CONFIG_WQ_POWER_EFFICIENT_DEFAULT is not set
+CONFIG_XPS=y
+CONFIG_XZ_DEC_ARM=y
+CONFIG_XZ_DEC_BCJ=y
+CONFIG_ZBOOT_ROM_BSS=0
+CONFIG_ZBOOT_ROM_TEXT=0
--- a/target/linux/sunxi/cortexa53/config-default
+++ b/target/linux/sunxi/cortexa53/config-default
@@ -0,0 +1,109 @@
+CONFIG_64BIT=y
+CONFIG_ARCH_DMA_ADDR_T_64BIT=y
+CONFIG_ARCH_HAS_CACHE_LINE_SIZE=y
+CONFIG_ARCH_HAS_FORTIFY_SOURCE=y
+CONFIG_ARCH_HAS_HOLES_MEMORYMODEL=y
+CONFIG_ARCH_HAS_KCOV=y
+CONFIG_ARCH_MMAP_RND_BITS=18
+CONFIG_ARCH_MMAP_RND_BITS_MAX=24
+CONFIG_ARCH_MMAP_RND_BITS_MIN=18
+CONFIG_ARCH_MMAP_RND_COMPAT_BITS_MIN=11
+# CONFIG_ARCH_OPTIONAL_KERNEL_RWX is not set
+# CONFIG_ARCH_OPTIONAL_KERNEL_RWX_DEFAULT is not set
+CONFIG_ARCH_PROC_KCORE_TEXT=y
+CONFIG_ARCH_SELECT_MEMORY_MODEL=y
+CONFIG_ARCH_SPARSEMEM_DEFAULT=y
+CONFIG_ARCH_SPARSEMEM_ENABLE=y
+CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
+CONFIG_ARCH_SUPPORTS_MEMORY_FAILURE=y
+CONFIG_ARCH_SUPPORTS_NUMA_BALANCING=y
+CONFIG_ARCH_WANT_COMPAT_IPC_PARSE_VERSION=y
+CONFIG_ARCH_WANT_FRAME_POINTERS=y
+CONFIG_ARCH_WANT_HUGE_PMD_SHARE=y
+CONFIG_ARM64=y
+# CONFIG_ARM64_16K_PAGES is not set
+CONFIG_ARM64_4K_PAGES=y
+# CONFIG_ARM64_64K_PAGES is not set
+CONFIG_ARM64_CONT_SHIFT=4
+# CONFIG_ARM64_CRYPTO is not set
+# CONFIG_ARM64_HW_AFDBM is not set
+# CONFIG_ARM64_LSE_ATOMICS is not set
+CONFIG_ARM64_PAGE_SHIFT=12
+# CONFIG_ARM64_PAN is not set
+# CONFIG_ARM64_PMEM is not set
+# CONFIG_ARM64_PTDUMP is not set
+# CONFIG_ARM64_PTDUMP_CORE is not set
+# CONFIG_ARM64_PTDUMP_DEBUGFS is not set
+# CONFIG_ARM64_RANDOMIZE_TEXT_OFFSET is not set
+CONFIG_ARM64_SSBD=y
+# CONFIG_ARM64_SW_TTBR0_PAN is not set
+# CONFIG_ARM64_UAO is not set
+CONFIG_ARM64_VA_BITS=39
+CONFIG_ARM64_VA_BITS_39=y
+# CONFIG_ARM64_VA_BITS_48 is not set
+# CONFIG_ARM64_VHE is not set
+CONFIG_ARM_AMBA=y
+CONFIG_ARM_GIC_V3=y
+# CONFIG_ARM_SP805_WATCHDOG is not set
+CONFIG_AUDIT_ARCH_COMPAT_GENERIC=y
+# CONFIG_COMMON_CLK_VERSATILE is not set
+CONFIG_COMMON_CLK_XGENE=y
+# CONFIG_COMPAT is not set
+# CONFIG_DEBUG_ALIGN_RODATA is not set
+CONFIG_DWMAC_SUN8I=y
+CONFIG_FRAME_POINTER=y
+# CONFIG_FSL_ERRATUM_A008585 is not set
+CONFIG_GENERIC_BUG_RELATIVE_POINTERS=y
+CONFIG_GENERIC_CSUM=y
+CONFIG_GENERIC_IRQ_MIGRATION=y
+CONFIG_HARDEN_BRANCH_PREDICTOR=y
+CONFIG_HAVE_ALIGNED_STRUCT_PAGE=y
+CONFIG_HAVE_ARCH_HUGE_VMAP=y
+CONFIG_HAVE_ARCH_KASAN=y
+CONFIG_HAVE_ARCH_VMAP_STACK=y
+CONFIG_HAVE_CMPXCHG_DOUBLE=y
+CONFIG_HAVE_CMPXCHG_LOCAL=y
+CONFIG_HAVE_DEBUG_BUGVERBOSE=y
+CONFIG_HAVE_MEMORY_PRESENT=y
+CONFIG_HAVE_PATA_PLATFORM=y
+CONFIG_ILLEGAL_POINTER_VALUE=0xdead000000000000
+CONFIG_KERNEL_MODE_NEON=y
+CONFIG_KVM_ARM_PMU=y
+CONFIG_MDIO_BUS_MUX=y
+CONFIG_MODULES_USE_ELF_RELA=y
+CONFIG_NEED_SG_DMA_LENGTH=y
+CONFIG_NO_IOPORT_MAP=y
+# CONFIG_NUMA is not set
+CONFIG_PARTITION_PERCPU=y
+# CONFIG_PCI_DOMAINS is not set
+# CONFIG_PHY_XGENE is not set
+# CONFIG_PINCTRL_SUN4I_A10 is not set
+CONFIG_PINCTRL_SUN50I_A64=y
+CONFIG_PINCTRL_SUN50I_A64_R=y
+CONFIG_PINCTRL_SUN50I_H5=y
+# CONFIG_PINCTRL_SUN5I is not set
+# CONFIG_PINCTRL_SUN6I_A31 is not set
+# CONFIG_PINCTRL_SUN6I_A31_R is not set
+# CONFIG_PINCTRL_SUN8I_A23 is not set
+# CONFIG_PINCTRL_SUN8I_A23_R is not set
+# CONFIG_PINCTRL_SUN8I_A33 is not set
+# CONFIG_PINCTRL_SUN8I_A83T is not set
+# CONFIG_PINCTRL_SUN8I_A83T_R is not set
+# CONFIG_PINCTRL_SUN8I_H3 is not set
+# CONFIG_PINCTRL_SUN8I_V3S is not set
+# CONFIG_PINCTRL_SUN9I_A80 is not set
+# CONFIG_PINCTRL_SUN9I_A80_R is not set
+# CONFIG_RANDOMIZE_BASE is not set
+CONFIG_REALTEK_PHY=y
+# CONFIG_SERIAL_AMBA_PL011 is not set
+CONFIG_SOUND_OSS_CORE_PRECLAIM=y
+CONFIG_SPARSEMEM=y
+CONFIG_SPARSEMEM_EXTREME=y
+CONFIG_SPARSEMEM_MANUAL=y
+CONFIG_SPARSEMEM_VMEMMAP=y
+CONFIG_SPARSEMEM_VMEMMAP_ENABLE=y
+CONFIG_SUN50I_A64_CCU=y
+CONFIG_SYSCTL_EXCEPTION_TRACE=y
+CONFIG_THREAD_INFO_IN_TASK=y
+CONFIG_UNMAP_KERNEL_AT_EL0=y
+CONFIG_VMAP_STACK=y
--- a/target/linux/sunxi/cortexa53/target.mk
+++ b/target/linux/sunxi/cortexa53/target.mk
@@ -0,0 +1,13 @@
+#
+# Copyright (C) 2017 Hauke Mehrtens
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+include $(TOPDIR)/rules.mk
+
+ARCH:=aarch64
+BOARDNAME:=Allwinner A64
+CPU_TYPE:=cortex-a53
+KERNELNAME:=Image dtbs
--- a/target/linux/sunxi/cortexa7/config-default
+++ b/target/linux/sunxi/cortexa7/config-default
@@ -0,0 +1,11 @@
+CONFIG_DWMAC_SUN8I=y
+CONFIG_HARDEN_BRANCH_PREDICTOR=y
+# CONFIG_MACH_SUN4I is not set
+# CONFIG_MACH_SUN5I is not set
+# CONFIG_PINCTRL_GR8 is not set
+CONFIG_PINCTRL_SUN4I_A10=y
+# CONFIG_PINCTRL_SUN5I_A10S is not set
+# CONFIG_PINCTRL_SUN5I_A13 is not set
+CONFIG_MDIO_BUS_MUX=y
+# CONFIG_PINCTRL_SUN5I is not set
+# CONFIG_SUN4I_A10_CCU is not set
--- a/target/linux/sunxi/cortexa7/target.mk
+++ b/target/linux/sunxi/cortexa7/target.mk
@@ -0,0 +1,12 @@
+#
+# Copyright (C) 2017 Hauke Mehrtens
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+include $(TOPDIR)/rules.mk
+
+BOARDNAME:=Allwinner A20/A3x
+CPU_TYPE:=cortex-a7
+CPU_SUBTYPE:=neon-vfpv4
--- a/target/linux/sunxi/cortexa8/config-default
+++ b/target/linux/sunxi/cortexa8/config-default
@@ -0,0 +1,22 @@
+# CONFIG_ARCH_PHYS_ADDR_T_64BIT is not set
+# CONFIG_ARM_ERRATA_643719 is not set
+# CONFIG_ARM_LPAE is not set
+CONFIG_HARDEN_BRANCH_PREDICTOR=y
+# CONFIG_MACH_SUN6I is not set
+# CONFIG_MACH_SUN7I is not set
+# CONFIG_MACH_SUN8I is not set
+# CONFIG_MACH_SUN9I is not set
+CONFIG_PGTABLE_LEVELS=2
+# CONFIG_PHYS_ADDR_T_64BIT is not set
+# CONFIG_PINCTRL_SUN6I_A31 is not set
+# CONFIG_PINCTRL_SUN6I_A31S is not set
+# CONFIG_PINCTRL_SUN6I_A31_R is not set
+# CONFIG_PINCTRL_SUN7I_A20 is not set
+# CONFIG_PINCTRL_SUN8I_A23 is not set
+# CONFIG_PINCTRL_SUN8I_A23_R is not set
+# CONFIG_PINCTRL_SUN8I_A33 is not set
+# CONFIG_PINCTRL_SUN8I_A83T is not set
+# CONFIG_PINCTRL_SUN8I_H3 is not set
+# CONFIG_PINCTRL_SUN8I_H3_R is not set
+# CONFIG_PINCTRL_SUN9I_A80 is not set
+# CONFIG_PINCTRL_SUN9I_A80_R is not set
--- a/target/linux/sunxi/cortexa8/target.mk
+++ b/target/linux/sunxi/cortexa8/target.mk
@@ -0,0 +1,12 @@
+#
+# Copyright (C) 2017 Hauke Mehrtens
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+include $(TOPDIR)/rules.mk
+
+BOARDNAME:=Allwinner A1x
+CPU_TYPE:=cortex-a8
+CPU_SUBTYPE:=vfpv3
--- a/target/linux/sunxi/image/Config.in
+++ b/target/linux/sunxi/image/Config.in
@@ -0,0 +1,5 @@
+config SUNXI_SD_BOOT_PARTSIZE
+	int "Boot (SD Card) filesystem partition size (in MB)"
+	depends on TARGET_sunxi
+	default 20
+
--- a/target/linux/sunxi/image/Makefile
+++ b/target/linux/sunxi/image/Makefile
@@ -0,0 +1,46 @@
+#
+# Copyright (C) 2013-2016 OpenWrt.org
+# Copyright (C) 2016 Yousong Zhou
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+include $(TOPDIR)/rules.mk
+include $(INCLUDE_DIR)/image.mk
+
+FAT32_BLOCK_SIZE=1024
+FAT32_BLOCKS=$(shell echo $$(($(CONFIG_SUNXI_SD_BOOT_PARTSIZE)*1024*1024/$(FAT32_BLOCK_SIZE))))
+
+KERNEL_LOADADDR:=0x40008000
+
+define Build/sunxi-sdcard
+	rm -f $@.boot
+	mkfs.fat $@.boot -C $(FAT32_BLOCKS)
+
+	mcopy -i $@.boot $(STAGING_DIR_IMAGE)/$(DEVICE_NAME)-boot.scr ::boot.scr
+	mcopy -i $@.boot $(DTS_DIR)/$(SUNXI_DTS).dtb ::dtb
+	mcopy -i $@.boot $(IMAGE_KERNEL) ::uImage
+	./gen_sunxi_sdcard_img.sh $@ \
+		$@.boot \
+		$(IMAGE_ROOTFS) \
+		$(CONFIG_SUNXI_SD_BOOT_PARTSIZE) \
+		$(CONFIG_TARGET_ROOTFS_PARTSIZE) \
+		$(STAGING_DIR_IMAGE)/$(DEVICE_NAME)-u-boot-with-spl.bin
+	rm -f $@.boot
+endef
+
+# why \x00\x00\x00\x00 for zImage-initramfs
+define Device/Default
+  PROFILES := Default
+  DEVICE_VARS := SUNXI_DTS SUNXI_UBOOT
+  KERNEL_NAME := zImage
+  KERNEL := kernel-bin | uImage none
+  IMAGES := sdcard.img.gz
+  IMAGE/sdcard.img.gz := sunxi-sdcard | append-metadata | gzip
+endef
+
+include cortex-a7.mk
+include cortex-a8.mk
+include cortex-a53.mk
+
+$(eval $(call BuildImage))
--- a/target/linux/sunxi/image/cortex-a53.mk
+++ b/target/linux/sunxi/image/cortex-a53.mk
@@ -0,0 +1,51 @@
+#
+# Copyright (C) 2013-2016 OpenWrt.org
+# Copyright (C) 2016 Yousong Zhou
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+ifeq ($(SUBTARGET),cortexa53)
+
+define Device/sun50i-h5-nanopi-neo-plus2
+  DEVICE_TITLE:=Nanopi NEO Plus2 (H5)
+  SUPPORTED_DEVICES:=nanopi-neo-plus2
+  SUNXI_DTS:=allwinner/sun50i-h5-nanopi-neo-plus2
+  KERNEL_NAME := Image
+  KERNEL := kernel-bin
+endef
+
+TARGET_DEVICES += sun50i-h5-nanopi-neo-plus2
+
+define Device/sun50i-a64-pine64-plus
+  DEVICE_TITLE:=Pine64 Plus A64
+  SUPPORTED_DEVICES:=pine64,pine64-plus
+  SUNXI_DTS:=allwinner/sun50i-a64-pine64-plus
+  KERNEL_NAME := Image
+  KERNEL := kernel-bin
+endef
+
+TARGET_DEVICES += sun50i-a64-pine64-plus
+
+define Device/sun50i-a64-sopine-baseboard
+  DEVICE_TITLE:=Pine64 Sopine
+  SUPPORTED_DEVICES:=pine64,sopine-baseboard
+  SUNXI_DTS:=allwinner/sun50i-a64-sopine-baseboard
+  KERNEL_NAME := Image
+  KERNEL := kernel-bin
+endef
+
+TARGET_DEVICES += sun50i-a64-sopine-baseboard
+
+
+define Device/sun50i-h5-orangepi-zero-plus
+  DEVICE_TITLE:=Xunlong Orange Pi Zero Plus
+  SUPPORTED_DEVICES:=xunlong,orangepi-zero-plus
+  SUNXI_DTS:=allwinner/sun50i-h5-orangepi-zero-plus
+  KERNEL_NAME := Image
+  KERNEL := kernel-bin
+endef
+
+TARGET_DEVICES += sun50i-h5-orangepi-zero-plus
+
+endif
--- a/target/linux/sunxi/image/cortex-a7.mk
+++ b/target/linux/sunxi/image/cortex-a7.mk
@@ -0,0 +1,180 @@
+#
+# Copyright (C) 2013-2016 OpenWrt.org
+# Copyright (C) 2016 Yousong Zhou
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+ifeq ($(SUBTARGET),cortexa7)
+
+define Device/sun7i-a20-olinuxino-lime
+  DEVICE_TITLE:=Olimex A20-OLinuXino-LIME
+  DEVICE_PACKAGES:=kmod-ata-core kmod-ata-sunxi kmod-rtc-sunxi
+  SUPPORTED_DEVICES:=olimex,a20-olinuxino-lime
+  SUNXI_DTS:=sun7i-a20-olinuxino-lime
+endef
+
+TARGET_DEVICES += sun7i-a20-olinuxino-lime
+
+
+define Device/sun7i-a20-olinuxino-lime2
+  DEVICE_TITLE:=Olimex A20-OLinuXino-LIME2
+  DEVICE_PACKAGES:=kmod-ata-core kmod-ata-sunxi kmod-rtc-sunxi kmod-usb-hid
+  SUPPORTED_DEVICES:=olimex,a20-olinuxino-lime2
+  SUNXI_DTS:=sun7i-a20-olinuxino-lime2
+endef
+
+TARGET_DEVICES += sun7i-a20-olinuxino-lime2
+
+
+define Device/sun7i-a20-olinuxino-lime2-emmc
+  DEVICE_TITLE:=Olimex A20-OLinuXino-LIME2-eMMC
+  DEVICE_PACKAGES:=kmod-ata-core kmod-ata-sunxi kmod-rtc-sunxi kmod-usb-hid
+  SUPPORTED_DEVICES:=olimex,a20-olinuxino-lime2-emmc
+  SUNXI_DTS:=sun7i-a20-olinuxino-lime2-emmc
+endef
+
+TARGET_DEVICES += sun7i-a20-olinuxino-lime2-emmc
+
+
+define Device/sun7i-a20-olinuxino-micro
+  DEVICE_TITLE:=Olimex A20-Olinuxino Micro
+  DEVICE_PACKAGES:=kmod-ata-core kmod-ata-sunxi kmod-sun4i-emac kmod-rtc-sunxi
+  SUPPORTED_DEVICES:=olimex,a20-olinuxino-micro
+  SUNXI_DTS:=sun7i-a20-olinuxino-micro
+endef
+
+TARGET_DEVICES += sun7i-a20-olinuxino-micro
+
+
+define Device/sun7i-a20-bananapi
+  DEVICE_TITLE:=LeMaker Banana Pi
+  DEVICE_PACKAGES:=kmod-rtc-sunxi kmod-ata-core kmod-ata-sunxi
+  SUPPORTED_DEVICES:=lemaker,bananapi
+  SUNXI_DTS:=sun7i-a20-bananapi
+endef
+
+TARGET_DEVICES += sun7i-a20-bananapi
+
+
+define Device/sun7i-a20-bananapro
+  DEVICE_TITLE:=LeMaker Banana Pro
+  DEVICE_PACKAGES:=kmod-rtc-sunxi kmod-ata-core kmod-ata-sunxi kmod-brcmfmac
+  SUPPORTED_DEVICES:=lemaker,bananapro
+  SUNXI_DTS:=sun7i-a20-bananapro
+endef
+
+TARGET_DEVICES += sun7i-a20-bananapro
+
+
+define Device/sun7i-a20-cubieboard2
+  DEVICE_TITLE:=Cubietech Cubieboard2
+  DEVICE_PACKAGES:=kmod-ata-core kmod-ata-sunxi kmod-sun4i-emac kmod-rtc-sunxi
+  SUPPORTED_DEVICES:=cubietech,cubieboard2
+  SUNXI_DTS:=sun7i-a20-cubieboard2
+endef
+
+TARGET_DEVICES += sun7i-a20-cubieboard2
+
+
+define Device/sun7i-a20-cubietruck
+  DEVICE_TITLE:=Cubietech Cubietruck
+  DEVICE_PACKAGES:=kmod-ata-core kmod-ata-sunxi kmod-rtc-sunxi kmod-brcmfmac
+  SUPPORTED_DEVICES:=cubietech,cubietruck
+  SUNXI_DTS:=sun7i-a20-cubietruck
+endef
+
+TARGET_DEVICES += sun7i-a20-cubietruck
+
+
+define Device/sun7i-a20-lamobo-r1
+  DEVICE_TITLE:=Lamobo R1
+  DEVICE_PACKAGES:=kmod-ata-sunxi kmod-rtl8192cu swconfig wpad-mini
+  SUPPORTED_DEVICES:=lamobo,lamobo-r1
+  SUNXI_DTS:=sun7i-a20-lamobo-r1
+endef
+
+TARGET_DEVICES += sun7i-a20-lamobo-r1
+
+
+define Device/sun6i-a31-m9
+  DEVICE_TITLE:=Mele M9 top set box
+  DEVICE_PACKAGES:=kmod-sun4i-emac kmod-rtc-sunxi kmod-rtl8192cu
+  SUPPORTED_DEVICES:=mele,m9
+  SUNXI_DTS:=sun6i-a31-m9
+endef
+
+TARGET_DEVICES += sun6i-a31-m9
+
+
+define Device/sun8i-h2-plus-orangepi-r1
+  DEVICE_TITLE:=Xunlong Orange Pi R1
+  DEVICE_PACKAGES:=kmod-rtc-sunxi kmod-usb-net kmod-usb-net-rtl8152
+  SUPPORTED_DEVICES:=xunlong,orangepi-r1
+  SUNXI_DTS:=sun8i-h2-plus-orangepi-r1
+endef
+
+TARGET_DEVICES += sun8i-h2-plus-orangepi-r1
+
+
+define Device/sun8i-h3-nanopi-m1-plus
+  DEVICE_TITLE:=FriendlyArm NanoPi M1 Plus
+  DEVICE_PACKAGES:=kmod-rtc-sunxi \
+	kmod-leds-gpio kmod-ledtrig-heartbeat \
+	kmod-brcmfmac brcmfmac-firmware-43430-sdio wpad-mini
+  SUPPORTED_DEVICES:=friendlyarm,nanopi-m1-plus
+  SUNXI_DTS:=sun8i-h3-nanopi-m1-plus
+endef
+
+TARGET_DEVICES += sun8i-h3-nanopi-m1-plus
+
+
+define Device/sun8i-h3-nanopi-neo
+  DEVICE_TITLE:=FriendlyARM NanoPi NEO
+  SUPPORTED_DEVICES:=friendlyarm,nanopi-neo
+  SUNXI_DTS:=sun8i-h3-nanopi-neo
+endef
+
+TARGET_DEVICES += sun8i-h3-nanopi-neo
+
+
+define Device/sun8i-h3-orangepi-pc
+  DEVICE_TITLE:=Xunlong Orange Pi PC
+  DEVICE_PACKAGES:=kmod-rtc-sunxi kmod-gpio-button-hotplug
+  SUPPORTED_DEVICES:=xunlong,orangepi-pc
+  SUNXI_DTS:=sun8i-h3-orangepi-pc
+endef
+
+TARGET_DEVICES += sun8i-h3-orangepi-pc
+
+
+define Device/sun8i-h3-orangepi-plus
+  DEVICE_TITLE:=Xunlong Orange Pi Plus
+  DEVICE_PACKAGES:=kmod-rtc-sunxi
+  SUPPORTED_DEVICES:=xunlong,orangepi-plus
+  SUNXI_DTS:=sun8i-h3-orangepi-plus
+endef
+
+TARGET_DEVICES += sun8i-h3-orangepi-plus
+
+define Device/sun8i-h3-orangepi-2
+  DEVICE_TITLE:=Xunlong Orange Pi 2
+  DEVICE_PACKAGES:=kmod-rtc-sunxi
+  SUPPORTED_DEVICES:=xunlong,orangepi-2
+  SUNXI_DTS:=sun8i-h3-orangepi-2
+endef
+
+TARGET_DEVICES += sun8i-h3-orangepi-2
+
+
+define Device/sun7i-a20-pcduino3
+  DEVICE_TITLE:=LinkSprite pcDuino3
+  DEVICE_PACKAGES:=kmod-sun4i-emac kmod-rtc-sunxi kmod-ata-core kmod-ata-sunxi kmod-rtl8xxxu rtl8188eu-firmware
+  SUPPORTED_DEVICES:=linksprite,pcduino3
+  SUNXI_DTS:=sun7i-a20-pcduino3
+endef
+
+TARGET_DEVICES += sun7i-a20-pcduino3
+
+endif
--- a/target/linux/sunxi/image/cortex-a8.mk
+++ b/target/linux/sunxi/image/cortex-a8.mk
@@ -0,0 +1,69 @@
+#
+# Copyright (C) 2013-2016 OpenWrt.org
+# Copyright (C) 2016 Yousong Zhou
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+ifeq ($(SUBTARGET),cortexa8)
+
+define Device/sun4i-a10-olinuxino-lime
+  DEVICE_TITLE:=Olimex A10-OLinuXino-LIME
+  DEVICE_PACKAGES:=kmod-ata-core kmod-ata-sunxi kmod-sun4i-emac kmod-rtc-sunxi
+  SUPPORTED_DEVICES:=olimex,a10-olinuxino-lime
+  SUNXI_DTS:=sun4i-a10-olinuxino-lime
+endef
+
+TARGET_DEVICES += sun4i-a10-olinuxino-lime
+
+
+define Device/sun5i-a13-olimex-som
+  DEVICE_TITLE:=Olimex A13 SOM
+  DEVICE_PACKAGES:=kmod-rtl8192cu
+  SUPPORTED_DEVICES:=olimex,a13-olinuxino
+  SUNXI_DTS:=sun5i-a13-olinuxino
+endef
+
+TARGET_DEVICES += sun5i-a13-olimex-som
+
+
+define Device/sun5i-a13-olinuxino
+  DEVICE_TITLE:=Olimex A13-Olinuxino
+  DEVICE_PACKAGES:=kmod-rtl8192cu
+  SUPPORTED_DEVICES:=olimex,a13-olinuxino
+  SUNXI_DTS:=sun5i-a13-olinuxino
+endef
+
+TARGET_DEVICES += sun5i-a13-olinuxino
+
+
+define Device/sun4i-a10-cubieboard
+  DEVICE_TITLE:=Cubietech Cubieboard
+  DEVICE_PACKAGES:=kmod-ata-core kmod-ata-sunxi kmod-sun4i-emac kmod-rtc-sunxi
+  SUPPORTED_DEVICES:=cubietech,a10-cubieboard
+  SUNXI_DTS:=sun4i-a10-cubieboard
+endef
+
+TARGET_DEVICES += sun4i-a10-cubieboard
+
+
+define Device/sun4i-a10-pcduino
+  DEVICE_TITLE:=LinkSprite pcDuino
+  DEVICE_PACKAGES:=kmod-sun4i-emac kmod-rtc-sunxi kmod-rtl8192cu
+  SUPPORTED_DEVICES:=linksprite,a10-pcduino
+  SUNXI_DTS:=sun4i-a10-pcduino
+endef
+
+TARGET_DEVICES += sun4i-a10-pcduino
+
+
+define Device/sun4i-a10-marsboard
+  DEVICE_TITLE:=HAOYU Electronics Marsboard A10
+  DEVICE_PACKAGES:=mod-ata-core kmod-ata-sunxi kmod-sun4i-emac kmod-rtc-sunxi sound-soc-sunxi
+  SUPPORTED_DEVICES:=marsboard,a10-marsboard
+  SUNXI_DTS:=sun4i-a10-marsboard
+endef
+
+TARGET_DEVICES += sun4i-a10-marsboard
+
+endif
--- a/target/linux/sunxi/image/gen_sunxi_sdcard_img.sh
+++ b/target/linux/sunxi/image/gen_sunxi_sdcard_img.sh
@@ -0,0 +1,34 @@
+#!/usr/bin/env bash
+#
+# Copyright (C) 2013 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+set -ex
+[ $# -eq 6 ] || {
+    echo "SYNTAX: $0 <file> <bootfs image> <rootfs image> <bootfs size> <rootfs size> <u-boot image>"
+    exit 1
+}
+
+OUTPUT="$1"
+BOOTFS="$2"
+ROOTFS="$3"
+BOOTFSSIZE="$4"
+ROOTFSSIZE="$5"
+UBOOT="$6"
+
+head=4
+sect=63
+
+set `ptgen -o $OUTPUT -h $head -s $sect -l 1024 -t c -p ${BOOTFSSIZE}M -t 83 -p ${ROOTFSSIZE}M`
+
+BOOTOFFSET="$(($1 / 512))"
+BOOTSIZE="$(($2 / 512))"
+ROOTFSOFFSET="$(($3 / 512))"
+ROOTFSSIZE="$(($4 / 512))"
+
+dd bs=1024 if="$UBOOT" of="$OUTPUT" seek=8 conv=notrunc
+dd bs=512 if="$BOOTFS" of="$OUTPUT" seek="$BOOTOFFSET" conv=notrunc
+dd bs=512 if="$ROOTFS" of="$OUTPUT" seek="$ROOTFSOFFSET" conv=notrunc
--- a/target/linux/sunxi/modules.mk
+++ b/target/linux/sunxi/modules.mk
@@ -0,0 +1,85 @@
+#
+# Copyright (C) 2013-2016 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+
+define KernelPackage/rtc-sunxi
+    SUBMENU:=$(OTHER_MENU)
+    TITLE:=Sunxi SoC built-in RTC support
+    DEPENDS:=@TARGET_sunxi
+    $(call AddDepends/rtc)
+    KCONFIG:= \
+	CONFIG_RTC_DRV_SUNXI \
+	CONFIG_RTC_CLASS=y
+    FILES:=$(LINUX_DIR)/drivers/rtc/rtc-sunxi.ko
+    AUTOLOAD:=$(call AutoLoad,50,rtc-sunxi)
+endef
+
+define KernelPackage/rtc-sunxi/description
+ Support for the AllWinner sunXi SoC's onboard RTC
+endef
+
+$(eval $(call KernelPackage,rtc-sunxi))
+
+define KernelPackage/sunxi-ir
+    SUBMENU:=$(OTHER_MENU)
+    TITLE:=Sunxi SoC built-in IR support (A20)
+    DEPENDS:=@TARGET_sunxi +kmod-input-core
+    $(call AddDepends/rtc)
+    KCONFIG:= \
+	CONFIG_MEDIA_SUPPORT=y \
+	CONFIG_MEDIA_RC_SUPPORT=y \
+	CONFIG_RC_DEVICES=y \
+	CONFIG_IR_SUNXI
+    FILES:=$(LINUX_DIR)/drivers/media/rc/sunxi-cir.ko
+    AUTOLOAD:=$(call AutoLoad,50,sunxi-cir)
+endef
+
+define KernelPackage/sunxi-ir/description
+ Support for the AllWinner sunXi SoC's onboard IR (A20)
+endef
+
+$(eval $(call KernelPackage,sunxi-ir))
+
+define KernelPackage/ata-sunxi
+    TITLE:=AllWinner sunXi AHCI SATA support
+    SUBMENU:=$(BLOCK_MENU)
+    DEPENDS:=@TARGET_sunxi +kmod-ata-ahci-platform +kmod-scsi-core
+    KCONFIG:=CONFIG_AHCI_SUNXI
+    FILES:=$(LINUX_DIR)/drivers/ata/ahci_sunxi.ko
+    AUTOLOAD:=$(call AutoLoad,41,ahci_sunxi,1)
+endef
+
+define KernelPackage/ata-sunxi/description
+ SATA support for the AllWinner sunXi SoC's onboard AHCI SATA
+endef
+
+$(eval $(call KernelPackage,ata-sunxi))
+
+define KernelPackage/sun4i-emac
+  SUBMENU:=$(NETWORK_DEVICES_MENU)
+  TITLE:=AllWinner EMAC Ethernet support
+  DEPENDS:=@TARGET_sunxi +kmod-of-mdio +kmod-libphy
+  KCONFIG:=CONFIG_SUN4I_EMAC
+  FILES:=$(LINUX_DIR)/drivers/net/ethernet/allwinner/sun4i-emac.ko
+  AUTOLOAD:=$(call AutoProbe,sun4i-emac)
+endef
+
+$(eval $(call KernelPackage,sun4i-emac))
+
+
+define KernelPackage/sound-soc-sunxi
+  TITLE:=AllWinner built-in SoC sound support
+  KCONFIG:=CONFIG_SND_SUN4I_CODEC
+  FILES:=$(LINUX_DIR)/sound/soc/sunxi/sun4i-codec.ko
+  AUTOLOAD:=$(call AutoLoad,65,sun4i-codec)
+  DEPENDS:=@TARGET_sunxi +kmod-sound-soc-core
+  $(call AddDepends/sound)
+endef
+
+define KernelPackage/sound-soc-sunxi/description
+  Kernel support for AllWinner built-in SoC audio
+endef
+
+$(eval $(call KernelPackage,sound-soc-sunxi))
--- a/target/linux/sunxi/patches-4.14/001-net-stmmac-snps-dwmac-mdio-MDIOs-are-automatically-r.patch
+++ b/target/linux/sunxi/patches-4.14/001-net-stmmac-snps-dwmac-mdio-MDIOs-are-automatically-r.patch
@@ -0,0 +1,33 @@
+From b5beecb580376cd8d959eb990abece6a748a3ce3 Mon Sep 17 00:00:00 2001
+From: Corentin Labbe <clabbe.montjoie@gmail.com>
+Date: Tue, 24 Oct 2017 19:57:12 +0200
+Subject: [PATCH] net: stmmac: snps, dwmac-mdio MDIOs are automatically
+ registered
+
+stmmac bindings docs said that its mdio node must have
+compatible = "snps,dwmac-mdio";
+Since dwmac-sun8i does not have any good reasons to not doing it, all
+their MDIO node must have it.
+
+Since these compatible is automatically registered, dwmac-sun8i compatible
+does not need to be in need_mdio_ids.
+
+Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
+Signed-off-by: David S. Miller <davem@davemloft.net>
+---
+ drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c | 4 ----
+ 1 file changed, 4 deletions(-)
+
+--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
+@@ -317,10 +317,6 @@ static int stmmac_dt_phy(struct plat_stm
+ 	bool mdio = true;
+ 	static const struct of_device_id need_mdio_ids[] = {
+ 		{ .compatible = "snps,dwc-qos-ethernet-4.10" },
+-		{ .compatible = "allwinner,sun8i-a83t-emac" },
+-		{ .compatible = "allwinner,sun8i-h3-emac" },
+-		{ .compatible = "allwinner,sun8i-v3s-emac" },
+-		{ .compatible = "allwinner,sun50i-a64-emac" },
+ 		{},
+ 	};
+ 
--- a/target/linux/sunxi/patches-4.14/002-net-stmmac-dwmac-sun8i-Handle-integrated-external-MD.patch
+++ b/target/linux/sunxi/patches-4.14/002-net-stmmac-dwmac-sun8i-Handle-integrated-external-MD.patch
@@ -0,0 +1,506 @@
+From 634db83b82658f4641d8026e340c6027cf74a6bb Mon Sep 17 00:00:00 2001
+From: Corentin Labbe <clabbe.montjoie@gmail.com>
+Date: Tue, 24 Oct 2017 19:57:13 +0200
+Subject: [PATCH] net: stmmac: dwmac-sun8i: Handle integrated/external MDIOs
+
+The Allwinner H3 SoC have two distinct MDIO bus, only one could be
+active at the same time.
+The selection of the active MDIO bus are done via some bits in the EMAC
+register of the system controller.
+
+This patch implement this MDIO switch via a custom MDIO-mux.
+
+Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
+Reviewed-by: Andrew Lunn <andrew@lunn.ch>
+Signed-off-by: David S. Miller <davem@davemloft.net>
+---
+ drivers/net/ethernet/stmicro/stmmac/Kconfig       |   1 +
+ drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c | 353 ++++++++++++++--------
+ 2 files changed, 224 insertions(+), 130 deletions(-)
+
+--- a/drivers/net/ethernet/stmicro/stmmac/Kconfig
+++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig
+@@ -159,6 +159,7 @@ config DWMAC_SUN8I
+ 	tristate "Allwinner sun8i GMAC support"
+ 	default ARCH_SUNXI
+ 	depends on OF && (ARCH_SUNXI || COMPILE_TEST)
+	select MDIO_BUS_MUX
+ 	---help---
+ 	  Support for Allwinner H3 A83T A64 EMAC ethernet controllers.
+ 
+--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
+@@ -17,6 +17,7 @@
+ #include <linux/clk.h>
+ #include <linux/io.h>
+ #include <linux/iopoll.h>
+#include <linux/mdio-mux.h>
+ #include <linux/mfd/syscon.h>
+ #include <linux/module.h>
+ #include <linux/of_device.h>
+@@ -41,14 +42,14 @@
+  *				This value is used for disabling properly EMAC
+  *				and used as a good starting value in case of the
+  *				boot process(uboot) leave some stuff.
+- * @internal_phy:		Does the MAC embed an internal PHY
+ * @soc_has_internal_phy:	Does the MAC embed an internal PHY
+  * @support_mii:		Does the MAC handle MII
+  * @support_rmii:		Does the MAC handle RMII
+  * @support_rgmii:		Does the MAC handle RGMII
+  */
+ struct emac_variant {
+ 	u32 default_syscon_value;
+-	int internal_phy;
+	bool soc_has_internal_phy;
+ 	bool support_mii;
+ 	bool support_rmii;
+ 	bool support_rgmii;
+@@ -61,7 +62,8 @@ struct emac_variant {
+  * @rst_ephy:	reference to the optional EPHY reset for the internal PHY
+  * @variant:	reference to the current board variant
+  * @regmap:	regmap for using the syscon
+- * @use_internal_phy: Does the current PHY choice imply using the internal PHY
+ * @internal_phy_powered: Does the internal PHY is enabled
+ * @mux_handle:	Internal pointer used by mdio-mux lib
+  */
+ struct sunxi_priv_data {
+ 	struct clk *tx_clk;
+@@ -70,12 +72,13 @@ struct sunxi_priv_data {
+ 	struct reset_control *rst_ephy;
+ 	const struct emac_variant *variant;
+ 	struct regmap *regmap;
+-	bool use_internal_phy;
+	bool internal_phy_powered;
+	void *mux_handle;
+ };
+ 
+ static const struct emac_variant emac_variant_h3 = {
+ 	.default_syscon_value = 0x58000,
+-	.internal_phy = PHY_INTERFACE_MODE_MII,
+	.soc_has_internal_phy = true,
+ 	.support_mii = true,
+ 	.support_rmii = true,
+ 	.support_rgmii = true
+@@ -83,20 +86,20 @@ static const struct emac_variant emac_va
+ 
+ static const struct emac_variant emac_variant_v3s = {
+ 	.default_syscon_value = 0x38000,
+-	.internal_phy = PHY_INTERFACE_MODE_MII,
+	.soc_has_internal_phy = true,
+ 	.support_mii = true
+ };
+ 
+ static const struct emac_variant emac_variant_a83t = {
+ 	.default_syscon_value = 0,
+-	.internal_phy = 0,
+	.soc_has_internal_phy = false,
+ 	.support_mii = true,
+ 	.support_rgmii = true
+ };
+ 
+ static const struct emac_variant emac_variant_a64 = {
+ 	.default_syscon_value = 0,
+-	.internal_phy = 0,
+	.soc_has_internal_phy = false,
+ 	.support_mii = true,
+ 	.support_rmii = true,
+ 	.support_rgmii = true
+@@ -195,6 +198,9 @@ static const struct emac_variant emac_va
+ #define H3_EPHY_LED_POL		BIT(17) /* 1: active low, 0: active high */
+ #define H3_EPHY_SHUTDOWN	BIT(16) /* 1: shutdown, 0: power up */
+ #define H3_EPHY_SELECT		BIT(15) /* 1: internal PHY, 0: external PHY */
+#define H3_EPHY_MUX_MASK	(H3_EPHY_SHUTDOWN | H3_EPHY_SELECT)
+#define DWMAC_SUN8I_MDIO_MUX_INTERNAL_ID	1
+#define DWMAC_SUN8I_MDIO_MUX_EXTERNAL_ID	2
+ 
+ /* H3/A64 specific bits */
+ #define SYSCON_RMII_EN		BIT(13) /* 1: enable RMII (overrides EPIT) */
+@@ -635,6 +641,159 @@ static int sun8i_dwmac_reset(struct stmm
+ 	return 0;
+ }
+ 
+/* Search in mdio-mux node for internal PHY node and get its clk/reset */
+static int get_ephy_nodes(struct stmmac_priv *priv)
+{
+	struct sunxi_priv_data *gmac = priv->plat->bsp_priv;
+	struct device_node *mdio_mux, *iphynode;
+	struct device_node *mdio_internal;
+	int ret;
+
+	mdio_mux = of_get_child_by_name(priv->device->of_node, "mdio-mux");
+	if (!mdio_mux) {
+		dev_err(priv->device, "Cannot get mdio-mux node\n");
+		return -ENODEV;
+	}
+
+	mdio_internal = of_find_compatible_node(mdio_mux, NULL,
+						"allwinner,sun8i-h3-mdio-internal");
+	if (!mdio_internal) {
+		dev_err(priv->device, "Cannot get internal_mdio node\n");
+		return -ENODEV;
+	}
+
+	/* Seek for internal PHY */
+	for_each_child_of_node(mdio_internal, iphynode) {
+		gmac->ephy_clk = of_clk_get(iphynode, 0);
+		if (IS_ERR(gmac->ephy_clk))
+			continue;
+		gmac->rst_ephy = of_reset_control_get_exclusive(iphynode, NULL);
+		if (IS_ERR(gmac->rst_ephy)) {
+			ret = PTR_ERR(gmac->rst_ephy);
+			if (ret == -EPROBE_DEFER)
+				return ret;
+			continue;
+		}
+		dev_info(priv->device, "Found internal PHY node\n");
+		return 0;
+	}
+	return -ENODEV;
+}
+
+static int sun8i_dwmac_power_internal_phy(struct stmmac_priv *priv)
+{
+	struct sunxi_priv_data *gmac = priv->plat->bsp_priv;
+	int ret;
+
+	if (gmac->internal_phy_powered) {
+		dev_warn(priv->device, "Internal PHY already powered\n");
+		return 0;
+	}
+
+	dev_info(priv->device, "Powering internal PHY\n");
+	ret = clk_prepare_enable(gmac->ephy_clk);
+	if (ret) {
+		dev_err(priv->device, "Cannot enable internal PHY\n");
+		return ret;
+	}
+
+	/* Make sure the EPHY is properly reseted, as U-Boot may leave
+	 * it at deasserted state, and thus it may fail to reset EMAC.
+	 */
+	reset_control_assert(gmac->rst_ephy);
+
+	ret = reset_control_deassert(gmac->rst_ephy);
+	if (ret) {
+		dev_err(priv->device, "Cannot deassert internal phy\n");
+		clk_disable_unprepare(gmac->ephy_clk);
+		return ret;
+	}
+
+	gmac->internal_phy_powered = true;
+
+	return 0;
+}
+
+static int sun8i_dwmac_unpower_internal_phy(struct sunxi_priv_data *gmac)
+{
+	if (!gmac->internal_phy_powered)
+		return 0;
+
+	clk_disable_unprepare(gmac->ephy_clk);
+	reset_control_assert(gmac->rst_ephy);
+	gmac->internal_phy_powered = false;
+	return 0;
+}
+
+/* MDIO multiplexing switch function
+ * This function is called by the mdio-mux layer when it thinks the mdio bus
+ * multiplexer needs to switch.
+ * 'current_child' is the current value of the mux register
+ * 'desired_child' is the value of the 'reg' property of the target child MDIO
+ * node.
+ * The first time this function is called, current_child == -1.
+ * If current_child == desired_child, then the mux is already set to the
+ * correct bus.
+ */
+static int mdio_mux_syscon_switch_fn(int current_child, int desired_child,
+				     void *data)
+{
+	struct stmmac_priv *priv = data;
+	struct sunxi_priv_data *gmac = priv->plat->bsp_priv;
+	u32 reg, val;
+	int ret = 0;
+	bool need_power_ephy = false;
+
+	if (current_child ^ desired_child) {
+		regmap_read(gmac->regmap, SYSCON_EMAC_REG, &reg);
+		switch (desired_child) {
+		case DWMAC_SUN8I_MDIO_MUX_INTERNAL_ID:
+			dev_info(priv->device, "Switch mux to internal PHY");
+			val = (reg & ~H3_EPHY_MUX_MASK) | H3_EPHY_SELECT;
+
+			need_power_ephy = true;
+			break;
+		case DWMAC_SUN8I_MDIO_MUX_EXTERNAL_ID:
+			dev_info(priv->device, "Switch mux to external PHY");
+			val = (reg & ~H3_EPHY_MUX_MASK) | H3_EPHY_SHUTDOWN;
+			need_power_ephy = false;
+			break;
+		default:
+			dev_err(priv->device, "Invalid child ID %x\n",
+				desired_child);
+			return -EINVAL;
+		}
+		regmap_write(gmac->regmap, SYSCON_EMAC_REG, val);
+		if (need_power_ephy) {
+			ret = sun8i_dwmac_power_internal_phy(priv);
+			if (ret)
+				return ret;
+		} else {
+			sun8i_dwmac_unpower_internal_phy(gmac);
+		}
+		/* After changing syscon value, the MAC need reset or it will
+		 * use the last value (and so the last PHY set).
+		 */
+		ret = sun8i_dwmac_reset(priv);
+	}
+	return ret;
+}
+
+static int sun8i_dwmac_register_mdio_mux(struct stmmac_priv *priv)
+{
+	int ret;
+	struct device_node *mdio_mux;
+	struct sunxi_priv_data *gmac = priv->plat->bsp_priv;
+
+	mdio_mux = of_get_child_by_name(priv->device->of_node, "mdio-mux");
+	if (!mdio_mux)
+		return -ENODEV;
+
+	ret = mdio_mux_init(priv->device, mdio_mux, mdio_mux_syscon_switch_fn,
+			    &gmac->mux_handle, priv, priv->mii);
+	return ret;
+}
+
+ static int sun8i_dwmac_set_syscon(struct stmmac_priv *priv)
+ {
+ 	struct sunxi_priv_data *gmac = priv->plat->bsp_priv;
+@@ -649,35 +808,25 @@ static int sun8i_dwmac_set_syscon(struct
+ 			 "Current syscon value is not the default %x (expect %x)\n",
+ 			 val, reg);
+ 
+-	if (gmac->variant->internal_phy) {
+-		if (!gmac->use_internal_phy) {
+-			/* switch to external PHY interface */
+-			reg &= ~H3_EPHY_SELECT;
+-		} else {
+-			reg |= H3_EPHY_SELECT;
+-			reg &= ~H3_EPHY_SHUTDOWN;
+-			dev_dbg(priv->device, "Select internal_phy %x\n", reg);
+-
+-			if (of_property_read_bool(priv->plat->phy_node,
+-						  "allwinner,leds-active-low"))
+-				reg |= H3_EPHY_LED_POL;
+-			else
+-				reg &= ~H3_EPHY_LED_POL;
+-
+-			/* Force EPHY xtal frequency to 24MHz. */
+-			reg |= H3_EPHY_CLK_SEL;
+-
+-			ret = of_mdio_parse_addr(priv->device,
+-						 priv->plat->phy_node);
+-			if (ret < 0) {
+-				dev_err(priv->device, "Could not parse MDIO addr\n");
+-				return ret;
+-			}
+-			/* of_mdio_parse_addr returns a valid (0 ~ 31) PHY
+-			 * address. No need to mask it again.
+-			 */
+-			reg |= ret << H3_EPHY_ADDR_SHIFT;
+	if (gmac->variant->soc_has_internal_phy) {
+		if (of_property_read_bool(priv->plat->phy_node,
+					  "allwinner,leds-active-low"))
+			reg |= H3_EPHY_LED_POL;
+		else
+			reg &= ~H3_EPHY_LED_POL;
+
+		/* Force EPHY xtal frequency to 24MHz. */
+		reg |= H3_EPHY_CLK_SEL;
+
+		ret = of_mdio_parse_addr(priv->device, priv->plat->phy_node);
+		if (ret < 0) {
+			dev_err(priv->device, "Could not parse MDIO addr\n");
+			return ret;
+ 		}
+		/* of_mdio_parse_addr returns a valid (0 ~ 31) PHY
+		 * address. No need to mask it again.
+		 */
+		reg |= 1 << H3_EPHY_ADDR_SHIFT;
+ 	}
+ 
+ 	if (!of_property_read_u32(node, "allwinner,tx-delay-ps", &val)) {
+@@ -750,81 +899,21 @@ static void sun8i_dwmac_unset_syscon(str
+ 	regmap_write(gmac->regmap, SYSCON_EMAC_REG, reg);
+ }
+ 
+-static int sun8i_dwmac_power_internal_phy(struct stmmac_priv *priv)
+static void sun8i_dwmac_exit(struct platform_device *pdev, void *priv)
+ {
+-	struct sunxi_priv_data *gmac = priv->plat->bsp_priv;
+-	int ret;
+-
+-	if (!gmac->use_internal_phy)
+-		return 0;
+	struct sunxi_priv_data *gmac = priv;
+ 
+-	ret = clk_prepare_enable(gmac->ephy_clk);
+-	if (ret) {
+-		dev_err(priv->device, "Cannot enable ephy\n");
+-		return ret;
+	if (gmac->variant->soc_has_internal_phy) {
+		/* sun8i_dwmac_exit could be called with mdiomux uninit */
+		if (gmac->mux_handle)
+			mdio_mux_uninit(gmac->mux_handle);
+		if (gmac->internal_phy_powered)
+			sun8i_dwmac_unpower_internal_phy(gmac);
+ 	}
+ 
+-	/* Make sure the EPHY is properly reseted, as U-Boot may leave
+-	 * it at deasserted state, and thus it may fail to reset EMAC.
+-	 */
+-	reset_control_assert(gmac->rst_ephy);
+-
+-	ret = reset_control_deassert(gmac->rst_ephy);
+-	if (ret) {
+-		dev_err(priv->device, "Cannot deassert ephy\n");
+-		clk_disable_unprepare(gmac->ephy_clk);
+-		return ret;
+-	}
+-
+-	return 0;
+-}
+-
+-static int sun8i_dwmac_unpower_internal_phy(struct sunxi_priv_data *gmac)
+-{
+-	if (!gmac->use_internal_phy)
+-		return 0;
+-
+-	clk_disable_unprepare(gmac->ephy_clk);
+-	reset_control_assert(gmac->rst_ephy);
+-	return 0;
+-}
+-
+-/* sun8i_power_phy() - Activate the PHY:
+- * In case of error, no need to call sun8i_unpower_phy(),
+- * it will be called anyway by sun8i_dwmac_exit()
+- */
+-static int sun8i_power_phy(struct stmmac_priv *priv)
+-{
+-	int ret;
+-
+-	ret = sun8i_dwmac_power_internal_phy(priv);
+-	if (ret)
+-		return ret;
+-
+-	ret = sun8i_dwmac_set_syscon(priv);
+-	if (ret)
+-		return ret;
+-
+-	/* After changing syscon value, the MAC need reset or it will use
+-	 * the last value (and so the last PHY set.
+-	 */
+-	ret = sun8i_dwmac_reset(priv);
+-	if (ret)
+-		return ret;
+-	return 0;
+-}
+-
+-static void sun8i_unpower_phy(struct sunxi_priv_data *gmac)
+-{
+ 	sun8i_dwmac_unset_syscon(gmac);
+-	sun8i_dwmac_unpower_internal_phy(gmac);
+-}
+-
+-static void sun8i_dwmac_exit(struct platform_device *pdev, void *priv)
+-{
+-	struct sunxi_priv_data *gmac = priv;
+ 
+-	sun8i_unpower_phy(gmac);
+	reset_control_put(gmac->rst_ephy);
+ 
+ 	clk_disable_unprepare(gmac->tx_clk);
+ 
+@@ -853,7 +942,7 @@ static struct mac_device_info *sun8i_dwm
+ 	if (!mac)
+ 		return NULL;
+ 
+-	ret = sun8i_power_phy(priv);
+	ret = sun8i_dwmac_set_syscon(priv);
+ 	if (ret)
+ 		return NULL;
+ 
+@@ -895,6 +984,8 @@ static int sun8i_dwmac_probe(struct plat
+ 	struct sunxi_priv_data *gmac;
+ 	struct device *dev = &pdev->dev;
+ 	int ret;
+	struct stmmac_priv *priv;
+	struct net_device *ndev;
+ 
+ 	ret = stmmac_get_platform_resources(pdev, &stmmac_res);
+ 	if (ret)
+@@ -938,29 +1029,6 @@ static int sun8i_dwmac_probe(struct plat
+ 	}
+ 
+ 	plat_dat->interface = of_get_phy_mode(dev->of_node);
+-	if (plat_dat->interface == gmac->variant->internal_phy) {
+-		dev_info(&pdev->dev, "Will use internal PHY\n");
+-		gmac->use_internal_phy = true;
+-		gmac->ephy_clk = of_clk_get(plat_dat->phy_node, 0);
+-		if (IS_ERR(gmac->ephy_clk)) {
+-			ret = PTR_ERR(gmac->ephy_clk);
+-			dev_err(&pdev->dev, "Cannot get EPHY clock: %d\n", ret);
+-			return -EINVAL;
+-		}
+-
+-		gmac->rst_ephy = of_reset_control_get(plat_dat->phy_node, NULL);
+-		if (IS_ERR(gmac->rst_ephy)) {
+-			ret = PTR_ERR(gmac->rst_ephy);
+-			if (ret == -EPROBE_DEFER)
+-				return ret;
+-			dev_err(&pdev->dev, "No EPHY reset control found %d\n",
+-				ret);
+-			return -EINVAL;
+-		}
+-	} else {
+-		dev_info(&pdev->dev, "Will use external PHY\n");
+-		gmac->use_internal_phy = false;
+-	}
+ 
+ 	/* platform data specifying hardware features and callbacks.
+ 	 * hardware features were copied from Allwinner drivers.
+@@ -979,9 +1047,34 @@ static int sun8i_dwmac_probe(struct plat
+ 
+ 	ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res);
+ 	if (ret)
+-		sun8i_dwmac_exit(pdev, plat_dat->bsp_priv);
+		goto dwmac_exit;
+
+	ndev = dev_get_drvdata(&pdev->dev);
+	priv = netdev_priv(ndev);
+	/* The mux must be registered after parent MDIO
+	 * so after stmmac_dvr_probe()
+	 */
+	if (gmac->variant->soc_has_internal_phy) {
+		ret = get_ephy_nodes(priv);
+		if (ret)
+			goto dwmac_exit;
+		ret = sun8i_dwmac_register_mdio_mux(priv);
+		if (ret) {
+			dev_err(&pdev->dev, "Failed to register mux\n");
+			goto dwmac_mux;
+		}
+	} else {
+		ret = sun8i_dwmac_reset(priv);
+		if (ret)
+			goto dwmac_exit;
+	}
+ 
+ 	return ret;
+dwmac_mux:
+	sun8i_dwmac_unset_syscon(gmac);
+dwmac_exit:
+	sun8i_dwmac_exit(pdev, plat_dat->bsp_priv);
+return ret;
+ }
+ 
+ static const struct of_device_id sun8i_dwmac_match[] = {
--- a/target/linux/sunxi/patches-4.14/003-net-stmmac-sun8i-Restore-the-compatibles.patch
+++ b/target/linux/sunxi/patches-4.14/003-net-stmmac-sun8i-Restore-the-compatibles.patch
@@ -0,0 +1,35 @@
+From a8ff8ccb45d37efa64476958fc5e9a8d9716b23b Mon Sep 17 00:00:00 2001
+From: Corentin Labbe <clabbe.montjoie@gmail.com>
+Date: Tue, 24 Oct 2017 19:57:14 +0200
+Subject: [PATCH] net: stmmac: sun8i: Restore the compatibles
+
+The original dwmac-sun8i DT bindings have some issue on how to handle
+integrated PHY and was reverted in last RC of 4.13.
+But now we have a solution so we need to get back that was reverted.
+
+This patch restore compatibles about dwmac-sun8i
+This reverts commit ad4540cc5aa3 ("net: stmmac: sun8i: Remove the compatibles")
+
+Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
+Signed-off-by: David S. Miller <davem@davemloft.net>
+---
+ drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c | 8 ++++++++
+ 1 file changed, 8 insertions(+)
+
+--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
+@@ -1078,6 +1078,14 @@ return ret;
+ }
+ 
+ static const struct of_device_id sun8i_dwmac_match[] = {
+	{ .compatible = "allwinner,sun8i-h3-emac",
+		.data = &emac_variant_h3 },
+	{ .compatible = "allwinner,sun8i-v3s-emac",
+		.data = &emac_variant_v3s },
+	{ .compatible = "allwinner,sun8i-a83t-emac",
+		.data = &emac_variant_a83t },
+	{ .compatible = "allwinner,sun50i-a64-emac",
+		.data = &emac_variant_a64 },
+ 	{ }
+ };
+ MODULE_DEVICE_TABLE(of, sun8i_dwmac_match);
--- a/target/linux/sunxi/patches-4.14/004-net-stmmac-dwmac-sun8i-fix-allwinner-leds-active-low.patch
+++ b/target/linux/sunxi/patches-4.14/004-net-stmmac-dwmac-sun8i-fix-allwinner-leds-active-low.patch
@@ -0,0 +1,29 @@
+From 1c08ac0c4bd8e9d66c4dde29bc496c3b430dd028 Mon Sep 17 00:00:00 2001
+From: Corentin Labbe <clabbe.montjoie@gmail.com>
+Date: Tue, 28 Nov 2017 17:48:22 +0100
+Subject: net: stmmac: dwmac-sun8i: fix allwinner,leds-active-low handling
+
+The driver expect "allwinner,leds-active-low" to be in PHY node, but
+the binding doc expect it to be in MAC node.
+
+Since all board DT use it also in MAC node, the driver need to search
+allwinner,leds-active-low in MAC node.
+
+Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
+Signed-off-by: David S. Miller <davem@davemloft.net>
+---
+ drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c | 3 +--
+ 1 file changed, 1 insertion(+), 2 deletions(-)
+
+--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
+@@ -809,8 +809,7 @@ static int sun8i_dwmac_set_syscon(struct
+ 			 val, reg);
+ 
+ 	if (gmac->variant->soc_has_internal_phy) {
+-		if (of_property_read_bool(priv->plat->phy_node,
+-					  "allwinner,leds-active-low"))
+		if (of_property_read_bool(node, "allwinner,leds-active-low"))
+ 			reg |= H3_EPHY_LED_POL;
+ 		else
+ 			reg &= ~H3_EPHY_LED_POL;
--- a/target/linux/sunxi/patches-4.14/020-ARM-dts-sunxi-Restore-EMAC-changes-boards.patch
+++ b/target/linux/sunxi/patches-4.14/020-ARM-dts-sunxi-Restore-EMAC-changes-boards.patch
@@ -0,0 +1,292 @@
+From 4904337fe34fa7fc529d6f4d9ee8b96fe7db310a Mon Sep 17 00:00:00 2001
+From: Corentin Labbe <clabbe.montjoie@gmail.com>
+Date: Tue, 31 Oct 2017 09:19:12 +0100
+Subject: [PATCH] ARM: dts: sunxi: Restore EMAC changes (boards)
+
+The original dwmac-sun8i DT bindings have some issue on how to handle
+integrated PHY and was reverted in last RC of 4.13.
+But now we have a solution so we need to get back that was reverted.
+
+This patch restore all boards DT about dwmac-sun8i
+This reverts partially commit fe45174b72ae ("arm: dts: sunxi: Revert EMAC changes")
+
+Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
+Acked-by: Florian Fainelli <f.fainelli@gmail.com>
+Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
+---
+ arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts |  9 +++++++
+ arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts   | 19 +++++++++++++++
+ arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts     | 29 +++++++++++++++++++++++
+ arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts         |  7 ++++++
+ arch/arm/boot/dts/sun8i-h3-orangepi-2.dts         |  8 +++++++
+ arch/arm/boot/dts/sun8i-h3-orangepi-one.dts       |  8 +++++++
+ arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dts   |  5 ++++
+ arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts        |  8 +++++++
+ arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts      | 22 +++++++++++++++++
+ arch/arm/boot/dts/sun8i-h3-orangepi-plus2e.dts    | 16 +++++++++++++
+ 10 files changed, 131 insertions(+)
+
+--- a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts
+++ b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts
+@@ -56,6 +56,8 @@
+ 
+ 	aliases {
+ 		serial0 = &uart0;
+		/* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
+		ethernet0 = &emac;
+ 		ethernet1 = &xr819;
+ 	};
+ 
+@@ -102,6 +104,13 @@
+ 	status = "okay";
+ };
+ 
+&emac {
+	phy-handle = <&int_mii_phy>;
+	phy-mode = "mii";
+	allwinner,leds-active-low;
+	status = "okay";
+};
+
+ &mmc0 {
+ 	pinctrl-names = "default";
+ 	pinctrl-0 = <&mmc0_pins_a>;
+--- a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts
+++ b/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts
+@@ -52,6 +52,7 @@
+ 	compatible = "sinovoip,bpi-m2-plus", "allwinner,sun8i-h3";
+ 
+ 	aliases {
+		ethernet0 = &emac;
+ 		serial0 = &uart0;
+ 		serial1 = &uart1;
+ 	};
+@@ -114,6 +115,24 @@
+ 	status = "okay";
+ };
+ 
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_rgmii_pins>;
+	phy-supply = <&reg_gmac_3v3>;
+	phy-handle = <&ext_rgmii_phy>;
+	phy-mode = "rgmii";
+
+	allwinner,leds-active-low;
+	status = "okay";
+};
+
+&external_mdio {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+ &ir {
+ 	pinctrl-names = "default";
+ 	pinctrl-0 = <&ir_pins_a>;
+--- a/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts
+++ b/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts
+@@ -45,6 +45,16 @@
+ / {
+ 	model = "FriendlyArm NanoPi M1 Plus";
+ 	compatible = "friendlyarm,nanopi-m1-plus", "allwinner,sun8i-h3";
+
+	reg_gmac_3v3: gmac-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "gmac-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <100000>;
+		enable-active-high;
+		gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
+	};
+ };
+ 
+ &ehci1 {
+@@ -55,6 +65,25 @@
+ 	status = "okay";
+ };
+ 
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_rgmii_pins>;
+	phy-supply = <&reg_gmac_3v3>;
+	phy-handle = <&ext_rgmii_phy>;
+	phy-mode = "rgmii";
+
+	allwinner,leds-active-low;
+
+	status = "okay";
+};
+
+&external_mdio {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <7>;
+	};
+};
+
+ &ohci1 {
+ 	status = "okay";
+ };
+--- a/arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts
+++ b/arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts
+@@ -46,3 +46,10 @@
+ 	model = "FriendlyARM NanoPi NEO";
+ 	compatible = "friendlyarm,nanopi-neo", "allwinner,sun8i-h3";
+ };
+
+&emac {
+	phy-handle = <&int_mii_phy>;
+	phy-mode = "mii";
+	allwinner,leds-active-low;
+	status = "okay";
+};
+--- a/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
+@@ -54,6 +54,7 @@
+ 	aliases {
+ 		serial0 = &uart0;
+ 		/* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
+		ethernet0 = &emac;
+ 		ethernet1 = &rtl8189;
+ 	};
+ 
+@@ -117,6 +118,13 @@
+ 	status = "okay";
+ };
+ 
+&emac {
+	phy-handle = <&int_mii_phy>;
+	phy-mode = "mii";
+	allwinner,leds-active-low;
+	status = "okay";
+};
+
+ &ir {
+ 	pinctrl-names = "default";
+ 	pinctrl-0 = <&ir_pins_a>;
+--- a/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts
+@@ -52,6 +52,7 @@
+ 	compatible = "xunlong,orangepi-one", "allwinner,sun8i-h3";
+ 
+ 	aliases {
+		ethernet0 = &emac;
+ 		serial0 = &uart0;
+ 	};
+ 
+@@ -97,6 +98,13 @@
+ 	status = "okay";
+ };
+ 
+&emac {
+	phy-handle = <&int_mii_phy>;
+	phy-mode = "mii";
+	allwinner,leds-active-low;
+	status = "okay";
+};
+
+ &mmc0 {
+ 	pinctrl-names = "default";
+ 	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+--- a/arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dts
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dts
+@@ -53,6 +53,11 @@
+ 	};
+ };
+ 
+&emac {
+	/* LEDs changed to active high on the plus */
+	/delete-property/ allwinner,leds-active-low;
+};
+
+ &mmc1 {
+ 	pinctrl-names = "default";
+ 	pinctrl-0 = <&mmc1_pins_a>;
+--- a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts
+@@ -52,6 +52,7 @@
+ 	compatible = "xunlong,orangepi-pc", "allwinner,sun8i-h3";
+ 
+ 	aliases {
+		ethernet0 = &emac;
+ 		serial0 = &uart0;
+ 	};
+ 
+@@ -113,6 +114,13 @@
+ 	status = "okay";
+ };
+ 
+&emac {
+	phy-handle = <&int_mii_phy>;
+	phy-mode = "mii";
+	allwinner,leds-active-low;
+	status = "okay";
+};
+
+ &ir {
+ 	pinctrl-names = "default";
+ 	pinctrl-0 = <&ir_pins_a>;
+--- a/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
+@@ -47,6 +47,10 @@
+ 	model = "Xunlong Orange Pi Plus / Plus 2";
+ 	compatible = "xunlong,orangepi-plus", "allwinner,sun8i-h3";
+ 
+	aliases {
+		ethernet0 = &emac;
+	};
+
+ 	reg_gmac_3v3: gmac-3v3 {
+ 		compatible = "regulator-fixed";
+ 		regulator-name = "gmac-3v3";
+@@ -74,6 +78,24 @@
+ 	status = "okay";
+ };
+ 
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_rgmii_pins>;
+	phy-supply = <&reg_gmac_3v3>;
+	phy-handle = <&ext_rgmii_phy>;
+	phy-mode = "rgmii";
+
+	allwinner,leds-active-low;
+	status = "okay";
+};
+
+&external_mdio {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+ &mmc2 {
+ 	pinctrl-names = "default";
+ 	pinctrl-0 = <&mmc2_8bit_pins>;
+--- a/arch/arm/boot/dts/sun8i-h3-orangepi-plus2e.dts
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-plus2e.dts
+@@ -61,3 +61,19 @@
+ 		gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */
+ 	};
+ };
+
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_rgmii_pins>;
+	phy-supply = <&reg_gmac_3v3>;
+	phy-handle = <&ext_rgmii_phy>;
+	phy-mode = "rgmii";
+	status = "okay";
+};
+
+&external_mdio {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
--- a/target/linux/sunxi/patches-4.14/021-arm-dts-sunxi-h3-h5-Restore-EMAC-changes.patch
+++ b/target/linux/sunxi/patches-4.14/021-arm-dts-sunxi-h3-h5-Restore-EMAC-changes.patch
@@ -0,0 +1,54 @@
+From 4b236a0fe51259ccde06aed046fe20bfe6e25dce Mon Sep 17 00:00:00 2001
+From: Corentin Labbe <clabbe.montjoie@gmail.com>
+Date: Tue, 31 Oct 2017 09:19:10 +0100
+Subject: [PATCH] arm: dts: sunxi: h3/h5: Restore EMAC changes
+
+The original dwmac-sun8i DT bindings have some issue on how to handle
+integrated PHY and was reverted in last RC of 4.13.
+But now we have a solution so we need to get back that was reverted.
+
+This patch restore sunxi-h3-h5.dtsi
+This reverts partially commit fe45174b72ae ("arm: dts: sunxi: Revert EMAC changes")
+
+Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
+Acked-by: Florian Fainelli <f.fainelli@gmail.com>
+Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
+---
+ arch/arm/boot/dts/sunxi-h3-h5.dtsi | 26 ++++++++++++++++++++++++++
+ 1 file changed, 26 insertions(+)
+
+--- a/arch/arm/boot/dts/sunxi-h3-h5.dtsi
+++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
+@@ -391,6 +391,32 @@
+ 			clocks = <&osc24M>;
+ 		};
+ 
+		emac: ethernet@1c30000 {
+			compatible = "allwinner,sun8i-h3-emac";
+			syscon = <&syscon>;
+			reg = <0x01c30000 0x10000>;
+			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+			resets = <&ccu RST_BUS_EMAC>;
+			reset-names = "stmmaceth";
+			clocks = <&ccu CLK_BUS_EMAC>;
+			clock-names = "stmmaceth";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			mdio: mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				int_mii_phy: ethernet-phy@1 {
+					compatible = "ethernet-phy-ieee802.3-c22";
+					reg = <1>;
+					clocks = <&ccu CLK_BUS_EPHY>;
+					resets = <&ccu RST_BUS_EPHY>;
+				};
+			};
+		};
+
+ 		spi0: spi@01c68000 {
+ 			compatible = "allwinner,sun8i-h3-spi";
+ 			reg = <0x01c68000 0x1000>;
--- a/target/linux/sunxi/patches-4.14/022-ARM-dts-sunxi-h3-h5-represent-the-mdio-switch-used-b.patch
+++ b/target/linux/sunxi/patches-4.14/022-ARM-dts-sunxi-h3-h5-represent-the-mdio-switch-used-b.patch
@@ -0,0 +1,59 @@
+From 776245ae02f63ba2b94596b892c597676e190e78 Mon Sep 17 00:00:00 2001
+From: Corentin Labbe <clabbe.montjoie@gmail.com>
+Date: Tue, 31 Oct 2017 09:19:11 +0100
+Subject: [PATCH] ARM: dts: sunxi: h3/h5: represent the mdio switch used by
+ sun8i-h3-emac
+
+Since dwmac-sun8i could use either an integrated PHY or an external PHY
+(which could be at same MDIO address), we need to represent this selection
+by a MDIO switch.
+
+Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
+Acked-by: Florian Fainelli <f.fainelli@gmail.com>
+Reviewed-by: Andrew Lunn <andrew@lunn.ch>
+Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
+---
+ arch/arm/boot/dts/sunxi-h3-h5.dtsi | 31 +++++++++++++++++++++++++++----
+ 1 file changed, 27 insertions(+), 4 deletions(-)
+
+--- a/arch/arm/boot/dts/sunxi-h3-h5.dtsi
+++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
+@@ -408,11 +408,34 @@
+ 			mdio: mdio {
+ 				#address-cells = <1>;
+ 				#size-cells = <0>;
+-				int_mii_phy: ethernet-phy@1 {
+-					compatible = "ethernet-phy-ieee802.3-c22";
+				compatible = "snps,dwmac-mdio";
+			};
+
+			mdio-mux {
+				compatible = "allwinner,sun8i-h3-mdio-mux";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				mdio-parent-bus = <&mdio>;
+				/* Only one MDIO is usable at the time */
+				internal_mdio: mdio@1 {
+					compatible = "allwinner,sun8i-h3-mdio-internal";
+ 					reg = <1>;
+-					clocks = <&ccu CLK_BUS_EPHY>;
+-					resets = <&ccu RST_BUS_EPHY>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					int_mii_phy: ethernet-phy@1 {
+						compatible = "ethernet-phy-ieee802.3-c22";
+						reg = <1>;
+						clocks = <&ccu CLK_BUS_EPHY>;
+						resets = <&ccu RST_BUS_EPHY>;
+					};
+				};
+
+				external_mdio: mdio@2 {
+					reg = <2>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+ 				};
+ 			};
+ 		};
--- a/target/linux/sunxi/patches-4.14/025-arm64-dts-allwinner-A64-Restore-EMAC-changes.patch
+++ b/target/linux/sunxi/patches-4.14/025-arm64-dts-allwinner-A64-Restore-EMAC-changes.patch
@@ -0,0 +1,184 @@
+From 94f442886711c6c4f4383a1c5a6994a788ba05d8 Mon Sep 17 00:00:00 2001
+From: Corentin Labbe <clabbe.montjoie@gmail.com>
+Date: Tue, 31 Oct 2017 09:19:13 +0100
+Subject: [PATCH] arm64: dts: allwinner: A64: Restore EMAC changes
+
+The original dwmac-sun8i DT bindings have some issue on how to handle
+integrated PHY and was reverted in last RC of 4.13.
+But now we have a solution so we need to get back that was reverted.
+
+This patch restore arm64 DT about dwmac-sun8i for A64
+This reverts commit 87e1f5e8bb4b ("arm64: dts: allwinner: Revert EMAC changes")
+
+Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
+Acked-by: Florian Fainelli <f.fainelli@gmail.com>
+Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
+---
+ .../boot/dts/allwinner/sun50i-a64-bananapi-m64.dts   | 16 ++++++++++++++++
+ .../boot/dts/allwinner/sun50i-a64-pine64-plus.dts    | 15 +++++++++++++++
+ arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts  | 17 +++++++++++++++++
+ .../dts/allwinner/sun50i-a64-sopine-baseboard.dts    | 16 ++++++++++++++++
+ arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi        | 20 ++++++++++++++++++++
+ 5 files changed, 84 insertions(+)
+
+--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
+@@ -51,6 +51,7 @@
+ 	compatible = "sinovoip,bananapi-m64", "allwinner,sun50i-a64";
+ 
+ 	aliases {
+		ethernet0 = &emac;
+ 		serial0 = &uart0;
+ 		serial1 = &uart1;
+ 	};
+@@ -69,6 +70,14 @@
+ 	status = "okay";
+ };
+ 
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>;
+	phy-mode = "rgmii";
+	phy-handle = <&ext_rgmii_phy>;
+	status = "okay";
+};
+
+ &i2c1 {
+ 	pinctrl-names = "default";
+ 	pinctrl-0 = <&i2c1_pins>;
+@@ -79,6 +88,13 @@
+ 	bias-pull-up;
+ };
+ 
+&mdio {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+ &mmc0 {
+ 	pinctrl-names = "default";
+ 	pinctrl-0 = <&mmc0_pins>;
+--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-plus.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-plus.dts
+@@ -48,3 +48,18 @@
+ 
+ 	/* TODO: Camera, touchscreen, etc. */
+ };
+
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>;
+	phy-mode = "rgmii";
+	phy-handle = <&ext_rgmii_phy>;
+	status = "okay";
+};
+
+&mdio {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
+@@ -51,6 +51,7 @@
+ 	compatible = "pine64,pine64", "allwinner,sun50i-a64";
+ 
+ 	aliases {
+		ethernet0 = &emac;
+ 		serial0 = &uart0;
+ 		serial1 = &uart1;
+ 		serial2 = &uart2;
+@@ -71,6 +72,15 @@
+ 	status = "okay";
+ };
+ 
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&rmii_pins>;
+	phy-mode = "rmii";
+	phy-handle = <&ext_rmii_phy1>;
+	status = "okay";
+
+};
+
+ &i2c1 {
+ 	pinctrl-names = "default";
+ 	pinctrl-0 = <&i2c1_pins>;
+@@ -81,6 +91,13 @@
+ 	bias-pull-up;
+ };
+ 
+&mdio {
+	ext_rmii_phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+ &mmc0 {
+ 	pinctrl-names = "default";
+ 	pinctrl-0 = <&mmc0_pins>;
+--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts
+@@ -53,6 +53,7 @@
+ 		     "allwinner,sun50i-a64";
+ 
+ 	aliases {
+		ethernet0 = &emac;
+ 		serial0 = &uart0;
+ 	};
+ 
+@@ -76,6 +77,21 @@
+ 	status = "okay";
+ };
+ 
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>;
+	phy-mode = "rgmii";
+	phy-handle = <&ext_rgmii_phy>;
+	status = "okay";
+};
+
+&mdio {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+ &mmc2 {
+ 	pinctrl-names = "default";
+ 	pinctrl-0 = <&mmc2_pins>;
+--- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
+@@ -450,6 +450,26 @@
+ 			#size-cells = <0>;
+ 		};
+ 
+		emac: ethernet@1c30000 {
+			compatible = "allwinner,sun50i-a64-emac";
+			syscon = <&syscon>;
+			reg = <0x01c30000 0x10000>;
+			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+			resets = <&ccu RST_BUS_EMAC>;
+			reset-names = "stmmaceth";
+			clocks = <&ccu CLK_BUS_EMAC>;
+			clock-names = "stmmaceth";
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			mdio: mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
+ 		gic: interrupt-controller@1c81000 {
+ 			compatible = "arm,gic-400";
+ 			reg = <0x01c81000 0x1000>,
--- a/target/linux/sunxi/patches-4.14/026-arm64-dts-allwinner-add-snps-dwmac-mdio-compatible-t.patch
+++ b/target/linux/sunxi/patches-4.14/026-arm64-dts-allwinner-add-snps-dwmac-mdio-compatible-t.patch
@@ -0,0 +1,28 @@
+From 16416084e06e1ebff51a9e7721a8cc4ccc186f28 Mon Sep 17 00:00:00 2001
+From: Corentin Labbe <clabbe.montjoie@gmail.com>
+Date: Tue, 31 Oct 2017 09:19:15 +0100
+Subject: [PATCH] arm64: dts: allwinner: add snps,dwmac-mdio compatible to
+ emac/mdio
+
+stmmac bindings docs said that its mdio node must have
+compatible = "snps,dwmac-mdio";
+Since dwmac-sun8i does not have any good reasons to not doing it, all
+their MDIO node must have it.
+
+Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
+Acked-by: Florian Fainelli <f.fainelli@gmail.com>
+Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
+---
+ arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 1 +
+ 1 file changed, 1 insertion(+)
+
+--- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
+@@ -465,6 +465,7 @@
+ 			#size-cells = <0>;
+ 
+ 			mdio: mdio {
+				compatible = "snps,dwmac-mdio";
+ 				#address-cells = <1>;
+ 				#size-cells = <0>;
+ 			};
--- a/target/linux/sunxi/patches-4.14/027-arm64-dts-allwinner-H5-Restore-EMAC-changes.patch
+++ b/target/linux/sunxi/patches-4.14/027-arm64-dts-allwinner-H5-Restore-EMAC-changes.patch
@@ -0,0 +1,120 @@
+From 44a94c7ef989317de81e3e7f84385be2bf1b5fe2 Mon Sep 17 00:00:00 2001
+From: Corentin Labbe <clabbe.montjoie@gmail.com>
+Date: Tue, 31 Oct 2017 09:19:14 +0100
+Subject: [PATCH] arm64: dts: allwinner: H5: Restore EMAC changes
+
+The original dwmac-sun8i DT bindings have some issue on how to handle
+integrated PHY and was reverted in last RC of 4.13.
+But now we have a solution so we need to get back that was reverted.
+
+This patch restore arm64 DT about dwmac-sun8i for H5
+This reverts a part of commit 87e1f5e8bb4b ("arm64: dts: allwinner: Revert EMAC changes")
+
+Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
+Acked-by: Florian Fainelli <f.fainelli@gmail.com>
+Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
+---
+ arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo2.dts | 17 +++++++++++++++++
+ .../arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts | 17 +++++++++++++++++
+ .../boot/dts/allwinner/sun50i-h5-orangepi-prime.dts     | 17 +++++++++++++++++
+ 3 files changed, 51 insertions(+)
+
+--- a/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo2.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo2.dts
+@@ -50,6 +50,7 @@
+ 	compatible = "friendlyarm,nanopi-neo2", "allwinner,sun50i-h5";
+ 
+ 	aliases {
+		ethernet0 = &emac;
+ 		serial0 = &uart0;
+ 	};
+ 
+@@ -108,6 +109,22 @@
+ 	status = "okay";
+ };
+ 
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_rgmii_pins>;
+	phy-supply = <&reg_gmac_3v3>;
+	phy-handle = <&ext_rgmii_phy>;
+	phy-mode = "rgmii";
+	status = "okay";
+};
+
+&external_mdio {
+	ext_rgmii_phy: ethernet-phy@7 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <7>;
+	};
+};
+
+ &mmc0 {
+ 	pinctrl-names = "default";
+ 	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+--- a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
+@@ -59,6 +59,7 @@
+ 	};
+ 
+ 	aliases {
+		ethernet0 = &emac;
+ 		serial0 = &uart0;
+ 	};
+ 
+@@ -136,6 +137,22 @@
+ 	status = "okay";
+ };
+ 
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_rgmii_pins>;
+	phy-supply = <&reg_gmac_3v3>;
+	phy-handle = <&ext_rgmii_phy>;
+	phy-mode = "rgmii";
+	status = "okay";
+};
+
+&external_mdio {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+ &ir {
+ 	pinctrl-names = "default";
+ 	pinctrl-0 = <&ir_pins_a>;
+--- a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts
+@@ -54,6 +54,7 @@
+ 	compatible = "xunlong,orangepi-prime", "allwinner,sun50i-h5";
+ 
+ 	aliases {
+		ethernet0 = &emac;
+ 		serial0 = &uart0;
+ 	};
+ 
+@@ -143,6 +144,22 @@
+ 	status = "okay";
+ };
+ 
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_rgmii_pins>;
+	phy-supply = <&reg_gmac_3v3>;
+	phy-handle = <&ext_rgmii_phy>;
+	phy-mode = "rgmii";
+	status = "okay";
+};
+
+&external_mdio {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+ &ir {
+ 	pinctrl-names = "default";
+ 	pinctrl-0 = <&ir_pins_a>;
--- a/target/linux/sunxi/patches-4.14/030-arm64-allwinner-a64-add-Ethernet-PHY-regulator-for-s.patch
+++ b/target/linux/sunxi/patches-4.14/030-arm64-allwinner-a64-add-Ethernet-PHY-regulator-for-s.patch
@@ -0,0 +1,51 @@
+From bdfe4cebea11476d278b1b98dd0f7cdac8269d62 Mon Sep 17 00:00:00 2001
+From: Icenowy Zheng <icenowy@aosc.io>
+Date: Fri, 10 Nov 2017 17:26:54 +0800
+Subject: [PATCH] arm64: allwinner: a64: add Ethernet PHY regulator for several
+ boards
+
+On several A64 boards the Ethernet PHY is powered by the DC1SW regulator
+on the AXP803 PMIC.
+
+Add phy-handle property to these boards' emac node.
+
+Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
+Acked-by: Corentin LABBE <clabbe.montjoie@gmail.com>
+Tested-by: Corentin LABBE <clabbe.montjoie@gmail.com>
+Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
+---
+ arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts     | 1 +
+ arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts           | 1 +
+ arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts | 1 +
+ 3 files changed, 3 insertions(+)
+
+--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
+@@ -75,6 +75,7 @@
+ 	pinctrl-0 = <&rgmii_pins>;
+ 	phy-mode = "rgmii";
+ 	phy-handle = <&ext_rgmii_phy>;
+	phy-supply = <&reg_dc1sw>;
+ 	status = "okay";
+ };
+ 
+--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
+@@ -77,6 +77,7 @@
+ 	pinctrl-0 = <&rmii_pins>;
+ 	phy-mode = "rmii";
+ 	phy-handle = <&ext_rmii_phy1>;
+	phy-supply = <&reg_dc1sw>;
+ 	status = "okay";
+ 
+ };
+--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts
+@@ -82,6 +82,7 @@
+ 	pinctrl-0 = <&rgmii_pins>;
+ 	phy-mode = "rgmii";
+ 	phy-handle = <&ext_rgmii_phy>;
+	phy-supply = <&reg_dc1sw>;
+ 	status = "okay";
+ };
+ 
--- a/target/linux/sunxi/patches-4.14/060-ARM-dts-sun8i-add-support-for-Orange-Pi-R1.patch
+++ b/target/linux/sunxi/patches-4.14/060-ARM-dts-sun8i-add-support-for-Orange-Pi-R1.patch
@@ -0,0 +1,105 @@
+From 74942cd5dfe4ac4fd982fe58118bc69346a2bd18 Mon Sep 17 00:00:00 2001
+From: Icenowy Zheng <icenowy@aosc.io>
+Date: Sun, 12 Nov 2017 20:41:29 +0800
+Subject: [PATCH] ARM: dts: sun8i: add support for Orange Pi R1
+
+Orange Pi R1 is a board design based on Orange Pi Zero, with XR819 Wi-Fi
+chip replaced by RTL8189ETV Wi-Fi module and the USB Type-A jack
+replaced by an onboard USB RTL8152B USB-Ethernet adapter.
+
+Add support for it.
+
+Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
+Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
+---
+ arch/arm/boot/dts/Makefile                      |  1 +
+ arch/arm/boot/dts/sun8i-h2-plus-orangepi-r1.dts | 73 +++++++++++++++++++++++++
+ 2 files changed, 74 insertions(+)
+ create mode 100644 arch/arm/boot/dts/sun8i-h2-plus-orangepi-r1.dts
+
+--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
+@@ -916,6 +916,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
+ 	sun8i-a83t-allwinner-h8homlet-v2.dtb \
+ 	sun8i-a83t-bananapi-m3.dtb \
+ 	sun8i-a83t-cubietruck-plus.dtb \
+	sun8i-h2-plus-orangepi-r1.dtb \
+ 	sun8i-h2-plus-orangepi-zero.dtb \
+ 	sun8i-h3-bananapi-m2-plus.dtb \
+ 	sun8i-h3-beelink-x2.dtb \
+--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-r1.dts
+@@ -0,0 +1,73 @@
+/*
+ * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.xyz>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/* Orange Pi R1 is based on Orange Pi Zero design */
+#include "sun8i-h2-plus-orangepi-zero.dts"
+
+/ {
+	model = "Xunlong Orange Pi R1";
+	compatible = "xunlong,orangepi-r1", "allwinner,sun8i-h2-plus";
+
+	/delete-node/ reg_vcc_wifi;
+
+	aliases {
+		ethernet1 = &rtl8189etv;
+	};
+};
+
+&ohci1 {
+	/*
+	 * RTL8152B USB-Ethernet adapter is connected to USB1,
+	 * and it's a USB 2.0 device. So the OHCI1 controller
+	 * can be left disabled.
+	 */
+	status = "disabled";
+};
+
+&mmc1 {
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+
+	rtl8189etv: sdio_wifi@1 {
+		reg = <1>;
+	};
+};
--- a/target/linux/sunxi/patches-4.14/061-arm-dts-sun50i-support-for-nanopi-neo-plus2-board.patch
+++ b/target/linux/sunxi/patches-4.14/061-arm-dts-sun50i-support-for-nanopi-neo-plus2-board.patch
@@ -0,0 +1,242 @@
+From 54cc3330c2334a0cea8cafc105a29c5d67f9fd32 Mon Sep 17 00:00:00 2001
+From: Antony Antony <antony@phenome.org>
+Date: Fri, 2 Mar 2018 10:50:48 +0100
+Subject: [PATCH] arm64: allwinner: h5: add NanoPi NEO Plus2 DT support
+
+Add initial DT for NanoPi NEO Plus2 by FriendlyARM
+- Allwinner quad core H5 Cortex A53 with an ARM Mali-450MP GPU
+- 1 GB DDR3 RAM
+- 8GB eMMC flash (Samsung KLM8G1WEPD-B031)
+- micro SD card slot
+- Gigabit Ethernet (external RTL8211E-VB-CG chip)
+- 802.11 b/g/n WiFi, Bluetooth 4.0 (Ampak AP6212A module)
+- 2x USB 2.0 host ports & 2x USB via headers
+
+Kernel 4.15 commit d7341305863b
+Kernel 4.16 commit 27d7f9297027
+
+Signed-off-by: Antony Antony <antony@phenome.org>
+
+--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
+@@ -9,6 +9,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-or
+ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-prime.dtb
+ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus2.dtb
+ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-nanopi-neo2.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-nanopi-neo-plus2.dtb
+ 
+ always		:= $(dtb-y)
+ subdir-y	:= $(dts-dirs)
+--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo-plus2.dts
+@@ -0,0 +1,210 @@
+/*
+ * Copyright (C) 2017 Antony Antony <antony@phenome.org>
+ * Copyright (C) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun50i-h5.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+	model = "FriendlyARM NanoPi NEO Plus2";
+	compatible = "friendlyarm,nanopi-neo-plus2", "allwinner,sun50i-h5";
+
+	aliases {
+		ethernet0 = &emac;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		pwr {
+			label = "nanopi:green:pwr";
+			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+
+		status {
+			label = "nanopi:red:status";
+			gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	reg_gmac_3v3: gmac-3v3 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		regulator-name = "gmac-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <100000>;
+		enable-active-high;
+		gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_vcc3v3: vcc3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vdd_cpux: gpio-regulator {
+		compatible = "regulator-gpio";
+		pinctrl-names = "default";
+		regulator-name = "vdd-cpux";
+		regulator-type = "voltage";
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1300000>;
+		regulator-ramp-delay = <50>; /* 4ms */
+		gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>;
+		gpios-states = <0x1>;
+		states = <1100000 0x0
+			  1300000 0x1>;
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+		post-power-on-delay-ms = <200>;
+	};
+};
+
+&codec {
+	allwinner,audio-routing =
+		"Line Out", "LINEOUT",
+		"MIC1", "Mic",
+		"Mic",  "MBIAS";
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci3 {
+	status = "okay";
+};
+
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_rgmii_pins>;
+	phy-supply = <&reg_gmac_3v3>;
+	phy-handle = <&ext_rgmii_phy>;
+	phy-mode = "rgmii";
+	status = "okay";
+};
+
+&external_mdio {
+	ext_rgmii_phy: ethernet-phy@7 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <7>;
+	};
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+	status = "okay";
+};
+
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins_a>;
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_8bit_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci3 {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usbphy {
+	/* USB Type-A ports' VBUS is always on */
+	status = "okay";
+};
--- a/target/linux/sunxi/patches-4.14/115-musb-ignore-vbus-errors.patch
+++ b/target/linux/sunxi/patches-4.14/115-musb-ignore-vbus-errors.patch
@@ -0,0 +1,26 @@
+From fce20ac5d8c98f1a8ea5298051d9fa669e455f04 Mon Sep 17 00:00:00 2001
+From: Hans de Goede <hdegoede@redhat.com>
+Date: Tue, 4 Aug 2015 23:22:45 +0200
+Subject: [PATCH] musb: sunxi: Ignore VBus errors in host-only mode
+
+For some unclear reason sometimes we get VBus errors in host-only mode,
+even though we do not have any vbus-detection then. Ignore these.
+
+Signed-off-by: Hans de Goede <hdegoede@redhat.com>
+---
+ drivers/usb/musb/sunxi.c | 4 ++++
+ 1 file changed, 4 insertions(+)
+
+--- a/drivers/usb/musb/sunxi.c
+++ b/drivers/usb/musb/sunxi.c
+@@ -192,6 +192,10 @@ static irqreturn_t sunxi_musb_interrupt(
+ 		musb_writeb(musb->mregs, MUSB_FADDR, 0);
+ 	}
+ 
+	/*  Ignore Vbus errors when in host only mode */
+	if (musb->port_mode == MUSB_PORT_MODE_HOST)
+		musb->int_usb &= ~MUSB_INTR_VBUSERROR;
+
+ 	musb->int_tx = readw(musb->mregs + SUNXI_MUSB_INTRTX);
+ 	if (musb->int_tx)
+ 		writew(musb->int_tx, musb->mregs + SUNXI_MUSB_INTRTX);
--- a/target/linux/sunxi/patches-4.14/131-reset-add-h3-resets.patch
+++ b/target/linux/sunxi/patches-4.14/131-reset-add-h3-resets.patch
@@ -0,0 +1,92 @@
+From 5f0bb9d0bc545ef53a83f7bd176fdc0736eed8e5 Mon Sep 17 00:00:00 2001
+From: Jens Kuske <jenskuske@gmail.com>
+Date: Tue, 27 Oct 2015 17:50:24 +0100
+Subject: [PATCH] reset: sunxi: Add Allwinner H3 bus resets
+
+The H3 bus resets have some holes between the registers, so we add
+an of_xlate() function to skip them according to the datasheet.
+
+Signed-off-by: Jens Kuske <jenskuske@gmail.com>
+---
+ .../bindings/reset/allwinner,sunxi-clock-reset.txt |  1 +
+ drivers/reset/reset-sunxi.c                        | 30 +++++++++++++++++++---
+ 2 files changed, 28 insertions(+), 3 deletions(-)
+
+--- a/Documentation/devicetree/bindings/reset/allwinner,sunxi-clock-reset.txt
+++ b/Documentation/devicetree/bindings/reset/allwinner,sunxi-clock-reset.txt
+@@ -8,6 +8,7 @@ Required properties:
+ - compatible: Should be one of the following:
+   "allwinner,sun6i-a31-ahb1-reset"
+   "allwinner,sun6i-a31-clock-reset"
+  "allwinner,sun8i-h3-bus-reset"
+ - reg: should be register base and length as documented in the
+   datasheet
+ - #reset-cells: 1, see below
+--- a/drivers/reset/reset-sunxi.c
+++ b/drivers/reset/reset-sunxi.c
+@@ -77,7 +77,9 @@ static const struct reset_control_ops su
+ 	.deassert	= sunxi_reset_deassert,
+ };
+ 
+-static int sunxi_reset_init(struct device_node *np)
+static int sunxi_reset_init(struct device_node *np,
+			    int (*of_xlate)(struct reset_controller_dev *rcdev,
+				    const struct of_phandle_args *reset_spec))
+ {
+ 	struct sunxi_reset_data *data;
+ 	struct resource res;
+@@ -110,6 +112,7 @@ static int sunxi_reset_init(struct devic
+ 	data->rcdev.nr_resets = size * 8;
+ 	data->rcdev.ops = &sunxi_reset_ops;
+ 	data->rcdev.of_node = np;
+	data->rcdev.of_xlate = of_xlate;
+ 
+ 	return reset_controller_register(&data->rcdev);
+ 
+@@ -118,6 +121,21 @@ err_alloc:
+ 	return ret;
+ };
+ 
+static int sun8i_h3_bus_reset_xlate(struct reset_controller_dev *rcdev,
+				    const struct of_phandle_args *reset_spec)
+{
+	unsigned int index = reset_spec->args[0];
+
+	if (index < 96)
+		return index;
+	else if (index < 128)
+		return index + 32;
+	else if (index < 160)
+		return index + 64;
+	else
+		return -EINVAL;
+}
+
+ /*
+  * These are the reset controller we need to initialize early on in
+  * our system, before we can even think of using a regular device
+@@ -125,15 +143,21 @@ err_alloc:
+  */
+ static const struct of_device_id sunxi_early_reset_dt_ids[] __initconst = {
+ 	{ .compatible = "allwinner,sun6i-a31-ahb1-reset", },
+	{ .compatible = "allwinner,sun8i-h3-bus-reset", .data = sun8i_h3_bus_reset_xlate, },
+ 	{ /* sentinel */ },
+ };
+ 
+ void __init sun6i_reset_init(void)
+ {
+ 	struct device_node *np;
+-
+-	for_each_matching_node(np, sunxi_early_reset_dt_ids)
+-		sunxi_reset_init(np);
+	const struct of_device_id *match;
+	int (*of_xlate)(struct reset_controller_dev *rcdev,
+			const struct of_phandle_args *reset_spec);
+
+	for_each_matching_node_and_match(np, sunxi_early_reset_dt_ids, &match) {
+		of_xlate = match->data;
+		sunxi_reset_init(np, of_xlate);
+	}
+ }
+ 
+ /*
--- a/target/linux/sunxi/patches-4.14/201-ARM-dts-sun8i-fix-USB-Ethernet-of-Orange-Pi-R1.patch
+++ b/target/linux/sunxi/patches-4.14/201-ARM-dts-sun8i-fix-USB-Ethernet-of-Orange-Pi-R1.patch
@@ -0,0 +1,48 @@
+From b76dc5927f6442df913f03ed261c5bff18a98df6 Mon Sep 17 00:00:00 2001
+From: Icenowy Zheng <icenowy@aosc.io>
+Date: Thu, 28 Dec 2017 21:01:56 +0800
+Subject: [PATCH] ARM: dts: sun8i: fix USB Ethernet of Orange Pi R1
+
+Orange Pi R1 uses a Realtek RTL8152B USB Ethernet chip, which is easily
+seen on the board but not show in the schematics. A regulator for the
+power of the RTL8152B chip is hidden, which uses the same pin with the
+Wi-Fi regulator on the original Orange Pi Zero.
+
+Add this regulator back to the device tree, and bind it to USB1.
+
+Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
+---
+ arch/arm/boot/dts/sun8i-h2-plus-orangepi-r1.dts | 18 ++++++++++++++++++
+ 1 file changed, 18 insertions(+)
+
+--- a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-r1.dts
+++ b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-r1.dts
+@@ -49,6 +49,20 @@
+ 
+ 	/delete-node/ reg_vcc_wifi;
+ 
+	/*
+	 * Ths pin of this regulator is the same with the Wi-Fi extra
+	 * regulator on the original Zero. However it's used for USB
+	 * Ethernet rather than the Wi-Fi now.
+	 */
+	reg_vcc_usb_eth: reg-vcc-usb-ethernet {
+		compatible = "regulator-fixed";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-name = "vcc-usb-ethernet";
+		enable-active-high;
+		gpio = <&pio 0 20 GPIO_ACTIVE_HIGH>;
+	};
+
+ 	aliases {
+ 		ethernet1 = &rtl8189etv;
+ 	};
+@@ -71,3 +85,7 @@
+ 		reg = <1>;
+ 	};
+ };
+
+&usbphy {
+	usb1_vbus-supply = <&reg_vcc_usb_eth>;
+};
--- a/target/linux/sunxi/patches-4.14/202-ARM-dts-sun8i-activate-SPI-on-Orange-Pi-R1.patch
+++ b/target/linux/sunxi/patches-4.14/202-ARM-dts-sun8i-activate-SPI-on-Orange-Pi-R1.patch
@@ -0,0 +1,29 @@
+From 4a36ec1f82db3fa34d766dec5062b4de06b50f7f Mon Sep 17 00:00:00 2001
+From: Hauke Mehrtens <hauke@hauke-m.de>
+Date: Thu, 28 Dec 2017 14:11:36 +0100
+Subject: [PATCH] ARM: dts: sun8i: activate SPI on Orange Pi R1
+
+This board has a SPI flash, activate it also in device tree by default.
+
+Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
+---
+ arch/arm/boot/dts/sun8i-h2-plus-orangepi-r1.dts | 4 ++++
+ 1 file changed, 4 insertions(+)
+
+--- a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-r1.dts
+++ b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-r1.dts
+@@ -68,6 +68,14 @@
+ 	};
+ };
+ 
+&spi0 {
+	status = "okay";
+
+	flash@0 {
+		compatible = "mxicy,mx25l12805d", "jedec,spi-nor";
+	};
+};
+
+ &ohci1 {
+ 	/*
+ 	 * RTL8152B USB-Ethernet adapter is connected to USB1,
--- a/target/linux/sunxi/patches-4.14/220-ARM-dts-orange-pi-zero-plus.patch
+++ b/target/linux/sunxi/patches-4.14/220-ARM-dts-orange-pi-zero-plus.patch
@@ -0,0 +1,185 @@
+From 0e2da1a792a21e3933e17727920ed3c35a3ba57a Mon Sep 17 00:00:00 2001
+From: Hauke Mehrtens <hauke@hauke-m.de>
+Date: Sun, 11 Mar 2018 15:13:30 +0100
+Subject: [PATCH] arm64: allwinner: H5: Add Xunlong Orange Pi Zero Plus
+
+The Xunlong Orange Pi Zero Plus is single board computer.
+- H5 Quad-core 64-bit Cortex-A53
+- 512MB DDR3
+- microSD slot
+- Debug TTL UART
+- 1000M/100M/10M Ethernet RJ45
+- Realtek RTL8189FTV
+- Spi flash (2MB)
+- One USB 2.0 HOST, One USB 2.0 OTG
+
+This is based on a patch from armbian:
+https://github.com/armbian/build/blob/master/patch/kernel/sunxi-next/sunxi-add-orangepi-zero-plus.patch
+
+Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
+---
+ arch/arm64/boot/dts/allwinner/Makefile             |   1 +
+ .../dts/allwinner/sun50i-h5-orangepi-zero-plus.dts | 147 +++++++++++++++++++++
+ 2 files changed, 148 insertions(+)
+ create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus.dts
+
+--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
+@@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-p
+ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb
+ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb
+ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-prime.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus.dtb
+ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus2.dtb
+ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-nanopi-neo2.dtb
+ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-nanopi-neo-plus2.dtb
+--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus.dts
+@@ -0,0 +1,147 @@
+/*
+ * Copyright (C) 2016 ARM Ltd.
+ * Copyright (C) 2018 Hauke Mehrtens <hauke@hauke-m.de>
+ *
+ * SPDX-License-Identifier: (GPL-2.0+ OR X11)
+ */
+
+/dts-v1/;
+#include "sun50i-h5.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+	model = "Xunlong Orange Pi Zero Plus";
+	compatible = "xunlong,orangepi-zero-plus", "allwinner,sun50i-h5";
+
+	reg_vcc3v3: vcc3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	aliases {
+		ethernet0 = &emac;
+		ethernet1 = &rtl8189ftv;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		pwr {
+			label = "orangepi:green:pwr";
+			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PA10 */
+			default-state = "on";
+		};
+
+		status {
+			label = "orangepi:red:status";
+			gpios = <&pio 0 17 GPIO_ACTIVE_HIGH>; /* PA17 */
+		};
+	};
+
+	reg_gmac_3v3: gmac-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "gmac-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <100000>;
+		enable-active-high;
+		gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */
+	};
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_rgmii_pins>;
+	phy-supply = <&reg_gmac_3v3>;
+	phy-handle = <&ext_rgmii_phy>;
+	phy-mode = "rgmii";
+	status = "okay";
+};
+
+&external_mdio {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins_a>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+	status = "okay";
+};
+
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins_a>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	/*
+	 * Explicitly define the sdio device, so that we can add an ethernet
+	 * alias for it (which e.g. makes u-boot set a mac-address).
+	 */
+	rtl8189ftv: sdio_wifi@1 {
+		reg = <1>;
+	};
+};
+
+&spi0  {
+	status = "okay";
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "mxicy,mx25l1606e", "winbond,w25q128";
+		reg = <0>;
+		spi-max-frequency = <40000000>;
+	};
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbphy {
+	/* USB Type-A ports' VBUS is always on */
+	usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+	status = "okay";
+};
--- a/target/linux/sunxi/patches-4.14/310-Revert-ARM-dts-sun7i-Add-BCM53125-switch-nodes-to-th.patch
+++ b/target/linux/sunxi/patches-4.14/310-Revert-ARM-dts-sun7i-Add-BCM53125-switch-nodes-to-th.patch
@@ -0,0 +1,88 @@
+From 49cd9ea6dc8d68eb519ccd9f31c9730dec8a181a Mon Sep 17 00:00:00 2001
+From: Hauke Mehrtens <hauke@hauke-m.de>
+Date: Thu, 8 Mar 2018 22:14:50 +0100
+Subject: [PATCH] Revert "ARM: dts: sun7i: Add BCM53125 switch nodes to the
+ lamobo-r1 board"
+
+This reverts the changes needed for the upstream b53 DSA switch driver 
+to use the OpenWrt b43 swconfig switch driver.
+
+This reverts commit 0cdefd5b5485ee6eb3512a75739d09a4090176ed.
+This reverts commit d7b9eaff5f0ca00726336b4c0c3c29decf30412a.
+---
+ arch/arm/boot/dts/sun7i-a20-lamobo-r1.dts | 60 ++-----------------------------
+ 1 file changed, 3 insertions(+), 57 deletions(-)
+
+--- a/arch/arm/boot/dts/sun7i-a20-lamobo-r1.dts
+++ b/arch/arm/boot/dts/sun7i-a20-lamobo-r1.dts
+@@ -109,67 +109,13 @@
+ &gmac {
+ 	pinctrl-names = "default";
+ 	pinctrl-0 = <&gmac_pins_rgmii_a>;
+	phy = <&phy1>;
+ 	phy-mode = "rgmii";
+ 	phy-supply = <&reg_gmac_3v3>;
+ 	status = "okay";
+ 
+-	fixed-link {
+-		speed = <1000>;
+-		full-duplex;
+-	};
+-
+-	mdio {
+-		compatible = "snps,dwmac-mdio";
+-		#address-cells = <1>;
+-		#size-cells = <0>;
+-
+-		switch: ethernet-switch@1e {
+-			compatible = "brcm,bcm53125";
+-			reg = <30>;
+-			#address-cells = <1>;
+-			#size-cells = <0>;
+-
+-			ports {
+-				#address-cells = <1>;
+-				#size-cells = <0>;
+-
+-				port0: port@0 {
+-					reg = <0>;
+-					label = "lan2";
+-				};
+-
+-				port1: port@1 {
+-					reg = <1>;
+-					label = "lan3";
+-				};
+-
+-				port2: port@2 {
+-					reg = <2>;
+-					label = "lan4";
+-				};
+-
+-				port3: port@3 {
+-					reg = <3>;
+-					label = "wan";
+-				};
+-
+-				port4: port@4 {
+-					reg = <4>;
+-					label = "lan1";
+-				};
+-
+-				port8: port@8 {
+-					reg = <8>;
+-					label = "cpu";
+-					ethernet = <&gmac>;
+-					phy-mode = "rgmii-txid";
+-					fixed-link {
+-						speed = <1000>;
+-						full-duplex;
+-					};
+-				};
+-			};
+-		};
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+ 	};
+ };
+ 
--- a/target/linux/sunxi/profiles/00-default.mk
+++ b/target/linux/sunxi/profiles/00-default.mk
@@ -0,0 +1,27 @@
+#
+# Copyright (C) 2017 Yousong Zhou
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+define Profile/Default
+  NAME:=Default Profile (all drivers)
+  PACKAGES:= \
+	kmod-ata-core \
+	kmod-ata-sunxi \
+	kmod-brcmfmac \
+	kmod-rtc-sunxi \
+	kmod-rtl8192cu \
+	kmod-rtl8xxxu \
+	kmod-sun4i-emac \
+	rtl8188eu-firmware \
+	swconfig \
+	wpad-mini
+  PRIORITY := 1
+endef
+
+define Profile/Default/Description
+  Default profile with package set compatible with most boards.
+endef
+$(eval $(call Profile,Default))