When a running wake_tx_queue() call is aborted due to a hw queue stop
the corresponding iTXQ is not always correctly marked for resumption:
wake_tx_push_queue() can stops the queue run without setting
@IEEE80211_TXQ_STOP_NETIF_TX.
Without the @IEEE80211_TXQ_STOP_NETIF_TX flag __ieee80211_wake_txqs()
will not schedule a new queue run and remaining frames in the queue get
stuck till another frame is queued to it.
Fix the issue for all drivers - also the ones with custom wake_tx_queue
callbacks - by moving the logic into ieee80211_tx_dequeue() and drop the
redundant @txqs_stopped.
@IEEE80211_TXQ_STOP_NETIF_TX is also renamed to @IEEE80211_TXQ_DIRTY to
better describe the flag.
Fixes: c850e31f79f0 ("wifi: mac80211: add internal handler for
wake_tx_queue")
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
ERROR: Input tree has errors, aborting (use -f to force output)
arch/arm/boot/dts/qcom-ipq8064.dtsi:1686.14-1698.5: ERROR (phandle_references): /soc/amba/nss-common: Reference to non-existent node or label "smb208_s1b"
A commit which made their way into Linux stable down to 5.15 broke the
SATA support on the BPi-R64.
Fix this by importing a (still pending) patch re-adding the 'syscon'
compatible to the pciesys clock-controller which also contains phy-mode
bits referenced by the ahci_mtk driver expecting to access them using
syscon_regmap_lookup_by_phandle().
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 69890e16b3)
Supported devices are listed in the metadata as the first part of the
DTS compatible. This normally follows the format "vendor,device".
When updating the device name of the 180W 1920-8G PoE an underscore was
used, instead of a comma, to join the vendor and device name. This will
lead to warnings for users wanting to sysupgrade a device with an older
compatible, as the device's info does not match the one the metadata.
Fixes: 987c96e889 ("realtek: rename hpe,1920-8g-poe to match hardware")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 6a7fa68569)
This patch has been accepted for linux v6.14 so we can move it from pending
to backport.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 2f2e21a52b)
This patch is needed on bmips since it fixes issues with GPIOs not being
properly configured due to gpio_request_enable not being called on bcm63xx
devices. Therefore we can now drop the bcm63268 gpio function patch.
Backported from f5b1d340be with the exception of
the realtek and bmips patches removal.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit f5b1d340be)
The Sophos AP15C uses the same hardware as the AP15, but has a reset button.
Based on:
commit 6f1efb2898 ("ath79: add support for Sophos AP100/AP55 family")
author Andrew Powers-Holmes <andrew@omnom.net>
Fri, 3 Sep 2021 15:53:57 +0200 (23:53 +1000)
committer Hauke Mehrtens <hauke@hauke-m.de>
Sat, 16 Apr 2022 16:59:29 +0200 (16:59 +0200)
Unique to AP15C:
- Reset button
- External RJ45 serial console port
Flashing instructions:
This firmware can be flashed either via a compatible Sophos SG or XG
firewall appliance, which does not require disassembling the device, or via
the U-Boot console available on the internal UART header.
To flash via XG appliance:
- Register on Sophos' website for a no-cost Home Use XG firewall license
- Download and install the XG software on a compatible PC or virtual
machine, complete initial appliance setup, and enable SSH console access
- Connect the target AP device to the XG appliance's LAN interface
- Approve the AP from the XG Web UI and wait until it shows as Active
(this can take 3-5 minutes)
- Connect to the XG appliance over SSH and access the Advanced Console
(Menu option 5, then menu option 3)
- Run `sudo awetool` and select the menu option to connect to an AP via
SSH. When prompted to enable SSH on the target AP, select Yes.
- Wait 2-3 minutes, then select the AP from the awetool menu again. This
will connect you to a root shell on the target AP.
- Copy the firmware to /tmp/openwrt.bin on the target AP via SCP/TFTP/etc
- Run `mtd -r write /tmp/openwrt.bin astaro_image`
- When complete, the access point will reboot to OpenWRT.
To flash via U-Boot serial console:
- Configure a TFTP server on your PC, and set IP address 192.168.99.8 with
netmask 255.255.255.0
- Copy the firmware .bin to the TFTP server and rename to 'uImage_AP15C'
- Open the target AP's enclosure and locate the 4-pin 3.3V UART header [4]
- Connect the AP ethernet to your PC's ethernet port
- Connect a terminal to the UART at 115200 8/N/1 as usual
- Power on the AP and press a key to cancel autoboot when prompted
- Run the following commands at the U-Boot console:
- `tftpboot`
- `cp.b $fileaddr 0x9f070000 $filesize`
- `boot`
- The access point will boot to OpenWRT.
Signed-off-by: David Lutz <kpanic@hirnduenger.de>
The kernel logs the error "bcm6368_nand 10000200.nand: there is not valid
maps for state default" on boot and all nand pins show as UNCLAIMED in
sysfs pinmux-pins.
bcm6362.dtsi, bcm6368.dtsi and bcm63268.dtsi use the undocumented property
group which the driver doesn't understand. This has been documented upstream
in commit caf963efd4b0b9ff42ca12e52b8efe277264d35b.
Replacing group with pins allows the nand pins to be properly configured.
Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com>
[add bcm636/bcm6368 and fix commit title]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit d1e9c50d06)
Recent changes to BuildBot config moved the kmods to a dedicated
directory and dropped them from the packages dir. This was needed as
both OPKG and APK gets confused if both entry are present.
To fix this, unconditionally append the kmod feed line if
CONFIG_BUILDBOT is enabled.
Fixes: #17146
Link: https://github.com/openwrt/openwrt/pull/17151
(cherry picked from commit 53ee2e8c03)
[ fix conflict error for missing APK support ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
