ERROR: Input tree has errors, aborting (use -f to force output)
arch/arm/boot/dts/qcom-ipq8064.dtsi:1686.14-1698.5: ERROR (phandle_references): /soc/amba/nss-common: Reference to non-existent node or label "smb208_s1b"
A commit which made their way into Linux stable down to 5.15 broke the
SATA support on the BPi-R64.
Fix this by importing a (still pending) patch re-adding the 'syscon'
compatible to the pciesys clock-controller which also contains phy-mode
bits referenced by the ahci_mtk driver expecting to access them using
syscon_regmap_lookup_by_phandle().
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 69890e16b3)
Supported devices are listed in the metadata as the first part of the
DTS compatible. This normally follows the format "vendor,device".
When updating the device name of the 180W 1920-8G PoE an underscore was
used, instead of a comma, to join the vendor and device name. This will
lead to warnings for users wanting to sysupgrade a device with an older
compatible, as the device's info does not match the one the metadata.
Fixes: 987c96e889 ("realtek: rename hpe,1920-8g-poe to match hardware")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 6a7fa68569)
This patch has been accepted for linux v6.14 so we can move it from pending
to backport.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 2f2e21a52b)
This patch is needed on bmips since it fixes issues with GPIOs not being
properly configured due to gpio_request_enable not being called on bcm63xx
devices. Therefore we can now drop the bcm63268 gpio function patch.
Backported from f5b1d340be with the exception of
the realtek and bmips patches removal.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit f5b1d340be)
The Sophos AP15C uses the same hardware as the AP15, but has a reset button.
Based on:
commit 6f1efb2898 ("ath79: add support for Sophos AP100/AP55 family")
author Andrew Powers-Holmes <andrew@omnom.net>
Fri, 3 Sep 2021 15:53:57 +0200 (23:53 +1000)
committer Hauke Mehrtens <hauke@hauke-m.de>
Sat, 16 Apr 2022 16:59:29 +0200 (16:59 +0200)
Unique to AP15C:
- Reset button
- External RJ45 serial console port
Flashing instructions:
This firmware can be flashed either via a compatible Sophos SG or XG
firewall appliance, which does not require disassembling the device, or via
the U-Boot console available on the internal UART header.
To flash via XG appliance:
- Register on Sophos' website for a no-cost Home Use XG firewall license
- Download and install the XG software on a compatible PC or virtual
machine, complete initial appliance setup, and enable SSH console access
- Connect the target AP device to the XG appliance's LAN interface
- Approve the AP from the XG Web UI and wait until it shows as Active
(this can take 3-5 minutes)
- Connect to the XG appliance over SSH and access the Advanced Console
(Menu option 5, then menu option 3)
- Run `sudo awetool` and select the menu option to connect to an AP via
SSH. When prompted to enable SSH on the target AP, select Yes.
- Wait 2-3 minutes, then select the AP from the awetool menu again. This
will connect you to a root shell on the target AP.
- Copy the firmware to /tmp/openwrt.bin on the target AP via SCP/TFTP/etc
- Run `mtd -r write /tmp/openwrt.bin astaro_image`
- When complete, the access point will reboot to OpenWRT.
To flash via U-Boot serial console:
- Configure a TFTP server on your PC, and set IP address 192.168.99.8 with
netmask 255.255.255.0
- Copy the firmware .bin to the TFTP server and rename to 'uImage_AP15C'
- Open the target AP's enclosure and locate the 4-pin 3.3V UART header [4]
- Connect the AP ethernet to your PC's ethernet port
- Connect a terminal to the UART at 115200 8/N/1 as usual
- Power on the AP and press a key to cancel autoboot when prompted
- Run the following commands at the U-Boot console:
- `tftpboot`
- `cp.b $fileaddr 0x9f070000 $filesize`
- `boot`
- The access point will boot to OpenWRT.
Signed-off-by: David Lutz <kpanic@hirnduenger.de>
The kernel logs the error "bcm6368_nand 10000200.nand: there is not valid
maps for state default" on boot and all nand pins show as UNCLAIMED in
sysfs pinmux-pins.
bcm6362.dtsi, bcm6368.dtsi and bcm63268.dtsi use the undocumented property
group which the driver doesn't understand. This has been documented upstream
in commit caf963efd4b0b9ff42ca12e52b8efe277264d35b.
Replacing group with pins allows the nand pins to be properly configured.
Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com>
[add bcm636/bcm6368 and fix commit title]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit d1e9c50d06)
Recent changes to BuildBot config moved the kmods to a dedicated
directory and dropped them from the packages dir. This was needed as
both OPKG and APK gets confused if both entry are present.
To fix this, unconditionally append the kmod feed line if
CONFIG_BUILDBOT is enabled.
Fixes: #17146
Link: https://github.com/openwrt/openwrt/pull/17151
(cherry picked from commit 53ee2e8c03)
[ fix conflict error for missing APK support ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Currently downstream tools like ASU lack information about kernel
version to find out the relevant kmod build folder on downloads server.
So lets fix it by providing a new `linux_kernel` JSON array which would
for the start provide Linux kernel version, revision and vermagic
information.
"linux_kernel": {
"release": "1",
"vermagic": "b57450c07d3a786158c3601fc5cee57d",
"version": "6.6.61"
},
Fixes: openwrt/openwrt#17036Fixes: efahl/owut#9
Co-developed-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17042
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit c857145e03)
Run the invocation of Make with verbosity in order to
prevent the printing of Makefile level and subtarget status.
e.g. make[3] -C target/linux val.DEFAULT_PACKAGES val.ARCH_PACKAGES
Remove piping of stderr, which is only useful when using
the "communicate" method over the "run" method,
and this script would not be written to handle a captured error anyway.
For error testing, stdout and stderr can be set to a file object
with the open() function like this:
out = open('json_out', 'w')
err = open('json_err', 'w')
...
...
stdout=out,
stderr=err,
Signed-off-by: Michael Pratt <mcpratt@pm.me>
(cherry picked from commit fd3376c5ee)
Fixup capabilities parsing in iw output.
In addition to the normal capabilities iw now also outputs HE MAC, HE
PHY and EHT MAC and EHT PHY capabilities. Exclude them in the parsing.
The grep returns this with mac80211-hwsim:
```
root@OpenWrt:~# iw phy phy0 info | grep 'Capabilities:'
Capabilities: 0x107e
HE PHY Capabilities: (0x02bfce0000000000000000):
EHT PHY Capabilities: (0x7c0000feffff7f01):
HE PHY Capabilities: (0x02bfce0000000000000000):
EHT PHY Capabilities: (0x7c0000feffff7f01):
HE PHY Capabilities: (0x02bf000000000000000000):
Capabilities: 0x107e
HE PHY Capabilities: (0x1cbfce0000000000000000):
EHT PHY Capabilities: (0xfc1f3ffeffff7f37):
HE PHY Capabilities: (0x1cbfce0000000000000000):
EHT PHY Capabilities: (0xfc1f3ffeffff7f37):
HE PHY Capabilities: (0x1cbf000000000000000000):
HE PHY Capabilities: (0x1cbfce0000000000000000):
EHT PHY Capabilities: (0xfefffffeffffff7f):
HE PHY Capabilities: (0x1cbfce0000000000000000):
EHT PHY Capabilities: (0xfefffffeffffff7f):
HE PHY Capabilities: (0x1cbf000000000000000000):
Capabilities: 0x107e
```
With busybox 1.36.1 the ht_cap_mask variable will be set to
-72057598332895361. With busybox 1.37.0 it will be set to -1.
Both values are wrong, after this change it will be set to 4222
(0x107E).
Link: https://github.com/openwrt/openwrt/pull/17043
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit adf958c919)
Huawei AP6010DN is a dual-band, dual-radio 802.11a/b/g/n 2x2 MIMO
enterprise access point with one Gigabit Ethernet port and PoE
support.
Hardware highlights:
- CPU: AR9344 SoC at 480MHz
- RAM: 128MB DDR2
- Flash: 32MB SPI-NOR
- Wi-Fi 2.4GHz: AR9344-internal radio
- Wi-Fi 5GHz: AR9580 PCIe WLAN SoC
- Ethernet: 10/100/1000 Mbps Ethernet through Atheros AR8035 PHY
- PoE: yes
- Standalone 12V/2A power input
- Serial console externally available through RJ45 port
- External watchdog: CAT706SVI (1.6s timeout)
Serial console:
9600n8 (9600 baud, no stop bits, no parity, 8 data bits)
MAC addresses:
Each device has 32 consecutive MAC addresses allocated by
the vendor, which don't overlap between devices.
This was confirmed with multiple devices with consecutive
serial numbers.
The MAC address range starts with the address on the label.
To be able to distinguish between the interfaces,
the following MAC address scheme is used:
- eth0 = label MAC
- radio0 (Wi-Fi 2.4GHz) = label MAC + 1
- radio1 (Wi-Fi 5GHz) = label MAC + 2
Installation:
0. Connect some sort of RJ45-to-USB adapter to "Console" port of the AP
1. Power up the AP
2. At prompt "Press f or F to stop Auto-Boot in 3 seconds",
do what they say.
Log in with default admin password "admin@huawei.com".
3. Boot the OpenWrt initramfs from TFTP using the hidden script "run ramboot".
Replace IP address as needed:
> setenv serverip 192.168.1.10
> setenv ipaddr 192.168.1.1
> setenv rambootfile openwrt-ath79-generic-huawei_ap6010dn-initramfs-kernel.bin
> saveenv
> run ramboot
4. Optional but recommended as the factory firmware cannot be downloaded publicly:
Back up contents of "firmware" partition using the web interface or ssh:
$ ssh root@192.168.1.1 cat /dev/mtd11 > huawei_ap6010dn_fw_backup.bin
5. Run sysupgrade using sysupgrade image. OpenWrt
shall boot from flash afterwards.
Return to factory firmware (using firmware upgrade package downloaded from non-public Huawei website):
1. Start a TFTP server in the directory where
the firmware upgrade package is located
2. Boot to u-boot as described above
3. Install firmware upgrade package and format the config partitions:
> update system FatAP6X10XN_SOMEVERSION.bin
> format_fs
Return to factory firmware (from previously created backup):
1. Copy over the firmware partition backup to /tmp,
for example using scp
2. Use sysupgrade with force to restore the backup:
sysupgrade -F huawei_ap6010dn_fw_backup.bin
3. Boot AP to U-Boot as described above
Quirks and known issues:
- The stock firmware has a semi dual boot concept where the primary
kernel uses a squashfs as root partition and the secondary kernel uses
an initramfs. This dual boot concept is circumvented on purpose to gain
more flash space and since the stock firmware's flash layout isn't
compatible with mtdsplit.
- The external watchdog's timeout of 1.6s is very hard to satisfy
during bootup. This is why the GPIO15 pin connected to the watchdog input
is configured directly in the LZMA loader to output the AHB_CLK/2 signal
which keeps the watchdog happy until the wdt-gpio kernel driver takes
over. Because it would also take too long to read the whole kernel image
from flash, the uImage header only includes the loader which then reads
the kernel image from flash after GPIO15 is configured.
Signed-off-by: Marco von Rosenberg <marcovr@selfnet.de>
(cherry picked from commit f84a9f7dc0)
Link: https://github.com/openwrt/openwrt/pull/16978
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Added patch:
generic/backport-5.15/430-v6.3-udf-Allocate-name-buffer-in-directory-iterator-on-he.patch
This patch fixes the following compile warning:
```
CC [M] fs/udf/namei.o
fs/udf/namei.c: In function 'udf_rename':
fs/udf/namei.c:878:1: error: the frame size of 1144 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
878 | }
| ^
cc1: all warnings being treated as errors
make[7]: *** [scripts/Makefile.build:289: fs/udf/namei.o] Error 1
```
Link: https://github.com/openwrt/openwrt/pull/16882
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Manually adapted:
bcm27xx/patches-5.15/950-0166-xhci-Use-more-event-ring-segment-table-entries.patch
I replaced it with the version from main branch which applies more easily
bcm27xx/patches-5.15/950-0600-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
bcm27xx/patches-5.15/950-0605-xhci-refactor-out-TRBS_PER_SEGMENT-define-in-runtime.patch
bcm27xx/patches-5.15/950-0606-usb-xhci-add-VLI_TRB_CACHE_BUG-quirk.patch
bcm27xx/patches-5.15/950-0717-usb-xhci-add-a-quirk-for-Superspeed-bulk-OUT-transfe.patch
bcm53xx/patches-5.15/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
generic/hack-5.15/645-netfilter-connmark-introduce-set-dscpmark.patch
Added patch:
generic/backport-5.15/777-netfilter-xtables-fix-typo-causing-some-targets-to-not-load-on-IPv6.patch
This fixes a bug intoduced in this version.
Adapt kernel configuration for newly added option
CONFIG_PROC_MEM_ALWAYS_FORCE.
Link: https://github.com/openwrt/openwrt/pull/16882
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patches weren't refreshed when r8168 was updated to v8.054.00 in a85e18b53f.
Fixes: a85e18b53f ("kernel: r8168: update to v8.054.00")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 6490c88c75)
Mark the package as nonshared to build it in the target specific build
step 1 of the build bots instead of the architecture generic build step 2.
In the build step 2 it may be left out if we build it using a different
target.
Fixes: #16857
Link: https://github.com/openwrt/openwrt/pull/16859
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix in commit 25eead21c5 ("ath79: fix 5GHz on QCA9886 variant of ZTE MF286")
was incomplete. A user of such variant popped up, and in the boot log
after installation, we discovered that QCA9886 expects different
pre-calibration data size, than the older QCA9880 variant:
ath10k_pci 0000:00:00.0: qca9888 hw2.0 target 0x01000000 chip_id 0x00000000 sub 0000:0000
ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
ath10k_pci 0000:00:00.0: firmware ver 10.4b-ct-9888-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 59e741e7
ath10k_pci 0000:00:00.0: invalid calibration data length in nvmem-cell 'pre-calibration': 2116 != 12064
ath10k_pci 0000:00:00.0: Loading BDF type 0
ath10k_pci 0000:00:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0056,subsystem-vendor=0000,subsystem-device=0000 from ath10k/QCA9888/hw2.0/board-2.bin
ath10k_pci 0000:00:00.0: failed to fetch board-2.bin or board.bin from ath10k/QCA9888/hw2.0
ath10k_pci 0000:00:00.0: failed to fetch board file: -12
ath10k_pci 0000:00:00.0: could not probe fw (-12)
Explicitly define a pre-calibration nvmem-cell for this variant, and use
it instead of the calibration one, which is shorter.
Fixes: 25eead21c5 ("ath79: fix 5GHz on QCA9886 variant of ZTE MF286")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit fc236f3b3c)
Link: https://github.com/openwrt/openwrt/pull/16810
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This reverts commit ec8f647d16, as with the
current kernel version, the change actually causes the same bug it once
may have fixed -- that is, the leds are now again reversed.
I suspect this was due to a switch to a newer kernel version between when
the patch was submitted and now reversing the order of the interfaces, so
that eth0 / the LAN interface is also the interface used for PoE, and eth1
/ the WAN interface is the non-PoE interface.
Signed-off-by: Rafal Boni <rafal.boni@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16779
(cherry picked from commit b5e1544f4d)
Signed-off-by: Rafal Boni <rafal.boni@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16822
Signed-off-by: Robert Marko <robimarko@gmail.com>
This patch adds support for the MikroTik RouterBOARD 750 r2, marketed as
hEX lite, a small indoor router with 5x 10/100 Mbps Ethernet ports, one
with PoE in. The device was already supported by the ar71xx target.
Specifications:
- SoC: Qualcomm Atheros QCA9533
- Flash: 16 MB SPI NOR
- RAM: 64 MB
- Ethernet: 4x 10/100 Mbps LAN, 1x 10/100 Mbps WAN (PoE in)
- LEDs: 5x Ethernet port activity (green), 1x user (green)
- Buttons: 1x reset
See https://mikrotik.com/product/RB750r2 for more details.
Not working:
- Serial port (already not working in ar71xx)
Flashing:
TFTP boot initramfs image and then perform sysupgrade. Only the
"Internet" port will ask for an initramfs image. Follow common
MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.
(cherry picked from commit 8486c677b8)
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Link: https://github.com/openwrt/openwrt/pull/13477
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
From the upstream repo:
Instead of assuming only one register is used, track all 16 regs
individually.
This avoids need for the 'PREV_PAYLOAD' hack and also avoids the need to
clear out old flags:
When we see that register 'x' will be written to, that register state is
reset automatically.
Existing dissector decodes
ip saddr 1.2.3.4 meta l4proto tcp
... as
-s 6.0.0.0 -p tcp
iptables-nft -s 1.2.3.4 -p tcp is decoded correctly because the expressions
are ordered like:
meta l4proto tcp ip saddr 1.2.3.4
|
... and 'meta l4proto' did clear the PAYLOAD flag.
The simpler fix is:
ctx->flags &= ~NFT_XT_CTX_PAYLOAD;
in nft_parse_cmp(), but that breaks dissection of '1-42', because
the second compare ('cmp lte 42') will not find the
payload expression anymore.
This commit fixes#11169 and openwrt/packages#22727, and potentially anyone that uses iptables-nft legacy support.
Signed-off-by: Rodrigo B. de Sousa Martins <rodrigo.sousa.577@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16504
[Added patch header]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 44b1993f76)
It seems that some Xiaomi AX3000T boards changed to using Winbond W25N01KV
SPI-NAND which is not supported in OpenWrt 23.05 but only in main.
So, backport the support for Winbond W25N01KV from Linux 6.12 to 23.05
as well.
Link: https://github.com/openwrt/openwrt/pull/16669
Signed-off-by: Robert Marko <robimarko@gmail.com>
