This change hides an unnecessary error that appears when qca-nss
acceleration is enabled.
```
[41893.868166] phy1-ap0: NSS TX failed with error:
NSS_TX_FAILURE_TOO_SHORT
[42192.779516] phy1-ap0: NSS TX failed with error:
NSS_TX_FAILURE_TOO_SHORT
```
This change fixes the following issue...
```
<0>[ 3372.560724] fortify_panic from ecm_db_exit+0x384/0x388 [ecm]
<0>[ 3372.568927] ecm_db_exit [ecm] from
ecm_db_ipv6_route_table_update_event+0x3c/0x5c [ecm]
<0>[ 3372.574608] ecm_db_ipv6_route_table_update_event [ecm] from
atomic_notifier_call_chain+0x58/0x6c
<0>[ 3372.582769] atomic_notifier_call_chain from
ip6_route_add+0xac/0xdc
<0>[ 3372.591533] ip6_route_add from inet6_rtm_newroute+0xb0/0xc0
```
An additional bit is needed to enable 256-QAM support. Feature that is
already supported in ath10k-ct driver.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Permit to configure vht_capab also for 2.4GHz 802.11n mode to support
non-standard QAM-256 on 802.11n.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add support for QAM-256 in 2.4GHz 802.11n. This is non-standard and
comunicate vht capabilities in 2.4GHz 802.11n permittin, for supported
clients, to benefits for additional data rate.
Many driver supports this, for a start enable this for ath10k and
ath11k.
Before I can get to work a feed repository that work i have included
qca-nss source needed on this commit
Source author: SqTER-PL <r.napierala@asta-net.pl>
hostapd_neighbor_set_own_report is normally called from interface setup only.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 9850052190)
Ensure that hapd->own_addr is set properly, since hostapd_setup_bss
only handles it for secondary BSS interfaces
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 3ebf110711)
61ae5732adea iprule: amend ipproto netlink nla_put_u32 to nla_put_u8
d610d68c71b8 device: add support for configuring vrf
a1b6386a20a6 device: fix bonding primary port selection
e8bbf246ce2e system-linux: fix sysfs name for all_ports_active flag
723c699e84f4 Restore disable_ipv6 sysctl after removing a device from bridge or bond
d476e18e8d43 iprule: resolve ipproto by name
7901e66c5f27 netifd: iprule add sport and dport
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 15c2ca0a83)
Link: https://github.com/openwrt/openwrt/pull/19125
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
A previous commit backported the ipq-wifi update to fix support for the
TP-Link Archer C6 v2 by adding the device to the package. However, it
missed adding the required TARGET_ath79 dependency, causing the
ipq-tplink_archer-c6-v2 build to fail.
The dependency was previously added in commit 4990ce613b ("ipq-wifi:
update to 2024-02-17") when several ath79 devices were introduced.
However, since this backport only fixes support for the Archer C6 v2, it
is not feasible to backport all related changes. Therefore, this commit
adds only the missing dependency to resolve the build issue without
pulling in unrelated updates.
Fixes: 0c43acc349 ("ipq-wifi: update to Git HEAD (2025-05-30)")
Signed-off-by: Nick Hainke <vincent@systemli.org>
Link: https://github.com/openwrt/openwrt/pull/19120
Signed-off-by: Robert Marko <robimarko@gmail.com>
Hold a reference to the defer resource as long as it is still needed
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 87bfde67f2)
567207a9bf16 fs: implement fileno() on directory handles
eb1d93235509 fs: support passing directory handle or fd in chdir()
38a2254337f1 build: detect whether toolchain employs default source fortification
6eddfc9dff17 resolv: fix fd leak in send_queries
3d36856b2dc5 uci: fix memory leak on cursor() error
aafde95f1ecf uci: add cursor() flags argument
d8cebc5a6bfd Revert "WIP: lib: support map() over objects"
2599cf80736b zlib: incorporate latest PR changes
830f316a7e49 socker: let sock.peercred() clear error on success
4cbac141406e types: rename u64_to_constant flag to ext_flag
d802fe5da5cd types: add support for resources with embedded data/values
71b4fdc6f60b types: add support for setting resource persistent flag
141f799eba08 uloop: use container_of instead of direct pointer casts
1396f8f2988d uloop: use uc_fn_thisval
9a121fc7440c uloop: drop object_registry
11b804d97086 socket: do not clear last_error in socket.error()
d5b3a9dc1091 socket: add strerror() method
Fixes: https://github.com/jow-/ucode/issues/285
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 2a9316fbfb)
Add kernel package for DesignWare I2C platform controller.
This controller is used on the RP1 SoC found on RPi 5 devices.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 84922a1e34)
The ENC28J60 is a 10 Mbps half-duplex Ethernet controller interfaced via SPI.
It achieves real-world bandwidth up to 5Mbit/s on devices like the RPi Zero due
to SPI limits.
Commonly used with Raspberry Pi Zero boards for wired network connectivity.
Signed-off-by: Albrecht Lohofener <albrechtloh@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19048
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 4987239913)
Add kernel packages for DesignWare SPI core and MMIO controllers.
This is needed for the RP1 SoC found on RPi 5 devices.
Tested with a Microchip ENC28J60 Ethernet controller on a RPi 5.
Signed-off-by: Albrecht Lohofener <albrechtloh@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19049
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 82d20a0fbd)
Rework the generation of the index.json version of the package
indexes to match the original intent (i.e., for use by the ASU
server and other downstream projects). The current file contains
package names that have ABI versioning, making them unusable by ASU,
so we now remove the ABI suffixes.
Also adds a 'version' field to the json, so downstream utilities
can detect the new semantics of the package name fields.
Links: 218ce40cd7
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19051
(cherry picked from commit 2b0b16f1d1)
Link: https://github.com/openwrt/openwrt/pull/19097
Signed-off-by: Robert Marko <robimarko@gmail.com>
lldpd can send several hardware inventory TLV fields. Extend the init
script to provide these when the existing flag 'lldpmed_no_inventory' is
disabled. Five new methods provide default values for some of them,
taken from /etc/os-release and /etc/board.json.
There is no homogeneous method to determine the hardware serial number,
so it can be provided manually, as can asset ID.
Note: properties >= 32 characters are truncated at send time (by lldpd),
and some (Cisco) equipment displays junk after strings >= 32 characters.
So truncate to 31.
Tested on: 24.10.0 (known compatible with 22 and 23 also)
===
Example
===
The following lldpd config lines:
configure inventory hardware-revision "v0"
configure inventory software-revision "r28427-6df0e3d02a"
configure inventory firmware-revision "OpenWrt 24.10.0"
configure inventory serial-number "ABCDEF-123456"
configure inventory manufacturer "glinet"
configure inventory model "GL.iNet GL-MT6000"
# 32 characters:
configure inventory asset "abcdefghijklmnopqrstuvwxyz 12345"
Produce the following TLV (decoded by Wireshark):
Telecommunications Industry Association TR-41 Committee - Inventory - Hardware Revision
1111 111. .... .... = TLV Type: Organization Specific (127)
.... ...0 0000 0110 = TLV Length: 6
Organization Unique Code: 00:12:bb (Telecommunications Industry Association TR-41 Committee)
Media Subtype: Inventory - Hardware Revision (0x05)
Hardware Revision: v0
Telecommunications Industry Association TR-41 Committee - Inventory - Firmware Revision
1111 111. .... .... = TLV Type: Organization Specific (127)
.... ...0 0001 0011 = TLV Length: 19
Organization Unique Code: 00:12:bb (Telecommunications Industry Association TR-41 Committee)
Media Subtype: Inventory - Firmware Revision (0x06)
Firmware Revision: OpenWrt 24.10.0
Telecommunications Industry Association TR-41 Committee - Inventory - Software Revision
1111 111. .... .... = TLV Type: Organization Specific (127)
.... ...0 0001 0101 = TLV Length: 21
Organization Unique Code: 00:12:bb (Telecommunications Industry Association TR-41 Committee)
Media Subtype: Inventory - Software Revision (0x07)
Software Revision: r28427-6df0e3d02a
Telecommunications Industry Association TR-41 Committee - Inventory - Serial Number
1111 111. .... .... = TLV Type: Organization Specific (127)
.... ...0 0001 0100 = TLV Length: 20
Organization Unique Code: 00:12:bb (Telecommunications Industry Association TR-41 Committee)
Media Subtype: Inventory - Serial Number (0x08)
Serial Number: ABCDEF-123456
Telecommunications Industry Association TR-41 Committee - Inventory - Manufacturer Name
1111 111. .... .... = TLV Type: Organization Specific (127)
.... ...0 0000 1010 = TLV Length: 10
Organization Unique Code: 00:12:bb (Telecommunications Industry Association TR-41 Committee)
Media Subtype: Inventory - Manufacturer Name (0x09)
Manufacturer Name: glinet
Telecommunications Industry Association TR-41 Committee - Inventory - Model Name
1111 111. .... .... = TLV Type: Organization Specific (127)
.... ...0 0001 0101 = TLV Length: 21
Organization Unique Code: 00:12:bb (Telecommunications Industry Association TR-41 Committee)
Media Subtype: Inventory - Model Name (0x0a)
Model Name: GL.iNet GL-MT6000
Telecommunications Industry Association TR-41 Committee - Inventory - Asset ID
1111 111. .... .... = TLV Type: Organization Specific (127)
.... ...0 0010 0011 = TLV Length: 35
Organization Unique Code: 00:12:bb (Telecommunications Industry Association TR-41 Committee)
Media Subtype: Inventory - Asset ID (0x0b)
Asset ID: abcdefghijklmnopqrstuvwxyz 1234
The Cisco DUT displays:
Hardware Revision: v0
Firmware Revision: OpenWrt 24.10.0
Software Revision: r28427-6df0e3d02a
Serial Number: ABCDEF-123456
Manufacturer Name: glinet
Model Name: GL.iNet GL-MT6000
Asset ID: abcdefghijklmnopqrstuvwxyz 1234
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18354
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 412c850f07)
Link: https://github.com/openwrt/openwrt/pull/18469
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Some modems and SIM cards take a bit longer to initialize after UIM has been
powered off. Waiting too little time can cause the qmi protocol to end up
in a loop repeatedly power-cycling the SIM card.
Avoid that by
a) increasing the time we unconditionally sleep after --uim-power-on
b) increasing the time we allow uqmi to wait for response for --uim-get-sim-state
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18772
(cherry picked from commit d63663601d)
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18965
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Group 'local' declarations and 'json_get_vars', sort alphabetically within groups, and split off more generic parameters.
- delegate and sourcefilter were not declared as local variables
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
(cherry picked from commit bf768867dc)
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18965
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport upstream commit dropping external definition of mbrtowc. The
said definition conflicts with one provided by GCC 15. Issue found on
24.10 SDK.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
