This change hides an unnecessary error that appears when qca-nss
acceleration is enabled.
```
[41893.868166] phy1-ap0: NSS TX failed with error:
NSS_TX_FAILURE_TOO_SHORT
[42192.779516] phy1-ap0: NSS TX failed with error:
NSS_TX_FAILURE_TOO_SHORT
```
This change fixes the following issue...
```
<0>[ 3372.560724] fortify_panic from ecm_db_exit+0x384/0x388 [ecm]
<0>[ 3372.568927] ecm_db_exit [ecm] from
ecm_db_ipv6_route_table_update_event+0x3c/0x5c [ecm]
<0>[ 3372.574608] ecm_db_ipv6_route_table_update_event [ecm] from
atomic_notifier_call_chain+0x58/0x6c
<0>[ 3372.582769] atomic_notifier_call_chain from
ip6_route_add+0xac/0xdc
<0>[ 3372.591533] ip6_route_add from inet6_rtm_newroute+0xb0/0xc0
```
An additional bit is needed to enable 256-QAM support. Feature that is
already supported in ath10k-ct driver.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Permit to configure vht_capab also for 2.4GHz 802.11n mode to support
non-standard QAM-256 on 802.11n.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add support for QAM-256 in 2.4GHz 802.11n. This is non-standard and
comunicate vht capabilities in 2.4GHz 802.11n permittin, for supported
clients, to benefits for additional data rate.
Many driver supports this, for a start enable this for ath10k and
ath11k.
Before I can get to work a feed repository that work i have included
qca-nss source needed on this commit
Source author: SqTER-PL <r.napierala@asta-net.pl>
This commit changes LAN1 to be WAN and LAN2 to be LAN, like all other
dual port Extreme Networks devices.
This partially reverts commit 84a489b7cf
Signed-off-by: Christian Schmidbauer <github@grische.xyz>
(cherry picked from commit 710ec82367)
Fixes LAN LED "1" to show activity of LAN1 and LAN LED "2" to show
activity of LAN2, not vice versa.
Signed-off-by: Christian Schmidbauer <github@grische.xyz>
(cherry picked from commit f02e614f50)
hostapd_neighbor_set_own_report is normally called from interface setup only.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 9850052190)
Ensure that hapd->own_addr is set properly, since hostapd_setup_bss
only handles it for secondary BSS interfaces
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 3ebf110711)
The WR3000E has the same board layout as the WR3000S. Differences:
- Different flash chip
- LEDs with red/blue colour intead of white
Hardware:
- MediaTek MT7981 WiSoC
- 256MB DDR3 RAM
- 128MB SPI-NAND (F50L1G41LB)
- MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
MAC Addresses in OEM firmware:
- There is one on the label, e.g. AA:BB:CC:DD:EE:FF
- WLAN (2.4G) uses the same as on the label
- WLAN (5G) is the one on the label but
- first byte (e.g. AA) + 2
- fourth byte (e.g. DD) - 0x40
- WAN is the one on the label + 1
- LAN is the one on the label
MAC Addresses in OpenWrt:
- Same handling as in WR3000s is used
GPIO:
- 2 Buttons (all low active):
- WPS on GPIO 0
- Reset on GPIO 1
- 6 LEDs (all low active):
- Power: Blue on GPIO 8, no red LED
- WPS: Blue on GPIO 10, Red on GPIO 4
- Internet: Blue on GPIO 11, no red LED
- LAN: Blue on GPIO 9, Red on GPIO 5
- WiFi 2.4G: Blue on GPIO 6, no red LED
- WiFi 5G: Blue on GPIO 7, no red LED
Disassembly:
- Remove the 4 screws at the bottom of the case
- Cover is clipped to the bottom part of the case with clips in the front and the back
UART:
- UART pins are accessible on the bottom of the board
- The connector with the square shape is TX
- Pins: [ ] TX, ( ) RX, ( ) GND, ( ) VCC
- Settings: 115200 8N1 3.3V
Migration to OpenWrt via OEM firmware:
- There should be a migration image available from Cudy as soon as there is official OpenWrt support
- Download the migration image via OEM web interface
- After flashing, OpenWrt is accessible via 192.168.1.1
- Flash the official OpenWrt image
Migration to OpenWrt using TFTP:
- Connect UART as described above
- Press the reset button while powering on the device
- U-Boot will now try to load a recovery.bin via TFTP, this must be ignored
- After detecting a timeout, the U-Boot console is available via UART
- Set up a TFTP server on IP 192.168.1.88 and connect it to one of the LAN ports
- Provide the initramfs image via TFTP as cudy3000e.bin
- Run the following command in U-Boot: tftpboot 0x46000000 cudy3000e.bin; bootm 0x46000000
- OpenWrt initramfs image is now booting and accessible via 192.168.1.1
- Flash the sysupgrade image
Revert back to OEM:
- Set up a TFTP server on IP 192.168.1.88 and connect it to one of the LAN ports
- Provide the Cudy firmware via TFTP as recovery.bin
- Press the reset button while powering on the device
- Recovery process will start now
- After recovery is done, the OEM firmware is available at 192.168.10.1 again
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18609
(cherry picked from commit 300335f1ff)
Link: https://github.com/openwrt/openwrt/pull/19063
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Following the initial support of the Cudy WR3000H with PHY C22 for the 2.5G WAN
interface, several improvements fixing issues with RealTek RTL8221B PHYs have
been merged.
Therefore we can now bring the DT in line with other equipment and declare the
2.5G WAN PHY as C45.
Fixes: 9d66b8b ("mediatek: filogic: Add support for cudy wr3000h")
Signed-off-by: Juan Pedro Paredes Caballero <juanpedro.paredes@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17739
[reword commit description]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit dcc5587374)
Link: https://github.com/openwrt/openwrt/pull/19124
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The manufacturer Cudy usually releases signed openwrt firmware, to
facilitate the migration from the proprietary version to the official
versions of openwrt. In contact with the manufacturer tells me that only
releases the firmware of the WR3000H if and only if
there is an official version. With this proposal I pretend to have an
initial operative version so that they do their part, and facilitate to
the users the possibility of using openwrt. In the present state, it is
only possible to use this firmware by uploading and installing it with
UART connection.
AX3000 2.5G Dual Band Wi-Fi 6 Mesh Router (WR3000H)
Hardware
--------
MediaTek MT7981 WiSoC
256MB DDR3 RAM
128MB SPI-NAND (XMC XM25QH128C)
MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
4 LAN MediaTek MT7531 PHY
1 WAN RTL8221B-VB-CG 2.5Gbps PHY (C22)
2 Radios MT7976CN
UART: 115200 8N1 3.3V
MAC:
LAN MAC: label mac
WAN MAC: label mac + 1
2.4G MAC: label mac
5G MAC: label mac + 1 with LA bit set
Installation
------------
1. Connect to the serial port as described in the "Hardware" section.
2. Power on the device + press reset pin. Keep pressing reset pin to
enter the U-Boot shell (The recovery.bin image load process must fail).
3. Download the OpenWrt initramfs image. Place it on an TFTP server
connected to the Cudy LAN ports. Make sure the server is reachable at
192.168.1.88. Rename the image to "cudy3000h.bin"
4. Download and boot the OpenWrt initramfs image.
$ tftpboot 0x46000000 cudy3000h.bin; bootm 0x46000000
5. IMPORTANT: Make backup from original firmware. System -> Backup
/Flash Firmware -> Save mtdblock contents. All mtdblock one by one,
keep unaltered (BL2, u-boot-env, Factory, bdinfo, FIP, and ubi).
6. Transfer the OpenWrt sysupgrade image to the device using scp.
Install with sysupgrade.
Warning for BL2 and U-BOOT developers
-------------------------------------
The nand partition layout from vendor is slightly diferent from "standard".
The FIP partition starts at 0x3c0000 be carefull with BL2 to BL31.
The UBI partition start at 0x5c0000 be carefull.
DO NOT OVERWRITE bdinfo partition it contains hardware MAC definition
Layout is start-end (not start size)
- 0x000000000000-0x000007800000 : "nmbm0"
- 0x000000000000-0x000000100000 : "bl2"
- 0x000000100000-0x000000180000 : "u-boot-env"
- 0x000000180000-0x000000380000 : "factory"
- 0x000000380000-0x0000003c0000 : "bdinfo"
- 0x0000003c0000-0x0000005c0000 : "fip"
- 0x0000005c0000-0x0000045c0000 : "ubi"
ALLWAYS for U-BOOT operations check this
setenv mtdids nmbm0=nmbm0
setenv mtdparts nmbm0:1024k(bl2),512k(u-boot-env),2048k(factory),256k(bdinfo),2048k(fip),65536k(ubi)
Signed-off-by: Juan Pedro Paredes Caballero <juanpedro.paredes@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17458
(cherry picked from commit 9d66b8b312)
Link: https://github.com/openwrt/openwrt/pull/19124
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
drop upstream patches
$ git log --no-merges --oneline v2.7.6..v2.8
48ceda8 Version 2.8
b3d0c93 Regression in commit abe92e8010ab affecting MariaDB tests
29fced6 Count traditional diff pattern lines correctly
b5d2124 patch: fix --no-backup-if-mismatch regression
86ac7e2 Fix dodgy assert with side-effects in insert_cached_dirfd
7d87652 Declare an expected test failure on Haiku.
86baf97 build: update gnulib submodule to latest
1ba2c1b Fix two test failures on Haiku.
1da6bf8 Check for newlines only when creating a file name
30ee610 Gnulib renamed some modules
6dbc381 maint: update bootstrap from gnulib
05ac924 build: update gnulib submodule to latest
95e0092 maint: make update-copyright
5bac274 Set --no-backup-if-mismatch when in --posix mode
910fecf Add missing feature tests to the test suite
be8b3c6 Disable release-prep
c61485b Fix "make release" to handle alpha releases
499916f Add announce-gen module for "make release"
adb1ebc Pacify gcc -fsanitize=address
6bdae94 Fix memory leak when malformed unidiff patch
72a146c Port to clang address sanitizer
e2e6820 Refactor argc+argv processing
606c091 Omit needless get_some_switches code
ee3cc40 Revert "Remove obsolete require_gnu_diff function"
8cae4fc Remove obsolete require_gnu_diff function
164b529 savebuf can return a null pointer
91c1e4f Spelling fixes
a03e1ba Port other reject-format test to non-GNU diff
9ba5eb0 Don’t be fooled by NUL bytes in diff directives
79dd5e7 Don’t be fooled by "\000" in file name
8492a6a Port to quasi-GNU diff
f6f2c6f In previous patch, make w_q static
0525681 Pacify -Wunterminated-string-initialization
301411d Spelling fixes
4615206 Remove double semicolon
923e0ef Prefer angle bracket headers
5d17ca0 Update more old copyright notices
5f4edd3 Simplify memory allocation of files to delete
802511c Report patch read errors more immediately
a93b50d Port fflush usage to OpenBSD 7.5
55e224b Update old copyright notices
33a7fd8 Fix gl_gcc_warnings typo in ‘configure’
2313b37 build: update gnulib submodule to latest
37fec39 Remove some dependencies no longer needed
cc87173 Update NEWS as per recent changes
7887622 Update POSIX citations
18f4dd6 Use “Gruenbacher” in international contexts
638675c Adjust libs to match recent Gnulib
53400a1 Pacify clang -Wbitwise-conditional-parentheses
e8e1bcb Remove “support” for nested critical sections
b963510 Simplify critical section code in util fns
85949fb Shrink critical sections
448ff9b Defer signals by hand with sigatomic_t
b95a603 output_file_later avoid a malloc+free pair
2663228 Defend against closed stdin/stdout/stderr
fc77964 Stop using Gnulib ‘execute’ module
470699c Move defer_signals up
f696e4e Make sigs, NUM_SIGS local
4d3a4ab Rename block_signals
b3bb925 Trade a bit of space for time in parse_c_string
070d859 Allocate first patchbuf statically
f46a90f Use bigger buffer size by default
2e64cfd Preinitialize fatal_act.sa_hander
45de0d9 Prefer EXIT_SUCCESS etc. to literal integers
82c4940 Fix some signal handling races
eceea61 Fix --set-utc TZ setting
9c55d3f Improve logic for when rename removes source
61c72f0 Fix signal race when renaming file
705c9bc Simplify traverse_another_path via last_component
77f21a6 Stop using Gnulib dirname module
fe8ffd9 Fix implausible overflow when reading symlinks
5e84bda Access checks should use effective, not real
8d4ca49 Don’t assume AT_FDCWD != -1
fe5d4a0 Copy input to output attributes via fd if possible
ca4c431 Simplify timestamp epoch checking
0ad4347 Check for ftello failures
c49a16d Remove format_linenum
22efdee Fix "with multiple words" line number
5a70a1b Drop Plan B
c0d465f Prefer ximemdup0 to xmemdup0
b91aab2 Refactor ifetch API
55c8a5c Do not attempt huge I/Os
e0e121e Use outfd when setting file attributes
241e57e Don’t assume Linux-like S_IFREG
0f8c628 Use STDOUT_FILENO etc
f2c3676 Fix unlikely glitch with ed diffs
cec6407 Use fds to copy attrs in create_backup_copy
6b7b01b Be more careful about (time_t) -1
0433553 X == -1 → X < 0
0a66dee Let set_file_attributes use fds not names
36ff2c9 Port to narrow unsigned uid_t
3951496 Check for output errors more systematically
6429630 Report input error right away
03cb187 Simplify EOF testing
cc7cde7 Prefer other types to ‘int’
4c6650b Detect unlikely integer overflow in size calcs
abe92e8 Prefer idx_t, ptrdiff_t to lin
30449e2 Fix compatibility issue with blanks in patches
9228a8c pch_swap return type cleanup
c1c438d Fix unlikely int overflow in hunk counts
5d3f41f Use char for char in plan_a
fb056f2 Cache cwd_is_root dev, ino
84b5f34 Avoid ‘unsigned’ in safe.c
d2e113e Simplify get_sha1
f73718b Avoid casts in patch.c
79eef3e Prefer idx_t in util.c
11588d0 Prefer idx_t in pch.c
e16037d Prefer idx_t in patch.c
388926f Prefer idx_t in list.h
3582fdb Prefer idx_t in inp.c
4a47c00 build: update gnulib submodule to latest
4f8c4b8 Don’t limit strip counts etc. to INT_MAX
0a810b6 Fix unlikely integer overflows in patch.c
bac3b6d Fix unlikely integer overflows in pch.c
8fb784b Fix unlikely integer overflows in inp.c
e10f3ca Promote minmax.h to common.h
57e2165 Avoid some memory allocation by not using ‘const’
eb18b39 Remove unnecessary char * casts in inp.c
d60cb72 Pacify gcc -Wunused-parameter when !USE_XATTR
05ef886 Pacify gcc -Wunused-parameter when !USE_XATTR
1f8d192 maint: stop using alloca
ba92722 Don’t assume O_RDONLY == 0
0f98e03 Avoid syscall when nested signal block
1235ccc Add signal comment
43ee674 build: update gnulib submodule to latest
e381947 Update NEWS, README-prereq
2c2a83b Omit _Noreturn when easy
a13c2ea Replace __attribute__ with attribute.h
6eb2d13 Switch from ctype.h to c-ctype.h
d1a6847 Simplify warning configuration
d6631b3 Prefer ATTRIBUTE_* to _GL_ATTRIBUTE_*
bc6899d Pacify gcc -Wno-unused-parameter
da25985 Improve ‘git diff’ output if desired
248ef13 Prefer strerror to perror
6cb321a A bit more long-string fixing
47bc09d Prefer nullptr to NULL
7608746 More fixing of printing of very long strings
323da0d Don’t assume string sizes fit in int when printing
53d1014 Avoid fprintf INT_MAX overflow when merging
59681c8 Avoid sprintf INT_MAX overflow
4278b91 Reject output file names containing '\n'
34b45bc Update man page a bit.
d18c05d Update copyright notices
af828e5 Fix some races involving signals
b3a6c95 Don’t attempt to remove files we didn’t create
9abc949 Omit goto in try_safe_open
90e62d5 Pacify clang re obsolete O_CREAT test
2b87c1e Allow nested block/unblock of signals
7aa1c3b Adjust to new Gnulib bootstrap post imports
99c0c0b maint: remove generated file lib/Makefile.am
1c087d6 Rely on Gnulib inttypes module
7214f8d Update main locals more consistently
6785b2c Use struct outfile * in function args
72d7ed0 Refactor temp names into struct
abf6fb1 Simplify by using Gnulib sigaction
d3816ac Avoid unnecessary freeing in output_files
346d3ac Clean up cleanup
ff2317b Port better to GNU/Hurd
c2d9792 Don’t say empty backups are unreadable
8c27a03 Spelling fixes
d46d729 Change manywarnings usage to be more like coreutils
924698b Pacify clang, which dislikes n + "y"
8939519 Pacify -Wstrict-overflow in pch.c
531cc2b Pacify -Wsuggest-attribute=format in util.c
ff13fea Port to non-VLA C compilers
3d5c0d1 Rename vars to pacify gcc -Wshadow
56788ce Stop including stdbool.h
c10da77 Recommend 64-bit time_t on 32-bit platforms
1e21767 Remove pch_sha1
39005cf Move skip_spaces
755712d Remove pch_timestamp function
04f0eeb Prefer extern inline to static inline for list.h
f06c123 maint: pacify gcc 14 -Wcast-align
aab6e7b maint: pacify -Wanalyzer-null-argument
d1d32c9 maint: work around GCC bug 109839
7575694 maint: pacify gcc -Wmissing-variable-declarations
8f78b09 maint: pacify gcc -Winline
bb841fd maint: port _FORTIFY_SOURCE to Ubuntu
4887683 maint: assume STDC_HEADERS
5b8ecde maint: spruce up our .m4 files a bit
009a424 maint: omit obsolete macro calls
299167f maint: simplify .gitignore
3ec44a4 build: update gnulib submodule to latest
68cb529 build: update gnulib submodule to latest
f144b35 build: Enable the 'subdir-objects' Automake option.
faafc79 build: update gnulib submodule to latest
c835ecc Pass the correct stat to backup files
24f81be maint: modernize README-{hacking,prereq}
7623b2d Fix test for presence of BASH_LINENO[0]
0993940 gnulib: update to latest
78ed9de Add missing-section tests to context-format test case
76e7758 Fix failed assertion 'outstate->after_newline'
15b158d Avoid invalid memory access in context format diffs
dce4683 Don't follow symlinks unless --follow-symlinks is given
61d7788 Don't crash when RLIMIT_NOFILE is set to RLIM_INFINITY
b7b028a Abort when cleaning up fails
a5b442c Skip "ed" test when the ed utility is not installed
2b584ae Improve support for memory leak detection
9c98635 Fix swapping fake lines in pch_swap
ff81775 Make the (debug & 2) output more useful
369dccc Don't leak temporary file on failed multi-file ed-style patch
1959988 Don't leak temporary file on failed ed-style patch
f322a7e Request 'alloca' module from gnulib.
458ac51 Fix 'ed-style' test failure.
1e9104c Fix check of return value of fwrite().
ae81be0 maint: avoid warnings from GCC8
2a32bf0 Minor cleanups in do_ed_script
ff1d3a6 Use gnulib execute module
3fcd042 Invoke ed directly instead of using the shell
123eaff Fix arbitrary command execution in ed-style patches (CVE-2018-1000156)
b5a91a0 Allow input files to be missing for ed-style patches
f290f48 Fix segfault with mangled rename patch
074e239 Test suite: fix Korn shell incompatibility
f6bc5b1 Test suite compatibility fixes
3bbebbb Avoid set_file_attributes sign conversion warnings
Signed-off-by: Russell Senior <russell@personaltelco.net>
Link: https://github.com/openwrt/openwrt/pull/18479
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit f45df2167b)
TF-A LTS releases have an lts- prefix in their version tag. Introduce a
PKG_LTS variable to support these.
As the non-LTS tarbals do not contain the version prefix in the
directory, we need different PKG_BUILD_DIR for each variant:
➜ tar --list --file dl/trusted-firmware-a-v2.12.tar.gz | head -n1
trusted-firmware-a-2.12/
➜ tar --list --file dl/trusted-firmware-a-lts-v2.12.1.tar.gz | head -n1
trusted-firmware-a-lts-v2.12.1/
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
cherry picked from commit 06c4e8a262
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/19076
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Multiple users have reported a regression [1] in OpenWRT 24.10 with the
ramips/mt7621 target, which has the MT7530 PHYs: the Ethernet link is
periodically going down for a brief period of time:
mt7530-mdio mdio-bus:1f lan1: Link is Down
br-lan: port 1(lan1) entered disabled state
mt7530-mdio mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
The symptoms stop after disabling EEE and it was reported by Mediatek in
2021 that EEE is unstable for the MT7530 PHYs [2]:
> EEE of the 10-year-old MT7530 internal gephy has many IOT problems, so
> it is recommended to disable its EEE.
EEE is enabled by default for these devices in OpenWRT 24.10 whereas in the
previous version (OpenWRT 23.05, Linux 5.15) it was not. It was determined
that in Linux 6.6, the PHY driver tries to disable EEE in
mtk_gephy_config_init() in drivers/net/phy/mediatek-ge.c, but this is later
overridden by a subsequent execution of the genphy_c45_write_eee_adv()
function, which enables every EEE mode supported.
The best way forward for now seems to be to mark EEE as broken directly in
the devicetree, which affects the genphy_c45_write_eee_adv() function.
There are some devices, like GnuBee GB-PC2, that define additional PHYs,
for example ethernet-phy@5 or ethernet-phy@7. As reported by Chester A.
Unal, these are not MT7530 PHYs and they are not affected.
This would need to be cherrypicked for the OpenWRT 24.10 branch.
[1] https://github.com/openwrt/openwrt/issues/17351
[2] https://lore.kernel.org/all/0adde34f936a2dafca40b06b408d82afe0852327.camel@mediatek.com/
Tested-by: Darren Tucker
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Closes: https://github.com/openwrt/openwrt/issues/17351
Link: https://github.com/openwrt/openwrt/pull/18585
(cherry picked from commit b7fa9d92ae)
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Tested-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Link: https://github.com/openwrt/openwrt/pull/19150
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
