6.12 PWM core introduced a bunch of incompatible changes, namely removal
of manual module owner assignment, complete PWM struct allocation and usage
refactor, etc.
So, update the driver to follow other drivers in 6.12 so it compiles.
Link: https://github.com/openwrt/openwrt/pull/18795
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refresh kernel config by running kernel_menuconfig.
Manually enable CONFIG_HW_RANDOM and CONFIG_CRYPTO_DEV_QCOM_RNG as these
got somehow disabled by the refresh.
Link: https://github.com/openwrt/openwrt/pull/18795
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refresh 6.12 patches, those that failed automatic refresh were refreshed
manually.
DT bindings patches that failed were dropped as we dont use them in practice.
Link: https://github.com/openwrt/openwrt/pull/18795
Signed-off-by: Robert Marko <robimarko@gmail.com>
CONFIG_IDPF is Intel(R) Infrastructure Data Path Function Support and it
should be disabled by default, if needed it can be packaged as a kmod.
Disable to prevent spreading out through target configs.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Noticed that CONFIG_HISILICON_ERRATUM_162100801 was being added to
qualcommax 6.12 config.
Since we dont support any Hisilicon chips, disable it in generic config
before it starts spreading in target configs.
Signed-off-by: Robert Marko <robimarko@gmail.com>
DRM_ACCEL symbols were not added to geode and legacy thus making the kernel
prompt for them on compilation.
Fixes: 51b78aaaae ("kernel: package intel_vpu driver")
Signed-off-by: Robert Marko <robimarko@gmail.com>
RFC4541, section 2.1.2 says:
Packets with a destination IP (DIP) address in the 224.0.0.X range
which are not IGMP must be forwarded on all ports.
And section 3 says:
In IPv6, the data forwarding rules are more straight forward because
MLD is mandated for addresses with scope 2 (link-scope) or greater.
The only exception is the address FF02::1 which is the all hosts
link-scope address for which MLD messages are never sent. Packets
with the all hosts link-scope address should be forwarded on all
ports.
However, currently when a listener on FF12::1 or FF12:🔢0:1 for
example joins then not only packets to these addresses but also for
FF02::1 won't be flooded to all ports anymore, too. Which violates
RFC4541.
This happens because A): They all map to the same ethernet multicast
address, that is 33:33:00:00:00:01. And B) the VLAN profile L2
unknown MC flood setting will only apply flooding of 33:33:00:00:00:01
if there is no specific listener registered for it.
So to fix this, avoid registering an MDB entry in the switch for
33:33:00:00:00:01 at all.
The downside of this is that FF12::1, FF12:🔢0:1 etc.
will always be flooded, too. However fixing the handling of 224.0.0.X
and FF02::1 and adhering to RFC4541 must have priority to avoid
undesired packetloss, to avoid breaking IPv4/IPv6.
Tested-on: ZyXEL GS1900-24HP v1
Fixes: cde31976e3 ("realtek: Add support for Layer 2 Multicast")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Link: https://github.com/openwrt/openwrt/pull/18769
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fixes the following warning:
[ 180.314652] NOHZ tick-stop error: local softirq work is pending, handler #08!!!
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Currently, non existing ipq-wifi package name is selected for
EAP625-Outdoor HD, so correct the name.
Fixes: 51c1ea08d0 ("qualcommax: ipq60xx: add TP-Link EAP625-Outdoor HD v1 support")
Signed-off-by: Robert Marko <robimarko@gmail.com>
TP-Link EAP625-Outdoor HD is a 802.11ax AP claiming AX1800 support.
It is wall or pole mountable, and rated for outdoor use. It can only
be powered via PoE.
Hardware-wise, it is very similar to the older EAP610-Outdoor model.
Software-wise, I couldn't find a difference other than the board
data files, and device name. For this reason, the majority of the
devicetree from the EAP610-Outdoor is reused.
This device currently comes in a "v1", and "v1.6" version. The
"support-list" of the vendor firmware does not have a distinction
between these versions. This commit was tested on a 'V1.6" device.
Specifications:
---------------
* CPU: Qualcomm IPQ6018 Quad core Cortex-A53
* RAM: 512 MB
* Storage: 128MB NAND
* Ethernet:
* Gigabit RJ45 port with PoE input
* WLAN:
* 2.4GHz/5GHz
* LEDs:
* Multi-color System LED (Green/Amber)
* Buttons:
* 1x Reset
* UART: 4-pin unpopulated header
* 1.8 V level, Pinout 1 - TX, 2 - RX, 3 - GND, 4 - 1.8V
Installation:
=============
Web UI method
-------------
Set up the device using the vendor's web UI. After that go to
Management->SSH and enable the "SSH Login" checkbox. Select "Save".
The connect to the machine via SSH:
ssh -o hostkeyalgorithms=ssh-rsa <ip_of_device>
Disable signature verification:
cliclientd stopcs
Rename the "-web-ui-factory" image to something less than 63
characters, maintaining the ".bin" suffix.
* Go to System -> Firmware Update.
* Under "New Firmware File", click "Browse" and select the image
* Select "Update" and confirm by clicking "OK".
If the update fails, the web UI should show an error message.
Otherwise, the device should reboot into OpenWRT.
NOTE: If ssh continues to complain that "no matching host key type
found. Their offer: ssh-rsa,ssh-dss" it likely means that yor distro
has completely disabled deprecated siphers in ssh. In that case, run
the ssh command from a docker container of an older distro.
TFTP method
-----------
To flash via tftp, first place the initramfs image on the TFTP server.
setenv serverip <ip of tftp server>
setenv ipaddr <ip in same subnet as tftp server>
tftpboot tplink_eap625-outdoor-hd-v1-initramfs-uImage.itb
bootm
This should boot OpenWRT. Once booted, flash the sysupgrade.bin image
using either luci or the commandline.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18584
Signed-off-by: Robert Marko <robimarko@gmail.com>
I have an EAP625-Outdoor HD v1 that is very similar with the EAP610
Outdoor. It works with the EAP610 initramfs, without any obvious loss
of functionality. In order to prepare for supporting the EAP625, move
the common parts into a shared .dtsi.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18584
Signed-off-by: Robert Marko <robimarko@gmail.com>
The web-recovery of the Genexis EX400 validates uploaded images to fit
in the rootf_0 partition.
With OpenWrt, only the kernel is stored in this partition, leaving the
partition very small. Currently, the first factory release image won't
be accepted by the recovery interface after the OpenWrt installation.
Pad the image of the ubifs to 10MB. This allows the 24.10 release image
to be uploaded, enabling device recovery.
Signed-off-by: David Bauer <mail@david-bauer.net>
Clean the temporary directory the UBI image is generated from before
generation.
Currently it is removed after the image generation, which leads to files
possibly not being cleared after a build failure in this step.
Signed-off-by: David Bauer <mail@david-bauer.net>
bcm6328, bcm6362 and bcm6368 targets are missing a key config symbol which
prevents the NAND from working.
Fixes: f6c02b014d ("bmips: 6.1: refresh config and add missing symbols")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
CONFIG_PAHOLE_HAS_LANG_EXCLUDE is set depending on the pahole version
present, so it must be filtered out.
Signed-off-by: Robert Marko <robimarko@gmail.com>
For kernel 6.12 there is a warning causing an error:
drivers/mtd/nand/mtk_bmt_v2.c: In function 'mtk_bmt_get_mapping_mask':
drivers/mtd/nand/mtk_bmt_v2.c:307:31: error: 'kmalloc_array_noprof' sizes specified with 'sizeof' in the earlier argument and not in the later argument [-Werror=calloc-transposed-args]
307 | used = kcalloc(sizeof(unsigned long), BIT_WORD(bmtd.bmt_blk_idx) + 1, GFP_KERNEL);
| ^~~~~~~~
Swapping the arguments solves the problem.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18701
Signed-off-by: Robert Marko <robimarko@gmail.com>
Kernel does
if (phydev->drv->set_loopback)
ret = phydev->drv->set_loopback(phydev, enable, speed);
else
ret = genphy_loopback(phydev, enable, speed);
So no need to explicitly set genphy_loopback() in phy_driver. Drop
references to let kernel do its work.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18782
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that IPQ50xx PCIe nodes have linux,pci-domain property defined
it changed the PCI path, but its now predictable and fixed.
So, update the caldata script accordingly.
Link: https://github.com/openwrt/openwrt/pull/18789
Signed-off-by: Robert Marko <robimarko@gmail.com>
It seems that bus-range property was missed for the PCIe bridges on
IPQ50xx, thus causing DTC to warn on any bus adress used on nodes
under the PCIe bridges.
Link: https://github.com/openwrt/openwrt/pull/18789
Signed-off-by: Robert Marko <robimarko@gmail.com>
We are lucky to have a working realtek environment. But some things where mixed
heavily. To say it clear a bus is a bus and an ethernet is an ethernet. With
the new naming conventions and defines this becomes even more obvious.
Decouple it by moving the bus specific parts out of the ethernet device. To
make the code more readable rename bus_priv variables to priv and sort variable
definitions in inverse tree order (length descending) where it makes sense.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18402
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
At least since 2022 there is a major bug in the MDIO driver that
produces out-of-bound reads and erratic behaviour during initialization.
- mdiobus_scan_bus_c22() scans the bus for 64 devices (PHY_MAX_ADDR)
- private bus structure only supports 57 entry arrays (MAX_PORTS)
All the bus/reader writer functions accept calls with addr>=57 and will
silently read beyond their limits. This can lead to ghost SERDES like
https://github.com/openwrt/openwrt/issues/18665#issuecomment-2846053813
Add proper boundary checks and end the functions with -ENODEV that is
the only accepted error code from the bus scan function.
Fixes: 0536c582e6 ("realtek: Fix RTL931X Ethernet driver") etc ...
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18402
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Relocate the bus structure definition into the MDIO source code area
of the ethernet driver. So if the real bus driver is forked from the
rest of the code only one area needs to be removed. Rename it to make
clear it belongs to the bus.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18402
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Inside the ethernet driver lives the mdio bus. It is not always clear
what belongs where. Prefix some leftovers from the kernel 6.6 refactor
to clearly state what belongs to the bus. Group all defines together
in one place. This commit has no functional changes.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18402
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
